• 대한조선학회논문집
• /
• 제38권2호
• /
• pp.53-61
• /
• 2001

자유곡면으로 이루어진 모형선의 표면을 가공할 수 있는 공작기계를 개발하고 서보시스템으로 절삭공구의 가공경로제어를 수행하였다. 서보시스템은 BLDC(Blushless DC) motor, 콘트롤 드라이버, 호스트 콘트롤러로 구성되어 있다. 또한 정밀한 가공을 위하여 PI제어기를 사용하였고 Visual C++를 이용한 GUI(Graphic User Interface)를 구성하였다. 개발된 자유곡면 가공시스템에 의해 모형선이 가공되었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 A
• /
• pp.179-182
• /
• 1998

This paper is proposed a selection method of the major design dimension which constrain the maximum acceleration capability and minimum power loss of surface-mounted brushless do motor with NdFeB permanent magnet for servo drives. Expressions are derived from the air-gap flux density and the linear current density around the stator periphery and design dimensions. The linear current density is limited by the need to avoid demagnetization. In this paper, We compute the optimum design dimensions of 2KW BLDC motor with maximum acceleration capability and minimum power loss by using genetic algorithm.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.624-627
• /
• 2000

An adaptive fuzzy sliding-mode control system which combines the merits of sliding-mode control the fuzzy inference mechanism and the adaptive algorithm is proposed. A fuzzy sliding-mode controller is investigated in which a simple fuzzy inference mechamism is used to estimate the upper bound of uncertainties., The fuzzy inference mechanism with centre adaptation of membership functions is investigated to estimate the optimal bound of uncertainties.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.1509-1512
• /
• 2003

The electric power wheelchair needs to control motor torque and speed for responding to variable actions given by handling a joystick. In this paper a DSP-based BLDC motor controller using a single dc-link current sensor is presented for electric power wheelchair. It is composed by a DSP processor and three-phase inverter module. To control torque, high speed current control is achieved by the PI controller and pulse width modulation (PWM) signals with 25 kHz carrier frequency, which is performed by 200 ${\mu}sec$ cycle. The speed controller computes the new direct current reference from the speed error and the PI control equation. The displacement value by handling the joystick is converted to reference speeds of right and left wheel motors using nonholonomic wheelchair kinematics. Experimental results show that the presented control system is enough to implement a speed servo in wheelchair driving.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권3호
• /
• pp.131-138
• /
• 1999

Generally, the digital controller has many advantages such as high precision, robustness to electrical noise, capability of flexible programming and fast response to the load variation. In this study, we have established proper mathematical equivalent model of Brushless DC (BLDC) motor and estimated the motor parameter by means of the back-emf measurement as being the step input to the controlled target BLDC motor. And the validity of proposed estimation method is confirmed by the test result of step response. As well, we have designed the reasonable digital controller as a consequence of the root locus method which is obtained from the open-loop transfer function of BLDC motor with hall sensor, and the determination of control gain for variable speed control. Here, revised Ziegler-Nichols tuning method is applied for the proper digital gain establishment, and the system stability is verified by the frequency domain analysis with Bode-plot and experimentation.

• 전력전자학회논문지
• /
• 제22권5호
• /
• pp.449-456
• /
• 2017

This study proposes a method for compensating for the commutation torque ripple of delta-connected brushless DC motors with low inductance based on a current predictions. At the commutation instant, a phase current at the next sampling period is predicted and compared with the reference phase current to determine whether torque ripples will occur or not. If the predicted current cannot reach the reference phase current, the reference current is modified and the relevant voltage reference is produced to reduce the torque ripple. The validity of the proposed method has been verified by simulation and experimental results. The commutation torque ripple has been decreased by 17.7% at 1,000 rpm and 80% load conditions.

• 전력전자학회논문지
• /
• 제6권5호
• /
• pp.416-422
• /
• 2001

BLDC (Brushless DC) 전동기는 선형적인 토크 대 전류, 속도 대 전압특성을 갖고 있으며 기계적 전기적인 잡음이 없고, 가감속 제어가 용이하며, 토크 대 관성의 비가 매우 높아 소형으로 높은 출력을 낼 수 있다는 장점을 가지고 있다. 그러나 전기자 전류의 전환 (Commutation)시 고정자 권선의 인덕턴스 성분과 역기전력으로 인해 발생되는 전류리플은 BLDC 전동기의 구동시 발생되는 토크리플의 중요한 원인이 되어, 고정밀 서보계통에 대한 응용에 큰 장애가 되고 있다. 본 논문에서는 퓨리에 시리즈계수를 사용한 새로운 전류제어 알고리즘을 개발하여 상전류 전환시 발생하는 전류리플을 최소화함으로서 토크리플을 현저히 감소 시켰으며, BLDC 전동기의 구동을 위해 널리 사용되고 있는 UNIPOLAR PWM 방식과 시뮬레이션 및 실험을 통해 비교함으로써, 새로운 알고리즘의 효용성을 입증하고자 한다.

• 한국전자통신학회논문지
• /
• 제14권5호
• /
• pp.1009-1018
• /
• 2019

본 연구에서는 표면근전도 측정기 기반의 재활의료기기의 설계 및 구현에 관한 내용을 기술한다. 재활시스템은 BLDC모터와 모터 드라이브를 이용하여 제어된다. BLDC모터 드라이브는 동작제어를 하며, 속도는 외부 서보모터를 통해 드라이브를 제어한다. 또한 모터 외부에 결합된 포텐쇼미터는 모터에 의해 회전하는 부하 위치 정보를 전달한다. 재활 알고리즘은 환자가 일정 각도 범위에서 주기적인 수축 이완 재활운동을 속도단계별로 실행하며 재활운동 시 사용자 설정 단계에 따른 모터를 활용하여 $0{\sim}120[^{\circ}]$의 최대각도로 제한하여 제어한다. 보행 알고리즘은 양쪽 안쪽넓은근에 부착된 표면근전도 측정기로 획득한 신호의 차이 값을 이용하여 근전도 신호가 낮은 다리에 모터제어로 보상해주며 보행운동 시 모터와 표면근전도 측정기를 활용하여 $0{\sim}88[^{\circ}]$의 최대각도로 제한하여 제어한다.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제49권8호
• /
• pp.451-458
• /
• 2000

The precise speed and position control technique for Brushless DC Motor demands accurate position and speed feedback information. Generally, resolver or absolute encoders are used as speed and positiion sensor. But they increase cost and more problem happens at low speed than high speed specially. Therefore, in this paper, optimal speed observer is proposed for decreasing size and cost of whole system. And also, we consider the error problem about the system modeling and measurement at low speed range as well as high speed. The overall system consists of two parts, a drive and a speed observer. We make use of Least square curve fitting algorithm as speed observer and can overcome low resolution by proposed observer. Also, because of using the signal of hall sensor, robust control is possible in low speed as well as high speed for the change of the parameters of the system and disturbance. To construct observer using the signal of hall sensor, we design the pulse multiplier circuit and the software of microprocessor, AT89CC2051. Finally, the performance of the proposed observer is exemplified by some simulations and experiments.

• 천문학논총
• /
• 제21권2호
• /
• pp.81-86
• /
• 2006

Even though 30inch optical telescope at Kyung Hee Astronomy Observatory has been used to produce a series of scientific achievements since its first light in 1992, numerous difficulties in operating of the telescope have hindered the precise observations needed for further researches. Since the currently used PC-TCS(Personal Computer based Telescope Control System) software based on ISA-bus type is outdated, it doesn't have a user friendly interface and make it impossible to scale. Also accumulated errors which are generated by discordance from input and output signals into a motion controller required new control system. Thus we have improved the telescope control system by updating software and modifying mechanical parts. We applied a new BLDC(brushless DC) servo motor system to the mechanical parts of the telescope and developed a control software using Visual Basic6.0. As a result, we could achieve a high accuracy in controlling of the telescope and use the user friendly GUI(Graphic User Interface).