• Korean Journal of Food Science and Technology
• /
• v.36 no.3
• /
• pp.432-439
• /
• 2004

Increase in water vapor barrier properties of sodium alginate films was studied by preparing composite films with fatty acids, i.e., lauric, palmitic, stearic, and oleic acids, and by treatment with 3% $CaCl_{2}$ solution for 3 min. Film thickness, surface color, microstructure, tensile strength (TS), elongation at break (E), water vapor permeability (WVP), water solubility (WS), and sorption isotherm of films were investigated. Microstructure of films observed with SEM was changed by fatty acid and $CaCl_{2}$ treatments. TS decreased 25-70% depending on fatty acid used, and increased 1.5- to 2-fold by $CaCl_{2}$ treatment. E decreased by both fatty acid and $CaCl_{2}$ treatments. Except oleic acid, WVP decreased significantly (p<0.05) by forming composite films with fatty acids, particularly with stearic acid, WVP decreased more than two-fold. WS also decreased by fatty acid and $CaCl_{2}$ treatments. In stearic acid, WS decreased about 30-fold by combined treatment of fatty acid and $CaCl_{2}$. Sorption isotherm showed typical biphasic pattern with deliquescent point of 0.75. Results of isotherms and BET monolayer moisture content indicated hydrophilicity of film decreased by $CaCl_{2}$ treatment.

• Korean Chemical Engineering Research
• /
• v.51 no.2
• /
• pp.208-213
• /
• 2013

Zirconium hydroxide was synthesized by varying the aging time of the zirconyl chloride octahydrate at $100^{\circ}C$ in aqueous solution and the resulting hydroxides were calcined at $700^{\circ}C$ for 6 h to obtain the crystalline $ZrO_2$. The materials used in this study were characterized by differential thermal analysis (DTA), X-ray diffraction (XRD), $N_2$-sorption, transmission electron microscopy (TEM), $NH_3$ temperature-programmed desorption ($NH_3$-TPD), $CO_2$-TPD and iso-propanol TPD analyses to correlate with catalytic activity for the dehydration of iso-propanol. The pure tetragonal $ZrO_2$ phase was obtained after 24 h aging of zirconium hydroxide and successive calcination at $700^{\circ}C$. The increase of aging time showed the production of smaller particle size $ZrO_2$ resulting that the higher specific surface area and total pore volume. $NH_3$-TPD results revealed that the relative acidity of the catalysts increased along with the increase of aging time. On the other hand, the results of $CO_2$-TPD showed the reverse trend of $NH_3$-TPD results. The best catalytic activity for the dehydration of iso-propanol to propylene was shown over $ZrO_2$ catalyst aged for 168 h which had the highest $S_{BET}$ ($178\;m^2\;g^{-1}$). The catalytic activity could be correlated with high surface area, relative acidity and easy desorption of iso-propanol.

• Korean Chemical Engineering Research
• /
• v.43 no.4
• /
• pp.517-524
• /
• 2005

Barium titanate ($BaTiO_3$) particles were prepared by spray pyrolysis from spray solution containing organic additives. The effects of the type and amount of organic precursors on the crystal structure and morphology of the $BaTiO_3$ particles were investigated. It was found that the morphology of $BaTiO_3$ particles before and after calcination depended on the type of organic additives such as citric acid, ethylene glycol and polyethylene glycol. Among these organic additives, citric acid was the most effective to prepare $BaTiO_3$ particles with nano-structured morphology consisting with uniform size nanometer particles after calcination. It was also found that the phase transformability of the metastable cubic phase to the tetragonal one during calcination could be improved by increasing the content of citric acid in the spray solution. As a result, $BaTiO_3$ particles prepared from spray solution containing high concentration of citric acid had good tetragonality, uniform and fine size, and high BET surface area after calcination. $BaTiO_3$ particles prepared by spray pyrolysis had nanometer size and uniform morphology after simple ball milling process.

• Journal of the Korean Ceramic Society
• /
• v.34 no.2
• /
• pp.163-170
• /
• 1997

The retarding effects of MgSiF6.6H2O on the hydration of portland cement were studied. The setting time, flow value and compressive strength of mortar were measured and the mechanism of retardation was also studied by ion concentration in solution, SEM, BET, and X-ray diffraction. The results are as follows ; 1. Setting time was delayed by the addition of MgSiF6.6H2O. 2. The flow value of mortar decreases depending upon the amount of MgSiF6.6H2O. 3. The compressive strength was almost same or some increase on 28 days hydration. 4. The main retardation mechanism of MgSiF6 on the hydration of portland cement may be explained by the following hypothesis. MgSiF6 depressing the Ca++ and K+ ion concentration of cement paste solution be-cause of the recrystalization of K2SiF6 and CaF2 phase. The new products of K2SiF6 and CaF2 deposit on the surface of unhydrated cement powder and harzard the mass transfer through these layer. The low con-centration of Ca++, K+ ion in solution was decreasing the hydration rate of portland cement.

• Polymer(Korea)
• /
• v.32 no.1
• /
• pp.70-76
• /
• 2008

The PES-g-BTCA membrane was synthesized by UV irradiation method and then used to be modified into the PES anion exchange membrane by the amination reaction. Their chemical structures and adsorption properties were investigated. The degree of grafting and amination were increased with increasing the reaction time and had the maximum values of 138% and 1.20 mmol/g at 80 min, respectively. The initial thermal degradation temperature of PES membrane was $400^{\circ}C$. Which was reduced as the surface modification reaction had proceeded. The values of contact angle for PES membrane were decreased from 68.1 to $40.2^{\circ}$ with increasing the extent of amination, the water up-take and ion exchange capacity were also increased with increasing UV irradiation time until 80 min. The average pore size and BET surface area were decreased in order of PES, PES-g-BTCA, and aminated PES ion exchange membrane. Their average pore sizes were 624.8, 359.7, and 138.5 ${\AA}$, and their surface areas were 10.1,9.7 and 1.7 $m^2/g$, respectively.

• Journal of the Korean Chemical Society
• /
• v.65 no.3
• /
• pp.197-202
• /
• 2021

In this study, activated clay treated with H₂SO₄ (20% by weight) and heat at 90 ℃ for 8 h for acid white soil was used as an adsorbent for the removal of PO₄^3--P in water. Prior to the adsorption experiment, the characteristics of activated clay was examined by X-ray Fluorescence Spectrometry (XRF) and BET surface area analyser. The adsorption of PO₄^3--P on activated clay was steeply increased within 0.25 h and reached equilibrium at 4 h. At 5 mg/L of low PO₄^3--P concentration, roughly 98% of adsorption efficiency was accomplished by activated clay. The adsorption data of PO₄^3--P were introduced to the adsorption isotherm and kinetic models. It was seen that both Freundlich and Langmuir isotherms were applied well to describe the adsorption behavior of PO₄^3--P on activated clay. For adsorption PO₄^3--P on activated clay, the Freundlich and Langmuir isotherm coefficients, K_F and Q, were found to be 8.3 and 20.0 mg/g, respectively. The pseudo-second-order kinetics model was more suitable for adsorption of PO₄^3--P in water/activated clay system owing to the higher correlation coefficient R² and the more proximity value of the experimental value q_e,exp and the calculated value q_e,cal than the pseudo-first-order kinetics model. The results of study indicate that activated clay could be used as an efficient adsorbent for the removal of PO₄³-P from water.

• Korean Chemical Engineering Research
• /
• v.46 no.5
• /
• pp.1008-1012
• /
• 2008

Nanoscale zero-valent iron(nZVI) is famous for its high reactivity originated from its high surface area and it has received considerable attentions as one of the latest innovative technologies for treating contaminated groundwater. Due to its fine powdery form, nZVI has limited filed applications. The efforts to overcome this shortcoming by immobilizing nZVI on a supporting material have been made. This study investigated the differences of resin-supported nZVI's characteristics by changing the preparation methods and evaluated its reactivity. The borohydride reduction of an iron salt was proceeded in ethanol/water solvent containing a dispersant and the synthesis was conducted in the presence of ion-exchange resin. The resulting material was compared to that prepared in a conventional way of using de-ionized water by measuring the phyrical and chemical characteristics. BET surface area and Fe content of nZVI-attached resin was increased from $31.63m^2/g$ and 18.19 mg Fe/g to $38.10m^2/g$ and 22.44 mg Fe/g, respectively, by switching the solution medium from water to ethanol/water with a dispersant. The reactivity of each material was tested using nitrate solution without pH control. The pseudo first-order constant of $0.462h^{-1}$ suggested the reactivity of resin-supported nZVI prepared in ethanol/water was increased 61 % compared to that of the conventional type of supported nZVI. The specific reaction rate constant based on surface area was also increased. The results suggest that this new supported nZVI can be used successfully in on-site remediation for contaminated groundwater.