• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.10
• /
• pp.1997-2007
• /
• 2002

Composite air spindles are appropriate for the high-speed and the high-precision machining as small hole drilling of printed circuit board (PCB) or wafer cutting for manufacturing semiconductors because of the low rotational inertia, the high damping ratio and the high fundamental natural frequency of composite shaft. The axial load and stiffness of composite air spindles fur drilling operation are determined by the thrust ben ring composed of the air supply part mounted on the housing and the rotating part mounted on the rotating shaft. At high-speed rotation, the rotating part of the thrust bearing should be designed considering the stresses induced by centrifugal force as well as the axial stiffness and the natural frequency of the rotating shaft to void the shaft from failure due to the centrifugal force and resonant vibration. In this work, the air supply part of the thrust bearing was designed considering the bending stiffness of the bearing and the applied load. The rotating part of the thrust bearing was designed through finite element analysis considering the cutting forces during manufacturing as well as the static and dynamic characteristics under both the axial and con trifugal forces during high-speed rotation.

• Journal of Korean Society of Steel Construction
• /
• v.9 no.1 s.30
• /
• pp.107-120
• /
• 1997

The purpose of this study is to develop composite structural system which is to have versatility in plan design and to improve economical efficieney, to maximise structural capacity than existing structural system. In this viewpoint, it was investigated to the properties of structural behaviors for i oint consisting of concrete filled steel square tube column and P.C reinforced concrete beam through a series of hysteretic behavior experiment. In the previous report, researched to the properties of joints with key parameters. such as Axial Force ratio and section types. From the based on previous results, this study investigated the properties of this joints with key parameters, such as strength of concrete, size of panel zone and Axial Force ratio. The obtained results are summarised as follows. (1) Investigating for the failure mode of the beam-to-column joint, the specimens of S,LL and LH series(except for L5H) presented flexural failure mode. (2) The initial stiffness of joint was increasd as the decrease of axial force ratio and increase of the concrete strength. (3) The rotation resisting capacity was effective as the increment of the concrete strength and decrement of the axial force ratio. (4) The emprical formula to predict the ultimate capacity of joint model to introduce decrease coefficient according to the axial force ratio to superimpose shearing strength of steel web(H section) and bending strength of reinforced concrete beam was expected.

• Structural Engineering and Mechanics
• /
• v.1 no.1
• /
• pp.17-30
• /
• 1993

A practical multi-spring model is proposed for a nonlinear analysis of reinforced concrete members, especially columns, taking into account the interaction of axial load and bi-directional bending moment. The parameters of the model are determined on the basis of material properties and section geometry. The axial force-moment interaction curve of reinforced concrete sections predicted by the model was shown to agree well with those obtained by the flexural analysis utilizing realistic stress-strain relations of materials. The reliability of the model was also examined with respect to the test of reinforced concrete columns subjected to varying axial load and bi-directional lateral load reversals. The analytical results agreed well with the experiment.

• Journal of the Korean Society of Physical Medicine
• /
• v.9 no.4
• /
• pp.425-432
• /
• 2014

PURPOSE: The purpose of this study was to investigate that the differences in sternocleidomastoid muscle activity, neck rotation angle, neck lateral bending angle and neck lateral bending onset time between conditions with and without visual biofeedback during neck rotation. METHODS: Ten male and four female adults with condition of forward head posture were recruited in this study. Subjects conducted to left and right maximal neck rotation under the conditions with and without visual biofeedback. During neck rotation, kinematic data of neck rotation, neck lateral bending movement, and electromyography activities of bilateral sternocleidomastold muscles were collected. Differences in dependent variables between conditions with and without visual biofeedback were analyzed using paired t-test. RESULTS: There were significant decreases in lateral bending angle, while lateral bending movement onset time was delayed significantly when applying visual biofeedback (p<.05). However, there were no significant differences in the activation of left and right sternocleidomastoid muscles and neck rotation angle between conditions with and without visual biofeedback (p>.05). CONCLUSION: These findings suggest that visual biofeedback may be effective for axial rotation of cervical spine during neck rotation in adults with forward head posture.

• Journal of Korean Ophthalmic Optics Society
• /
• v.15 no.3
• /
• pp.213-217
• /
• 2010

Purpose: To emphasize the necessity of post-fitting by follow-up test, the mis-alignment was analyzed after initial wearing of toric soft contact lenses (TSCL). Methods: After trial contact lenses were worn to 87 eyes with myopic astigmatism for 1 week, we observed the alignment of axis mark on trial contact lenses using slit lamp and corrected the rotated axis by method of LARS. After final fitting, rotation ratio, rotation degree and rotation position were analyzed compared to initial prescription divided to amount of cylinderical and spherical powers. Results: Rotation ratio of TSCL's axis was increased as increment of both cylinderical powers and (-)spherical powers. An average of rotation degree was $10^{\circ}{\sim}13^{\circ}$ which was not related to amount of their powers. Rotation position of TSCL's axis was more to temporal than to nasal. Conclusions: Because mis-alignment of axis after TSCL wearing induce the poor sight, adjustment of axial alignment as a result of follow-up must be performed.

• Korean Journal of Radiology
• /
• v.2 no.4
• /
• pp.216-221
• /
• 2001

Objective: To compare, in terms of their demonstration of tears of the anterior glenoid labrum, oblique axial MR arthrography obtained with the patient's shoulder in the abduction and external rotation (ABER) position, with conventional axial MR arthrography obtained with the patient's arm in the neutral position. Materials and Methods: MR arthrography of the shoulder, including additional oblique axial sequences with the patient in the ABER position, was performed in 30 patients with a clinical history of recurrent anterior shoulder dislocation. The degree of anterior glenoid labral tear or defect was evaluated in both the conventional axial and the ABER position by two radiologists. Decisions were reached by consensus, and a three-point scale was used: grade 1=normal; grade 2=probable tear, diagnosed when subtle increased signal intensity in the labrum was apparent; grade 3=definite tear/defect, when a contrast material-filled gap between the labrum and the glenoid rim or deficient labrum was present. The scores for each imaging sequence were averaged and to compare conventional axial and ABER position scans, Student's t test was performed. Results: In 21 (70%) of 30 patients, the same degree of anterior instability was revealed by both imaging sequences. Eight (27%) had a lower grade in the axial position than in the ABER position, while one (3%) had a higher grade in the axial position. Three whose axial scan was grade 1 showed only equivocal evidence of tearing, but their ABER-position scan, in which a contrast material-filled gap between the labrum and the glenoid rim was present, was grade 3. The average grade was 2.5 (SD=0.73) for axial scans and 2.8 (SD=0.46) for the ABER position. The difference between axial and ABER-position scans was statistically significant (p<0.05). Conclusion: MR arthrography with the patient's shoulder in the ABER position is more efficient than conventional axial scanning in revealing the degree of tear or defect of the anterior glenoid labrum. When equivocal features are seen at conventional axial MR arthrography, oblique axial imaging in the ABER position is helpful.

• Korea-Australia Rheology Journal
• /
• v.21 no.2
• /
• pp.119-126
• /
• 2009

A numerical analysis is performed to investigate the effect of rotation on the blood flow characteristics with four different angular velocities. The artery has a cylindrical shape with 50% stenosis rate symmetrically distributed at the middle. Blood flow is considered a non-Newtonian fluid. Using the Carreau model, we apply the pulsatile velocity profile at the inlet boundary. The period of the heart beat is one second. In comparison with no-rotation case, the flow recirculation zone (FRZ) contracts and its duration is reduced in axially rotating artery. Also wall shear stress is larger after the FRZ disappears. Although the geometry of artery is axisymmetry, the spiral wave and asymmetric flow occur clearly at the small rotation rate. It is caused that the flow is influenced by the effects of the rotation and the stenosis at same time.

• The Korean Journal of Pain
• /
• v.12 no.2
• /
• pp.231-234
• /
• 1999

Until several years ago we didn't think seriously about cervical problems as a cause of headaches, but since the publication of articles by Bogduk et al they have gotten more attention. Cervical headaches are associated with movement abnormalities of the structures of the neck such as cervical nerve roots, discs, joints and soft tissues. Considering this, we thought that the atlanto-axial joint could be one of the causes of these headaches. Headaches originating from this joint can be recognized by the fact that the pain worsens with rotation of the head in the horizontal plane. Pain can also be referred to the frontal area or around the orbit. We did atlanto-axial joint blocks using a posterior approach on 10 patients who suffered from this type of headache. The results were promising with 9 out of 10 patients showing more than 50% improvement on the numeric rating scale. There were no serious complications observed. We concluded that the atlanto-axial joint block can be an effective procedure in treating this specific type of headache.

• Korean Institute of Interior Design Journal
• /
• v.17 no.5
• /
• pp.23-30
• /
• 2008

This thesis aims to analyze the visual perceptual effects drawn by 'axial composition and divergence' and to interpret the architecture of Kahn in respect of 'axial composition and divergence'. Axial composition of the form, the location of the entrance and divergence of internal movement were checked up about 53 works by extracting parti which is basic element of spatial composition. The 3D modeling simulation was performed for the selected 10 works in order to analyze the visual perceptual effect due to divergence of the internal movement. The reaction of the observer's actions and visual perception by 'axial composition and divergence' is presented in the following steps. 1. Divergence of the entrance/a panorama of expanding planes. 2. Divergence of internal movement/The process of perception of visual rotation and central spatial form. 'Perceptive form' created by 'divergence' is the result of diverse and flexible series of processes which must be experienced in person in order to reach the space as a room with a definite domain and center.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.297-302
• /
• 2005

Right hand circularly polarized Ka band microstrip patch array antenna was designed, manufacture and measurement were carried out. In order to lower axial ratio performance sequential rotation array technique was used. With mono-pulse feed There are sum and delta channel. Waveguide to microstrip transition was used. The 512 array antenna was performed which axial ratio is about 1.ldB in the half power beam width and also 1.ldB at the normal direction. Directivity gain of designed antenna is 32dB.