• Journal of the Korean Society for Heat Treatment
• /
• v.30 no.6
• /
• pp.258-263
• /
• 2017

The effect of cooling rate on the damping capacity of pure Mg was studied. Two Mg samples with different cooling rates were prepared by heat treatment at 873 K for 24 h, followed by water quenching and by furnace cooling to room temperature, respectively. The average grain sizes of the Mg samples were almost identical regardless of the cooling rate, but more twins were observed in the sample with faster cooling rate. The calculated vacancy fraction was higher in the fast cooling sample than the slow cooling one. It is noted that the fast cooling sample exhibited lower damping capacity both in the strain-amplitude independent and strain-amplitude dependent regions. Higher values of vacancy concentration and number density of twins in the fast cooling sample are considered to be responsible for the deteriorated damping capacity in the strain-amplitude independent and strain-amplitude dependent regions, respectively.

• Journal of the Korean Ceramic Society
• /
• v.54 no.1
• /
• pp.38-42
• /
• 2017

Vanadium nitride (VN) coatings were deposited using inductively coupled plasma (ICP) assisted sputtering at different ICP powers. Microstructural, crystallographic and mechanical characterizations were performed by FE-SEM, AFM, XRD and nanoindentation. The results show that ICP has significant effects on coating's microstructure, structural and mechanical properties of VN coatings. With an increase in ICP power, coating microstructure evolved from a porous columnar structure to a highly dense one. Single- phase cubic (FCC) VN coatings with different preferential orientations and residual stresses were obtained as a function of ICP power. Average crystal grain sizes of single phase cubic (FCC) VN coatings were decreased from 10.1 nm to 4.0 nm with an increase in ICP power. The maximum hardness of 28.2 GPa was obtained for the coatings deposited at ICP power of 200 W. The smoothest surface morphology with Ra roughness of 1.7 nm was obtained in the VN coating sputtered at ICP power of 200 W.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.229-230
• /
• 2008

We have studied the structural and optical properties of ZnO thin film deposited on glass by RF magnetron sputtering as functions of working pressures. The grain sizes were decreased as the working pressures were increased. The average optical transmissions over all exceeded 80% for ZnO films deposited in 20, 25 and 300m torr working pressures. And the transmission spectra patterns were almost same. While the transmission spectra pattern of ZnO film deposited in 35nm torr was different with other spectra patterns obtained in 20, 25 and 30nm torr working pressures.

• Agricultural and Biosystems Engineering
• /
• v.5 no.2
• /
• pp.55-59
• /
• 2004

This study aimed to develop a seeder for sowing large seeds such as those of fruit vegetables used as rootstocks in grafting. It investigated how the nozzle diameter and the nozzle's vacuum pressure affected the seeding performance. This study found that a nozzle diameter of 1.5 mm was capable of sowing most of the seed sizes used in this study. The highest seeding rates for 'Chambak', 'Tuktozwa', and 'Hukjong' were $97.6\%$, $98.8\%$, and $97.6\%$, respectively. Lineup status after sowing was good. The working performance was 75.6 sheets/hr. An average seeding rate of 1 grain was $97.8\%$.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1298-1299
• /
• 2006

In the present work, the influence of the ball-milling time, milling atmosphere and weight ratio of ball to powder on characteristics of $WO_3-CuO$ was studied. Results show that, the grain sizes of the $WO_3$ and CuO in the ball-milled powder mixture were significantly decreased with increasing the milling time. Those of each oxide ball-milled in Argon and Hexane atmosphere for 30 and 20 hour were about 98 and 84 nm, respectively. After milling of 20 hour in Hexane as PCA, the powder had a homogeneously mixed structure and the average size of $WO_3-CuO$ powders was determined to about 230nm.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.1
• /
• pp.114-118
• /
• 2009

A new Zn/O single source precursor, TMEDA-Zn$(eacac)_2$, has been synthesized by using N, N, N’, N’-tetramethylethylendiamine (TMEDA), sodium ethyl-acetoacetate, and $ZnCl_2$. From this organometallic precursor, ZnO thin films have been successfully grown on Si (100) substrates through the metal organic chemical vapor deposition (MOCVD) method at relatively mild conditions in the temperature range of 390~430 ${^{\circ}C}$. The synthesized ZnO films have been found to possess average grain sizes of about 70 nm with an orientation along the c-axis. The precursor and ZnO films are characterized through infrared spectroscopy, nuclear magnetic resonance spectroscopy, EI-FAB-spectroscopy, elemental analyses, thermal analysis, X-ray diffraction, and field emission scanning electron microscopic analyses.

• The Korean Journal of Ceramics
• /
• v.5 no.2
• /
• pp.99-103
• /
• 1999

Compressive creep of dense polycrystalline $BaTiO_3$, with average grain sizes of 19.3-52.4$\mu\textrm{m}$, has been investigated at 1100-$1300^{\circ}C$ in air or under controlled atmospheres $(10^2-10^5Pa \;O_2)$. Some cavity growth occurred during deformation because of non-steady-state damage accumulation in the form of cavitation. Comparison of the creep data of polycrystalline BaTiO3 with existing diffusivity and creep data for perovskite oxides suggested that deformation of polycrystalline $BaTiO_3$ was controlled by the extrinsic lattice diffusion of barium or titanium.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.436-439
• /
• 2000

Change of dielectric loss of use in high relative permitivity capacitor BaTiO$_3$ ceramic depends on Mn doping have been investigated. The powders used in this study were commercial BaTiO$_3$, TiO$_2$and, MnCO$_3$. Sample was fabricated by conventional ceramic process. The quantity of Mn was changed gradually from 0.lmol% to 10mo1%. The sintering densities were reduced with increasing amount of MnCO$_3$. This result is because of increase of low density second phase BaMnO$_3$. When the samples were doped by over 0.2mol% of MnCO$_3$, average grain sizes were enlarge to several tens ${\mu}{\textrm}{m}$. The dielectric losses were reduced by Mn doping to lmol% but, increased from lmol% to 10mo1% gradually.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.739-742
• /
• 2000

Nanostructured ZnS thin films were grown on the slide glass substrate by the chemical bath deposition using an aqueous so1ution Of ZnSO$_4$and CH$_3$CSNH$_2$at 95$^{\circ}C$. The average grain sizes of the ZnS thin film estimating from the Debye-Scherrer formula are 4.8 nm. The optical transmittance edge of the ZnS thin films (4.0 eV) was shifted to the shelter wavelength compared with that of the bulk ZnS (3.67 eV) due to the quantum size effects. The ZnS thin films showed a strong photoluminescence intensity and a sharp emission band from 410 to 480 nm 3t room temperature. The PWHM of photoluminescence peak was about 40 nm. For the viloet(410 nm) and blue(480 nm) emission of the ZnS thin films, the temperature dependence can be described by an Arrhenius equation with an activation energy of 168 and 157 meV, respectively.

• Journal of the Korean institute of surface engineering
• /
• v.57 no.4
• /
• pp.348-354
• /
• 2024

Nanocrystalline zirconium nitride (ZrN) coatings were deposited by mid-frequency direct current sputtering (mfMS) with varying pulsed plasma parameters such as pulse frequency and duty cycle to understand the effect of pulsed plasma on the microstructure, residual stress and mechanical properties. The results show that, with the increasing pulse frequency and decreasing duty cycle, the coating morphology changed from a porous columnar to a dense structure, with finer grains. Mid-frequency magnetron sputtered ZrN coatings with pulse frequency of 30 kHz showed the highest both nanoindentation hardness of 16.3 GPa, and elastic modulus of 214.4 GPa. In addition, Effect of pulse frequency on a residual stress and average crystal grain sizes was also investigated.