• 한국세라믹학회지
• /
• 제24권1호
• /
• pp.9-16
• /
• 1987

Physical and electrical properties of ${\beta}$-Al2O3 were investigated as function of Na2O content from 6.67 wt.% to 13.19 wt.%. The majority phase is ${\beta}$-Al2O3 and the small amount of ${\beta}$"-Al2O3 exists in the specimens sintered at 1600$^{\circ}$for 30 mins. In the case of specimens with 8.54 wt.% Na2O sintered at 1600$^{\circ}C$, the relative amount of ${\beta}$-Al2O3 phase increases and that of ${\beta}$"-Al2O3 phase decreases with increasing sintering time, and then ${\beta}$"-Al2O3 phase does not exist if sintering time is over 8 hrs. As the Na2O content is increased, the 3-Point MOR and the resistivity are decreased. However, density and 3-Point MOR with increasing sintering time are decreased due to increasing the enclosed pore trapped inside of the exaggerated grains. As the sintering time is increased, the average grain size and the duplexity of microstructure are increased, and the resistivity is slightly decreased.

• 전기학회논문지
• /
• 제60권11호
• /
• pp.2093-2096
• /
• 2011

In this study, lead-free $(Na_{0.5}K_{0.5})NbO_3-BiTiO_3$ ceramics were fabricated by a conventional mixed oxide method. Structural and electrical properties of lead-free $(Na_{0.5}K_{0.5})NbO_3$ ceramics with the variation of $BiTiO_3$ were investigated. The results of X-ray diffraction analysis showed a typical polycrystalline perovskite structure without presence of the second phase in all specimens. Sintered density increased with an increasing of BTO and the specimen added with 0.07 mol% of $BiTiO_3$ showed the maximum value of 97.8%. Average grain size decreased and densification increased with an increasing of $BiTiO_3$ contents. The electromechanical coupling factor of the 0.01 mol% $BiTiO_3$ doped NKN specimens was 0.32. Dielectric constant, dielectric loss and Curie temperature of the 0.07 mol% $BiTiO_3$ doped NKN specimens were 1185, 0.145% and $400^{\circ}C$, respectively.

• 한국전기전자재료학회논문지
• /
• 제20권6호
• /
• pp.508-513
• /
• 2007

The electrical properties and stability of $ZnO-Pr_6O_{11}-CoO-Cr_2O_3-based$ varistors were investigated for different $Tb_4O_{11}$ amounts in the range of $0{\sim}1.0\;mol%$. As the $Tb_4O_{11}$ amount increased, the sintered density increased in the range of $99.1{\sim}101.1%$ of theoretical density and the average grain size decreased in the range of $7.7{\sim}4.8{\mu}m$. The varistor voltage increased in the range of $280.9{\sim}715.8V/mm$ and the nonlinear coefficient increased in the range of $26.4{\sim}44.4$ with the increased of $Tb_4O_{11}$ amount. The 0.25 mol% $Tb_4O_{11}$-doped varistors exhibited the high electrical stability, with -0.1% in variation rate of varistor voltage, -0.7% in variation rate of nonlinear coefficient, and +17.4% in variation rate of leakage current for specified dc accelerated aging stress of $0.95V_{1mA}/150^{\circ}C/24h$.

• 한국분말재료학회지
• /
• 제11권3호
• /
• pp.247-252
• /
• 2004

Recently, it has been found that mechanical alloying (MA) facilitates the nanocomposites formation of metal-metal oxide systems through solid-state reduction during ball milling. In this work, we studied the MA effect of Fe$_{3}$O$_{4}$-M (M = Al, Ti) systems, where pure metals are used as reducing agents. It is found that composite powders in which $Al_{2}$O$_{3}$ and TiO$_{2}$ are dispersed in $\alpha$-Fe matrix with nano-sized grains are obtained by mechanical alloying of Fe$_{3}$O$_{4}$ with Al and Ti for 25 and 75 hours, respectively. It is suggested that the large negative heat associated with the chemical reduction of magnetite by aluminum is responsible for the shorter MA time for composite powder formation in Fe$_{3}$O$_{4}$-Al system. X-ray diffraction results show that the reduction of magnetite by Al and Ti if a relatively simple reaction, involving one intermediate phase of FeAl$_{2}$O$_{4}$ or Fe$_{3}$Ti$_{3}$O$_{10}$. The average grain size of $\alpha$-Fe in Fe-TiO$_{2}$ composite powders is in the range of 30 nm. From magnetic measurement, we can also obtain indirect information about the details of the solid-state reduction process during MA.

• 한국분말재료학회지
• /
• 제17권6호
• /
• pp.464-469
• /
• 2010

The Cu nanofluid in ethylene glycol was prepared by electrical explosion of wire, a novel one-step method. The X-ray diffraction, field emission scanning electron microscope and transmission electron microscope were used to study the properties of Cu nanoparticles. The results showed that the nanoparticles were consisted of pure face-centered cubic structure and near spherical shape with average grain size of 65 nm. Ultraviolet-visible spectroscopy (UV-Vis) confirmed Cu nanoparticles with a single absorbance peak of Cu surface plasmon resonance band at 600 nm. The nanofluid was found to be stable due to high positive zeta potential value, +51 mV. The backscattering level of nanofluid in static stationary was decreased about 2% for 5 days. The thermal conductivity measurement showed that Cu-ethylene glycol nanofluid with low concentration of nanoparticles had higher thermal conductivity than based fluid. The enhancement of thermal conductivity of nanofluid at a volume fraction of 0.1% was approximately 5.2%.

• 한국분말재료학회지
• /
• 제14권4호
• /
• pp.251-255
• /
• 2007

This work is to report not only the effect of rapid solidification of $MgZn_{4.3}Y_{0.7}$ alloys on the micro-structure, but also the extrusion behavior on the materials properties. The average grain size of the atomized powders was about $3-4{\mu}m$. The alloy powders of $Mg_{97}Zn_{4.3}Y_{0.7}$, consisted of I-Phase (Icosahedral, $Mg_{3}Zn_{6}Y_{1}$) as well as Cubic structured W-Phase ($Mg_{3}Zn_{3}Y_{2}$), which was finely distributed within ${\alpha}-Mg$ matrix. The oxide layer formed along the Mg surface was about 48 nm in thickness. In order to study the consolidation behavior of Mg alloy powders, extrusion was carried out with the area reduction ratio of 10:1 to 20:1. As the ratio increased, fully deformed and homogeneous microstructure could be obtained, and the mechanical properties such as tensile strength and elongation were simultaneously increased.

• 한국가구학회지
• /
• 제22권4호
• /
• pp.323-329
• /
• 2011

In our country, domestic species can not be used as a structural member because we have not yet grading system. So, to utilize as a basic data of grading system, bending test and numerical modelling on structural member were conducted in this study. 35 of Douglas-fir, 2" ${\times}$ 6", span 2.4 m were tested for the bending properties, and Ansys software was used to analyze the numerical modelling on the structural members. The data of knots were inspected and applied in numerical modelling. To obtain the accuracy of analysis, nonlinear numerical analysis was carried out instead of linear numerical analysis. Ultimate load had a wide range from 4883N to 11,738 N, and maximum deformation also had a range from 26 mm to 68 mm. Average of ultimate load was 8,616 N, and that of maximum deformation was 48 mm. The distinctive features of failure types were simple tension type and cross-grain tension type. Ulitmate load and maximum deformation from numerical modelling were 7,504 N and 37 mm. The numerical modelling drawn by this study is available to all species, and reasonable prediction on the bending performance is possible with only some material properties.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.329-331
• /
• 2003

In this paper, $0.10Pb(Sb_{1/2}Sn_{1/2})O_3-0.25PbTiO_3-0.65PbZrO_3$ ceramics were fabricated by the mixed-oxide method. The sintering temperature and time were $1230^{\circ}C$ and 2(hr), respectively. The structural, dielectric and pyroelectric properties with addition of $Y_2O_3$ were studied. The crystal structure of a specimen was rhombohedral. As a result of SEM, the average grain size were decreased with increasing the contents of $Y_2O_3$. Relative dielectric constant and dielectric loss of the specimen doped with 0.2wt% $Y_2O_3$ were 597 and 0.022, respectively. Remanent polarization and coercive field of the specimen doped with 0.4wt% $Y_2O_3$ were $8.5[{\mu}C/cm^2]$ and 10.2[kV/cm], respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.307-308
• /
• 2005

ZnO varistor ceramics were fabricated as a function of the sintering temperature from $1125^{\circ}C$ to $1200^{\circ}C$ with glass-frit 0.03wt% addition. The average grain size was increased from 10.4 ${\mu}m$ to 23.7 ${\mu}m$, and varistor voltage was decreased from 538 V to 329 V with rising of the sintering temperature. The nonlinear coefficient a showed similar value from 75 to 80 and leakage current of all specimens exhibited the result of $1{\mu}A$ at 82% of varistor voltage. But the clamping voltage ratio of the specimens sintered at $1175^{\circ}C$ was 1.37 at 25A [$8/20{\mu}s$]. Also, endurance of surge current and deviation of varistor voltage of sintered specimens at $1175^{\circ}C$ were $6400A/cm^2$, $\Delta$-3.32%, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.382-383
• /
• 2006

The tungsten bronze type of strontium barium niobate(SBN) thin film was synthesized by metal organic decomposion method for SBN stock solution and the SBN thin film process were deposited by spin-coating process on Pt-deposited si-wafer(100) by magnetron sputtering system. The thickness of SBN thin film was 150~200 nm and were optimized for rpm of spin-coater system. The structural variation of SBN thin film was studied by TG-DTA and XRD. The deposited SBN stock solution on annealing at $400{\sim}800^{\circ}C$ a pure tungsten bronze SBN phase and the corresponding. average grain size about 500~1000 nm influenced by annealing temperature. The piezoelectric properties of prepared SBN thin film, the remanent polarization value(2Pr) and coercive field was $1.2{\mu}C/cm^2$ and 2.15V/cm, respectively.