• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.10
• /
• pp.65-77
• /
• 2004

In this paper, we propose an adaptive mechanism based on immune algorithm and neural network identifier technique. It is also applied fur an autonomous guided vehicle (AGV) system. When the immune algorithm is applied to the PID controller, there exists the case that the plant is damaged due to the abrupt change of PID parameters since the parameters are almost adjusted randomly. To solve this problem, we use the neural network identifier (NNI) technique fur modeling the plant and humoral immune algorithm (HIA) which performs the parameter tuning of the considered model, respectively. After the PID parameters are determined in this off-line manner, these gains are then applied to the plant for the on-line control using an immune adaptive algorithm. Moreover, even though the neural network model may not be accurate enough initially, the weighting parameters are adjusted to be accurate through the on-line fine tuning. Finally, the simulation and experimental result fur the control of steering and speed of AGV system illustrate the validity of the proposed control scheme. These results for the proposed method also show that it has better performance than other conventional controller design methods.

• The Journal of Korea Robotics Society
• /
• v.15 no.3
• /
• pp.221-232
• /
• 2020

In a four-wheel independent drive platform, four wheels and motors are connected directly, and the rotation of the motors generates the power of the platform. It uses a skid steering system that steers based on the difference in rotational power between wheel motors. The platform can control the speed of each wheel individually and has excellent mobility on dirt roads. However, the difficulty of the straight-running is caused due to torque distribution variation in each wheel's motor, and the direction of rotation of the wheel, and moving direction of the platform, and the difference of the platform's target direction. This paper describes an algorithm to detect the slip generated on each wheel when a four-wheel independent drive platform is traveling in a harsh environment. When the slip is detected, a compensation control algorithm is activated to compensate the torque of the motor mounted on the platform to improve the trajectory tracking performance of the platform. The four-wheel independent drive platform developed for this study verified the algorithm. The wheel slip detection and the compensation control algorithm of the platform are expected to improve the stability of trajectory tracking.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2007.04a
• /
• pp.3-6
• /
• 2007

전 세계적으로 차량의 급속한 증가로 인해 지능형교통시스템에 대한 연구가 활발히 진행 되고있다. 그중 차량의 자율주행에 관한 연구가 한 분야를 차지한다. 그리고 차량의 자율주행은 경로 인식이 기본적인 요소이다. 기존의 경로인식은 3축 자계 센서로 자석마커의 3차원의 데이터를 분석하여 인식하였다. 그러나 본 논문에서는 Magnetic Wire와 자기거리계를 이용하여 측면 이탈거리를 계측하여 주행하는 시스템을 제안한다. 그리고 기존 자율주행 차량의 시스템과 비교하고 제안하는 시스템이 저사양의 하드웨어와 간단한 알고리즘으로 자율주행이 가능함을 실험을 통해 검증하고자 한다.

• Proceedings of the KIEE Conference
• /
• 2003.07e
• /
• pp.38-41
• /
• 2003

An Autonomous Mobile Robot(AMR) performs duty by sensing a recognized situation and controlling suitably. The existing algorithm has some advantages that it is possible to express the obstacle exactly and the robot is sensitive to the change of environment. However, this algorithm needs to control repeatedly according to the modelling and working environment that requires a great quantity of calculations. In this paper, We supplement shortcoming and designed direction algorithm of AMR using fuzzy controller. Fuzzy controller does not derive special quality spinning expression for system, and uses rules by value expressed by language. It is used extensively to non-linear, plant which mathematical modelling is difficult etc... Fuzzy control algorithm of AMR that is used by this research applies obstacle position, distance of obstacle, Progress direction of robot, speed of robot, Perception area of sensor, etc... by fuzzy control and decide steering angle of robot.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.180.1-180
• /
• 2001

In the autonomous vehicle, the reference lane is continually detected by machine vision system. And then the vehicle is steered to follow the reference yaw rates which are generated by the deviations of lateral distance and the yaw angle between the vehicle and the reference lane. To cope with the steering delay and the side-slip of vehicle, PI controller is introduced for the yaw rate feedback. And it is tuned by the simulation that the vehicle is modeled as 2 DOF verified by the results of the actual vehicle test. The lateral control algorithm by the yaw rate feedback has good performances of lane tracking and passenger comfort.

• Journal of Mechanical Science and Technology
• /
• v.16 no.3
• /
• pp.338-343
• /
• 2002

In the autonomous vehicle, the reference lane is continually detected by machine vision system. And then the vehicle is steered to follow the reference yaw rates which are generated by the deviations of lateral distance and the yaw angle between a vehicle and the reference lane. To cope with the steering delay and the side-slip of vehicle, PI controller is introduced by yaw rate feedback and tuned from the simulation where the vehicle is modeled as 2 DOF and 79 DOF and verified by the results of an actual vehicle test. The lateral control algorithm by yaw rate feedback has good performances of lane tracking and passenger comfort.

• Journal of Navigation and Port Research
• /
• v.44 no.5
• /
• pp.423-429
• /
• 2020

A ship's automatic steering system is the basis for addressing control difficulties related to course-changing and course-keeping during navigation through heading angle control, and is a link in realizing unmanned and autonomous ships. This study proposes a robust RCGA-based linear active disturbance rejection controller (LADRC) design method considering environmental disturbances, measurement noise, and model uncertainties in designing a ship heading controller for use when the ship is sailing. The LADRC consisted of a transient profile, a linear extended state observer, and a PD controller. The control gains in the LADRC with the linear extended state observer were adjusted by RCGAs to minimize the integral of the time-weighted absolute error (ITAE), which is an evaluation function of the control system. The proposed method was applied to ship heading control, and its effectiveness was validated by comparing the propulsive energy loss between the proposed method and a conventional linear PD controller. The simulation results showed that the proposed method had the advantages of lower propulsive energy loss, more robustness, and higher tracking precision than the conventional linear PD controller.

• Journal of Biosystems Engineering
• /
• v.21 no.4
• /
• pp.422-428
• /
• 1996

This study was conducted to developed to develop a simple battery-powered autonomous vehicle for greenhouse works. A steering method using speed difference of two independent driving motors was adopted. DC motor driving circuit, speed control circuit and controller using one-chip microcomputer were constructed. The inputs of controller are rolling of the vehicle and current speed of driving motors. Using these signals, automatic guidance system along furrow was developed. A computer simulation program by the kenematic analysis was developed to find out optimal control algorithm. The results of this study are as follows. 1. Automatic guidance system along the furrow that adopted two independent driving motors and rolling of vehicle was developed. 2. The results of simulation showed that PID control was adequate to automatic guidance system along furrow. 3. Two commercial 12V battery serially connected were able to drive the vehicle on the soil ground for five hours in continuous operation and for four hours in intermittent operation without recharging the battery. 4. The speed range was 0-0.7m/s and the rolling of vehicle could be controlled within $pm5^{\circ}$ range. 5. From a series of tests, developed vehicle was found to be a useful tool for greenhouse works.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.2 s.63
• /
• pp.67-73
• /
• 2005

This paper describes depth, heading and speed control of an underwater vehicle that has four stern thrusters of which forces are coupled in the diving and, steering motion, as well as the speed of the vehicle. The optimal linear quadratic controller is designed based on a linearized- state space model, developed by combining the dynamic equations of speed, steering and diving motion. The designed controller gives provides an optimal thrust distribution, minimizing the given performance index to control speed, depth and heading simultaneously. To validate the performance of the controller, a simulation and tank-test are carried out with DUSAUV (Dual Use Semi-Autonomous Underwater Vehicle), developed by KORDI as a test-bed for testing new underwater technologies. Optimal gains of the controller are tuned, using a computer simulation environment with a nonlinear 6-DOF numerical DUSAUV model, developed by PMM (Planner Motion Mechanism) test. To verify the performance of the presented controller in experiment, a tank-test with DUSAUV is carried out in the ocean engineering basin in KORDI. The experimental results are also compared with the simulation results to investigate the accordance of the numerical and the real mode.

• The Journal of Korea Robotics Society
• /
• v.18 no.3
• /
• pp.299-307
• /
• 2023

In the midst of accelerating wars around the world, unmanned robot technology that can guarantee the safety of human life is emerging. ERP-42 is a modular platform that can be used according to the application. In the field of defense, it can be used for transporting supplies, reconnaissance and surveillance, and medical evacuation in conflict areas. Due to the nature of the military environment, atypical environments are predominant, and in such environments, the platform's path followability is an important part of mission performance. This paper focuses on reducing the minimum turning radius in terms of improving path followability. The minimum turning radius of the existing 2WS/2WD in-wheel platform was reduced by increasing the torque of the independent driving in-wheel motor on the rear wheel to generate oversteer. To determine the degree of oversteer, two GPS were attached to the center of the front and rear wheelbases and measured. A closed-loop speed control method was used to maintain a constant rotational speed of each wheel despite changes in load or torque.