• Korean Journal of Computational Design and Engineering
• /
• v.8 no.3
• /
• pp.189-200
• /
• 2003

This paper introduces the development of a three-dimensional jig design system for automotive body welding assembly. Recently, three-dimensional CAD systems have been introduced in the jig design area, because they reduce errors in design process and the design result can be used readily for virtual manufacturing simulation. However, to facilitate three-dimensional jig design, it is essential to customize three-dimensional CAD system for this specific design area. To accomplish this object, we first standardized the parts and units in a jig assembly, and then built the standard part library. We also developed the dedicated 3D design capabilities of jig units and a jig base. By using this system, design can be performed more intuitively, and verification and simulation of design results can be done more easily. The proposed system has been implemented using the UG/Open API of the Unigraphics system.

• Journal of KSNVE
• /
• v.5 no.4
• /
• pp.503-514
• /
• 1995

In the case of performing experimental modal analysis(EMA) and finite- element analysis(EFA) for a whole structure of automotive body that is composed of many complex parts, a trouble may arise from the calculation time, the capacity of memory in computers and the experimental conditions, etc. In this paper, for the vibrational analysis of automotive body model, the efficient modal synthesis method by means of dividing the whole structure into two parts and performing EMA and FEA for each part is studied. In addition, the method based on Lagrange interpolation is proposed for approximating rotational degrees-of-freedom information and linking FEA with EMA. In result, by measuring translational degrees-of-freedom information of only few points and adopting only few modes, the linking method based on Lagrange interpolation turned out to be efficient and accurate in the low frequency range.

• Transactions of Materials Processing
• /
• v.9 no.6
• /
• pp.624-630
• /
• 2000

Typical automotive opening parts, i. e. hood trunk lid and door, are made through the press operations such as drawing, trimming, flanging, and hemming. The dimensional accuracy of stamped panels is mainly dependent on the drawing operation. However, the gap between outer panels and opening parts, which is important to the appearance quality of the assembled body, is directly influenced by the flanging and hemming operation. In this study, the relation between the design parameters of the hemming operation and the defect of roll-in is shown. The effects of some design parameters on the gap are examined using CAE. furthermore, the simulated results of the hemmed part of tailgate comer are shown and discussed.

• Korean Journal of Computational Design and Engineering
• /
• v.16 no.5
• /
• pp.323-330
• /
• 2011

Large number of part design such as for aircraft and automotive development is preceded by functional or sectional design groups for efficiency. With the assembly development of large number of parts, interferences and gaps can be found when the parts and sub-assemblies by those design groups are to be assembled. When rainwater come into the space among parts and is not be drained sufficiently, rainwater within the structure can backflow to gaps or unexpected outlets, which may cause severe problems of part corrosion and electric shock. This research has developed a method and a program to simulate backflow of rainwater within space among parts, which can find unexpected outlets and gaps as in real situation. The developed program can not only simulate up and downstream of liquid, but also the flow with multiple channels of division and joining. The developed method can also be applied to aircraft and ship design process.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.1
• /
• pp.105-112
• /
• 2011

Increasing needs for light weight and high safety in modern automobiles induced the wide application of high strength steels in automotive body structures- The main difficulty in the forming of sheet metal parts with high strength steel is the large amount of springback including sidewall curl and twist in channel shaped member parts- Among these shape defects, twist occurs frequently and requires numerous reworks on the dies to compensate the shape deviation- But until now, it seems to be no effective method to reduce the twist in the forming processes- In this study, a new forming process to reduce the twist deformation during the forming of automotive structural member was suggested- This method consists of forming and restriking of embosses on the sidewall around the stretch flanging area of the part- and was applied in the forming process design of an automotive front side inner member with high strength steel- To evaluate the effectiveness of the method, springback analysis using $Pamstampa^{tm}$ was done- Through the analysis results, the suggested method was proven to be effective in twist reduction of channel shaped parts with stretch flanging area.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.1
• /
• pp.153-158
• /
• 2005

Titanium alloy has widely been used as material for automotive parts because it has high specific strength. It is also light and harmless to human body. But, we have little design data about the creep behaviors of the alloy. Therefore, in this study, creep tests under four constant stress conditions have been conducted with low different temperature conditions. A series of creep tests had been performed to get the basic design data and life prediction of titanium products and we have gotten the fallowing results. First, the stress exponents decrease as the test temperatures increased. Secondly, the creep activation energy gradually decrease as the stresses became bigger. Thirdly, the constant of Larson-Miller parameter on this alloy was estimated as about 7.5. And for the last, the fractographs at the creep rupture showed the ductile fracture due to the intergranullar rupture.

• Journal of Sensor Science and Technology
• /
• v.33 no.3
• /
• pp.179-184
• /
• 2024

In the car industry, welding is a fundamental linking technique used for joining components, such as steel, molds, and automobile parts. However, accurate inspection is required to test the reliability of the welding components. In this study, we investigate the detection of weld beads using 2D image processing in an automatic recognition system. The sample image is obtained using a 2D vision camera embedded in a lighting system, from where a portion of the bead is successfully extracted after image processing. In this process, the soot removal algorithm plays an important role in accurate weld bead detection, and adopts adaptive local gamma correction and gray color coordinates. Using this automatic recognition system, geometric parameters of the weld bead, such as its length, width, angle, and defect size can also be defined. Finally, on comparing the obtained data with the industrial standards, we can determine whether the weld bead is at an acceptable level or not.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.322-325
• /
• 2007

Dent resistance is an important characteristic to avoid damage on automotive outer panels. From a practical point of view, dents can be caused in a number of ways. Considering doors as an example, denting can occur from stone impacts or from the careless opening of an adjacently parked vehicle door. Denting can occur where the door surface is smooth and may not have sufficient curvature to resist dent. These exterior body parts are designed to improve dent resistance using a combination of work hardening and bake hardening. In brief, dent is affected by the shape of the parts and the material properties such as yield strength, strain and thickness. In this work, forming of door outer panel is investigated by Taguchi method. Main parameters are yield strength, thickness, blank size, blank holding force and so on. For the given value of design parameters, forming analysis of the thirty six cases are carried out according to L18 orthogonal array. After comparing the performance by simple conversion of simulation results into dent resistance, the final suggestion of the forming parameters is verified for the best improvement of dent resistance.

• Korean Journal of Materials Research
• /
• v.21 no.7
• /
• pp.364-370
• /
• 2011

Currently, there are two main issues regarding the development of core technologies in the automotive industry: the development of environmentally friendly vehicles and securing a high level of safety in the event of an accident. As part of the efforts to address these issues, research into alternative materials and new car body manufacturing and assembly technologies is necessary, and this has been carried out mainly by the automotive industries. Large press molds for producing car body parts are made of cast iron. With the increase of automobile production and various changes of design, the press forming process of car body parts has become more difficult. In the case of large press molds, high hardness and abrasive resistance are needed. To overcome these problems, we attempted to develop a combined heat treatment process consisting of local laser heat treatment followed by plasma nitriding, and evaluated the characteristics of the proposed heat treatment method. From the results of the experiments, it has been shown that the maximum surface hardness is 864 Hv by the laser heat treatment, 953 Hv by the plasma nitriding, and 1,094 Hv by the combined heat treatment. It is anticipated that the suggested combined heat treatment can be used to evaluate the durability of press mold.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.6
• /
• pp.29-34
• /
• 2017

This study analyzed automobile lower arm assembly structure and fatigue to identify configuration changes to enhance structural safety. Parts connected to the car body were fixed and 500 N load was applied at the lower arm head. Maximum equivalent stress and maximum total deformation were minimized for model 1 ( MPa and 0.10315 mm, respectively). Fatigue analysis using extreme SAE bracket history fatigue loads showed model 1 also improved fatigue life ($3.3693{\times}10^5cycles$). This study provides important inputs to improve lower arm durability by modifying the arm configuration.