• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.1
• /
• pp.55-60
• /
• 2004

Residual gas acts as a diluent which results in reducing the in-cylinder temperature as well as the flame speed, significantly affecting fuel economy, NOx emissions and combustion stability. Therefore it is important to determine the residual gas fraction as a function of the engine operating parameters accurately. However, the determination of the residual gas fraction is very sophisticated due to the unsteady state of induction and exhaust process. There has been little work toward the development of a generally applicable model for quantitative predictions of residual gas fraction. In this paper, a simple model for calculating the residual gas fraction in SI engines was suggested. The amount of fresh air was evaluated through AFR and fuel consumption. After this, from the intake temperature and pressure, the amount of total cylinder-charging gas was estimated. The residual gas fraction was derived by comparing the total charging and fresh air. This results coincide with measured EGR value very well.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.6
• /
• pp.142-154
• /
• 1998

The effects of recirculated exhaust gas on the characteristic of soot emissions have been investigated by using an eight-cylinder, four-stroke, direct injection and water-cooled diesel engine operating at several loads and speeds. The experiments in this study are carried out at the fixed fuel injection timing of $38^{\circ}$ BTDC regardless of experimental conditions. The intake oxygen concentration and the mean equivalence ratio calculated by the intake air flow and fuel consumption rate are used to analyze and discuss the influences of EGR rate on soot emissions. Results of this study indicate that soot emissions increase owing to the drop of intake oxygen concentration and the rise of equivalence ratio as the EGR rate increases at a given engine load and speed, especially the high load.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.6
• /
• pp.18-28
• /
• 1994

An exhaust-heated gas turbine cycle equipped with a waste heat recovery boiler and ammonia absorption-type refrigerator using waste heat is newly devised and analyzed. The general performance of this cycle is compared with that of the conventional gas turbine cycle. This cycle shows a potential high efficiency. When 1500K of gas turbine inlet temperature the efficiency is 53 percent as compared to 45 percent for a conventional combined cycle. Suction cooling of this cycle leads to improve the thermal efficiency and the specific output.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.1
• /
• pp.74-81
• /
• 2016

The aim of this study was to find the initial design value of turbine blade for electrical type turbocompound system generating 10 kW. Turbocompound is one of the waste heat recovery system applying to internal combustion engine to recover exhaust gas energy that was about 30 % of total input energy. To design the turbine blade, 1-D mean line flow model was used. Exhaust gas temperature, pressure, flow rate and turbine rotating speed was fixed as primary boundary conditions. The velocity triangles was defined and used to determine the rotor inlet radius and width, the rotor outlet radius at shroud and radius at hub, the rotor flow angles and the number of blades.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.1
• /
• pp.61-65
• /
• 2004

This paper presents the effect of methanol blended fuel on the engine performance and the reduction of exhaust emissions. In this wort, the combustion effects of methanol blended fuel in the engine was investigated for the conditions of three kinds of mixing ratios. Based on the experimental results, the output characteristics of the engine show the improvement of output performance due to the blended fuel of methanol. Also, the unburned hydrocarbon and carbon monoxide emissions are decreased in accordance with the increase of methanol blended ratio.

• Journal of the korean Society of Automotive Engineers
• /
• v.13 no.3
• /
• pp.25-31
• /
• 1991

The formation process of hydrocarbon emissions was investigated in SI engine. The time- resolved concentrations of hydrocarbon emissions were measured using a high gas sampling valve and a gas chromatography. The gas was sampled at exhaust port, or the position of spark plug, or the wall of combustion chamber. The experiments were conducted using the Alpha engine of Hyundai Motor Company. The fuel used was methanol or propane. It was found that the effect of the quenching layer of combustion chamber wall on hydrocarbon emissions was not significant. The increasing rate of hydrocarbon concentration at combustion chamber wall near crevice and oil layer after flame was reached was much higher than that at the position of spark plug. The hydrocarbon concentrations at exhaust port had two peak values just after opening exhaust valve and just before closing it.

• Journal of Mechanical Science and Technology
• /
• v.17 no.10
• /
• pp.1563-1571
• /
• 2003

A fast response NO analyzer was applied to investigate the relation between cycle-by-cycle NO emissions and combustion chamber pressure. NO emissions were sampled at an isolated exhaust manifold of 4-stroke spark ignition engine to avoid the interference of exhaust gas from other cylinders. The linear correlation analysis was performed with collected data of NO emissions and combustion chamber pressure with respect to the various air-fuel mixture ratios and engine loads. The sampled data sets were obtained during 200 cycles at each operating condition. The results showed that there was a typical pattern in NO emissions from an exhaust port through a cycle. It was possible to set a block of crank angle in which the linear correlation coefficient between NO emissions and combustion chamber pressure was high. As the engine load increased, NO emissions were more dependent on combustion chamber pressure after TDC. It was also analyzed that the correlation between two parameters with respect to air-fuel mixture ratio tended to increase as mixture went leaner. Furthermore, this correlation coefficient for the mixture near the lean limit seemed to be kept high even though combustion was unstable.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.5
• /
• pp.35-43
• /
• 2014

The automobile industry requires technological innovations to reduce fuel consumption with the public interest in environmental conservation in recent years. Thus, the hybrid system is applied not only to passenger cars but also commercial vehicles. The purpose of this paper is to develop engine ECU_ILS to develop commercial hybrid vehicles. In order to develop the engine and vehicle, the dynamometer and exhaust gas analyzer is needed. However, a lot of time and cost are required. In contrast, the model-based development environment that can be applied to a variety of test conditions can reduce development time. Therefore, a HILS system environment that can consider the behavior of actual vehicles for evaluation of the control logic, fuel consumption and exhaust gas is required. This engine ECU_ILS system was developed in this study, can analyze parameter such as the fuel injection rate, fuel injection time, fuel consumption and exhaust gas like the actual vehicle test using map data. Also, this system is expected to be able to analyze the characteristic of vehicle behavior and the development of peripheral device in relation to engine and vehicles. This HILS system can be used to develop control strategies of commercial hybrid vehicle systems in the future.

• Journal of the korean Society of Automotive Engineers
• /
• v.11 no.5
• /
• pp.1-12
• /
• 1989

This short report describes the trend of exhaust emission control of the diesel engine vehicles in Korea, which originally was motivated from the newly proposed Emission Control Regulation of Diesel Engine Vehicles possible to be activated in 1991 by Korean Environmental Protection Agency. This short survey report has been prepared by the special working group of The Korea Society of Automotive Engineers (KSAE) on this particular subject. This report includes (1) estimation of portions of contribution of diesel engine vehicle emission to total air pollution, (2) comparison of proposals of new articles/regulations/laws in Korea with those of other selected countries such as USA, European countries, and Japan, (3) comparison of vehical emission control regulations in Korea with those in other selected countries, (4) technical aspects of possibilities of reduction of diesel engine vehicle emissions, (5) additional administrational aspects of technology development program, (6) social impact resulted from the severe emission control regulation on diesel engine vehicles, and (7) proposals, prepared by the special working group of the KSAE, on the emission control regulation of diesel engine vehicles, which can possibly bring better cleaner air released from the air pollution resulted from diesel engine exhaust emissions in real sense with minimal financial contribution, with optimal technological efforts, with less social impacts, within five to ten year period.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.4
• /
• pp.1192-1196
• /
• 2010

As the space for installation of automotive exhaust system is limited, the space should be optimized with relation to the endurance and shape of the system. Geometric nonlinear analysis was used and deflection of bellows was assumed 6mm. Obtained results are as follows; (1) The Von-Mises stress of bellows is increased with increase of thickness or radius of bellows linearly. (2) As the principal stress varies according to the radius of convolution, it is necessary to decide the optimal radius of convolution.