• 한국자동차공학회논문집
• /
• 제9권1호
• /
• pp.94-101
• /
• 2001

In this paper, the combustion improvement effects of alcohol-diesel oil blend fuel were investigated in a visualization engine. As a result of experiment, it was found out that the combustion chamber of deep dish type and re-entrant type at the same operation condition. However, when the con-tent of alcohol exceeded 10% of total fuel delivery, the combustion of alcohol-diesel oil blend fuel was worse than that of diesel oil. The maximum blend quantity of ethanol which is not ignited in the re-entrant type combustion chamber was estimated at approximately 40% of total fuel delivery. So, it is necessary to blend appropriate quantity of a volatility fuel such as alcohol in order to improve combustion.

• Tribology and Lubricants
• /
• 제25권5호
• /
• pp.318-323
• /
• 2009

The oil characteristics and wear particles of Diesel engines with a DPF have been investigated as a function of a driving distance. The engine oil of SAE 5W30 with ACEA C3 is used for an oil film lubrication of the engine, which is equipped with Diesel particulate filter. Depending on the oil test results, the kinematic viscosity of used engine oils at 40 is degraded up to 5.1% compared with that of unused engine oils, SAE 5W30. And the kinematic viscosity of used engine oils at 100 is more degraded up to 8.1% compared with that of unused engine oils. The oil characteristic as a function of a mileage is not changed depending on the driving distance because of high quality of engine oils. But the aluminum and copper compounds, which are used as base materials of the engine bearing and a pin bush, are much worn and contaminated for the increased mileage of the car. The oil properties of used engine oils are relatively good except phosphorus and calcium additives, which are heavily engaged in the performance of the oils.

• 한국자동차공학회논문집
• /
• 제9권3호
• /
• pp.42-50
• /
• 2001

In this paper, the effects of scale formation in engine water jacket upon the thermal durability of engine itself and its component parts were studied. To understand the effect of quality of water, a full load engine endurance test for 50 hours was carried out with not-treated underground water. The followings were found through the tested engine inspection after the endurance test; 1-2 mm thick scale formation in the engine water jacket, valve seat wear, piston top land scuffing, piston pin stick, and cylinder bore scuffing in siamese area. In order to understand the causes of above test results, the heat rejection rate to coolant, the metal surface temperature of combustion chamber, and the oil and exhaust gas temperatures were measured and analyzed. The scale formed in the engine water jacket played a role as thermal insulator. The scale formed in the engine reduced the heat rejection rate to coolant and it caused to increase the metal surface temperature. The reduced heat rejection rate to coolant increased the heat rejection rate to oil and exhaust gas and increased the oil and exhaust gas temperature. Also, the reasons of valve seat wear, piston top land scuffing and cylinder bore scuffing, and piston pin stick quantitatively analyzed in this paper.

• Tribology and Lubricants
• /
• 제30권3호
• /
• pp.156-167
• /
• 2014

This paper presents the test results of small dipstick-gage-type engine-oil-deterioration-detection sensor. The measured sensor signal characteristics for the capacitance and temperature are analyzed. The engine oil deterioration condition correlates with the electrical property of the dielectric constant that comprised with physical properties such as TAN (Total Acid Number), TBN (Total Base Number) and viscosity. Several problems encontered during the test of the sensor system are improved. The results of vehicle tests show that the capacitance signal is stable after the engine stops. Therefore, the sensor should start measuring the parameters for monitoring the engine oil condition after the engine stops. The engine is considered to be in a stopped state if the difference between the maximum and minimum values of the oil capacitance measured every 1 min is below 0.02 pF. The key test results in this paper will help in the development of an engine oil change warning algorithm.

• 한국자동차공학회논문집
• /
• 제5권3호
• /
• pp.147-158
• /
• 1997

This paper presents the analysis technique and procedure of main engine components-cylinder block, cylinder liners, gasket and cylinder head-using the finite element method, which aims to assess mainly the potential of lower oil consumption in a view point of engine design and to decide subsequently the accuracy of engine design which was done. The F.E. model of an engine section consisting of one whole cylinder and two adjacent half cylinders is used, whereby the crankcase is cut off at the block bottom deck. By means of a 3-dimensional F.E. model-including cylinder block, liners, gasket, cylinder head, bolts and valve seat rings as separate parts a linear analysis of deformations and stresses was performed for three different loading conditions;assembly, thermal and gas loads. For the analysis of thermal boundary conditions also the temperature field had to be evaluated in a subsequent step.

• 오토저널
• /
• 제11권4호
• /
• pp.19-29
• /
• 1989

• Tribology and Lubricants
• /
• 제26권2호
• /
• pp.111-121
• /
• 2010

The purpose of this study is to examine the effect of diesel soot contents on the deterioration of engine oil in terms of the changes in the dielectric constants of diesel engine oils. Therefore, it is figured out the level of oil deterioration by investigating how are the dielectric constants of diesel engine oils changed according to changes in diesel soot contents. The measured data will be able to be used as the reference data to judge the level of oil deterioration induced by diesel soot when the previously developed oil deterioration sensor will be applied at diesel vehicles in the future.

• Tribology and Lubricants
• /
• 제22권5호
• /
• pp.260-268
• /
• 2006

The dielectric constants of used gasoline engine oils were obtained at a few temperatures and a frequency. Through analyzing the characteristics of dielectric constant, the related correlation between the changes in dielectric constants of oil and the degree of oil deterioration is going to be found. The dielectric constant was calculated using cross capacitances measured by a sensor tube. As results of the measurement of the fresh engine oil's dielectric constant, it was found that the value of dielectric constant was set down below $60^{\circ}C$ regardless changing frequency. Further, above 6 kHz, the dielectric constant was set down even if temperature was above $100^{\circ}C$ Therefore, for the measurement of used oils, it was selected the frequency of 6 kHz,,and the temperature of $80^{\circ}C$ preventing a certain ionic-conduction effects on the measured dielectric constant and the evaporation of a certain fluid mixed with engine oil. Specially, the effects of the mixing fluid like coolant, water and fuel on the fresh engine oil's dielectric constant were studied. It was found that the oil mixed with coolant showed the highest value, next water, and the lowest fuel. As results of the measurement of the used engine oil's dielectric constant, it was found that the possible changed rate of the used engine oil's dielectric constant based on the warning limit for engine oil in service was below 4% for gasoline engine oil.

• Tribology and Lubricants
• /
• 제22권5호
• /
• pp.290-300
• /
• 2006

The dielectric constants of used diesel engine oils were obtained at a few temperatures and a frequency. Through analyzing the characteristics of dielectric constant, the related correlation between the changes in dielectric constants of oil and the degree of oil deterioration is going to be found. The dielectric constant was calculated using cross capacitances measured by a sensor tube. As results of the measurement of the fresh engine oil's dielectric constant, it was found that the value of dielectric constant was set down below $60^{\circ}C$ regardless changing frequency. Further, above 6 kHz, the dielectric constant was set down even if temperature was above $100^{\circ}C$. Therefore, for the measurement of used oils, it was selected the frequency of 6 kHz, and the temperature of $80^{\circ}C$ preventing a certain ionic-conduction effects on the measured dielectric constant and the evaporation of a certain fluid mixed with engine oil. Specially, the effects of the mixing fluid like coolant, water and fuel on the fresh engine oil's dielectric constant were studied. It was found that the oil mixed with coolant showed the highest value, next water, and the lowest fuel. As results of the measurement of the used engine oil's dielectric constant, it was found that the possible changed rate of the used engine oil's dielectric constant based on the warning limit for engine oil in service was below 10% for diesel engine oil.

• International Journal of Automotive Technology
• /
• 제7권3호
• /
• pp.245-249
• /
• 2006

Accelerated aging of engine exhaust system components such as catalytic converters are traditionally performed using an engine/dynamometer test stand. $SwRI^{(R)}'s\;FOCAS^{(R)}$ system reduces or eliminates many of the engine based aging limitations. This paper will describe several studies. These include: 1) replication of engine based catalyst aging cycles with added precision and dependability; 2) catalyst aging with and without lubricating oil effects; 3) effects of lubricant phosphorus on catalyst performance; and 4) the potential to thermally age components beyond the capabilities of engine based systems. The first study includes the development of the SwRI FOCAS system to run programmed aging conditions with or without lubricating oil. A description of the subsystems is given. The second two studies used the SwRI FOCAS system to age catalysts. One study compared thermal-only aging using of the SwRI FOCAS system with equivalent aging on a traditional engine/dynamometer test stand. The other study examined the effect on catalyst performance of two lubricating oils containing different levels of phosphorus, and compared the results to field data generated using the same oils in a fleet of vehicles.