• Journal of the Korean Institute of Gas
• /
• v.10 no.2 s.31
• /
• pp.33-39
• /
• 2006

For the safety design and operation of many gas process, it is necessary to know certain explosion limit, flash point, auto ignition temperature and minimum oxygen concentration of handling substances. Also it is necessary to know explosion limit at high temperature and pressure. For the safe handling of propane, explosion limit and autoignition temperature of combustion characteristics for propane were investigated. By using the literatures data, the lower and upper explosion limits of propane recommended 2.0 vol% and 10.0 vol%, respectively. Also autoignition temperatures of propane with ignition sources recommended $450^{\circ}C$ at the electrically heated cruicible fumace(the whole surface heating) and recommended about $960^{\circ}C$ at the local hot surface. The new equations for predicting the temperature and the pressure dependence of the explosion limits of propane are proposed. The values calculated by the proposed equations were a good agreement with the literature data.

• Journal of the Korean Institute of Gas
• /
• v.15 no.3
• /
• pp.39-46
• /
• 2011

This study investigates the effects of the DME and n-Butane mixture and of the stratification on combustion characteristics of HCCI engine by chemical reaction calculation. First, the existing DME reaction scheme and n-Butane is combined to make new chemical reaction model, then validating the effectiveness of new scheme. Furthermore, this study verify the HCCI combustion characteristics according to the changes of DME and n-Butane mixture ratio, which shows different auto ignition characteristics. Finally, it confirms the effects of stratification of mixture fuel on the reduction of pressure rise rate.

• Fire Science and Engineering
• /
• v.23 no.1
• /
• pp.21-32
• /
• 2009

In order to inspect the danger of forest fires, the thermal characteristics and the ignitability of the dead leaves and the living leaves for the main species of trees in Youngdong areas have been studied by the TG/DTA and the group flammability tester. From this work, the thermal delay has been increased with the increase of the heating rate. The fractions of the thermal weight loss for the dead leaves and the living leaves of the coniferous trees were higher than those of the broadleaf trees. Also, it was confirmed that the ignitable dangers of the dead leaves and the coniferous trees were higher than those of the living leaves and the broadleaf trees, due to the low auto ignition temperature and thermal resistance.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.1
• /
• pp.48-54
• /
• 2004

The purpose of this work is to investigate the effect of premixing condition on the combustion and exhaust emission characteristics in a HCCI diesel engine. To from homogeneous charge before intake manifold, the premixed gasoline fuel is injected into a premixed tank by fuel injection system and the premixed gasoline fuel is ignited by direct injected diesel fuel. Experimental result shows the NOx and soot emissions are decreased linearly with the increase of premixed ratio. In the case of intake air temperature $20^{\circ}C$ with light load, the specific fuel consumptions are increased with the rise of premixed ratio and HC and CO emissions are also increased. But the intake air heating can improve the specific fuel consumption at light load condition because increased air temperature promotes the combustion of premixed mixture. In the case of high intake air temperature with high load condition, premixed fuel is auto-ignited before diesel combustion and soot emission is increased.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.65-70
• /
• 2001

OH radical and NOx have been measured in a methane-air partially premixed flame using PLIF technique to define preheated air combustion characteristics. The temperature of mixture is determined by 300K, 400K, 600K and 800K below the auto-ignition temperature respectively. Flame height increases as equivalence ratio increased. As initial enthalpy is supplied, the radius of flame was increased and much amount of yellow flame in rich equivalence ratio was observed. This is due to the faster burning velocity. Also initial oxidization begins earlier as the initial temperature of mixture increased. It means that height of premixed flame front decreased. This phenomenon can be observed OH PLIF image. The qualitative analysis of OH concentration in the PLIF image shows that overall OH concentration increases with equivalence ratio and the initial temperature of mixture increased. At the preheating temperature goes up, axial gradient of OH concentration is less steep than that of lower temperature condition. This may identify that combustion reacts continuously, so preheated air combustion can evade the local heating and make high temperature indiscriminately in the overall reaction zone.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.2
• /
• pp.22-28
• /
• 2005

Exhaust gas emissions from internal combustion engines are one of the major sources of air pollution. And, it is extremely difficult to increase gasoline engine efficiency and to reduce $NO_X$ and PM(particulate matter) simultaneously in diesel combustion. This paper offers some basic concepts to overcome the above problems. To solve the problems, a recommended technique is CAI(controlled auto-ignition) combustion. In this paper, a flame trap was used to simulate internal EGR(exhaust gas recirculation) effect. An experimental study was carried out to find combustion characteristics using homogeneous premixed gas mixture in the constant volume combustion chamber(CVCC). Flame propagation photos and pressure signals were acquired to verify the flame trap effect. The flame trap creates high speed burned gas jet. It achieves higher flame propagation speed and more stable combustion due to the effect of geometry and burned gas jet.

• Journal of the Korean Institute of Gas
• /
• v.15 no.2
• /
• pp.82-87
• /
• 2011

Heat transfer oils are used in applications such as heating systems of chemical plant, refinery heat exchange systems, gas plant process, injection molding systems, and pulp and paper processing. These oils are extremely stable and resistance to thermal and oxidative degradation. In the event of a spill or accidental release of heat transfer oils, it can be ignite easily when there is an ignition source. This paper discusses the flammability and thermal stabilities of new and used oils. The flammability of the oils are assessed by measuring changes in flash point and auto ignition temperature. The thermal stability of oils are evaluated by the thermal screening unit ($TS^u$) and the differential scanning calorimeter (DSC). From the experimental results, it is suggested to give fire hazard characteristics to safe precautions for the proper use and treatment of heat transfer oils.

• Journal of the Korean Institute of Gas
• /
• v.14 no.6
• /
• pp.7-14
• /
• 2010

This study investigated the effect on reducing the pressure rise rate(PRR) in HCCI Engine by the variation of mixing ratio in the pre-mixture of DME and n-Butane that has different auto-ignition characteristics. In addition to measure of gas pressure in the engine cylinder, chemiluminescence image using the optical accessible engine and numerical analysis with multi-zones model were used to assess the combustion at each local area in the combustion chamber. The maximum PRR changes depending on mixing condition of DME and n-Butane. When DME is stratified and n-Butane is distributed uniformly, maximum PRR becomes lowest which is about 0.25MPa/ms and it corresponds to 5deg. retarding of CA50.

• Journal of the Korean Society of Safety
• /
• v.34 no.1
• /
• pp.27-33
• /
• 2019

Combustion characteristics of gasoline/ethanol fuel were investigated both numerically and experimentally for vehicle fire safety. The numerical simulation was performed on the well-stirred reactor (WSR) to simulate the homogeneous gasoline engine and to clarify the effect of ethanol addition in the gasoline fuel. The simulating cases with three independent variables, i.e. ethanol mole fraction, equivalence ratio and residence time, were designed to predict and optimized systematically based on the response surface method (RSM). The results of stoichiometric gasoline surrogate show that the auto-ignition temperature increases but NOx yields decrease with increasing ethanol mole fraction. This implies that the bioethanol added gasoline is an eco-friendly fuel on engine running condition. However, unburned hydrocarbon is increased dramatically with increasing ethanol content, which results from the incomplete combustion and hence need to adjust combustion itself rather than an after-treatment system. For more tangible understanding of gasoline/ethanol fuel on pollutant emissions, experimental measurements of combustion products were performed in gasoline/ethanol pool fires in the cup burner. The results show that soot yield by gravimetric sampling was decreased dramatically as ethanol was added, but NOx emission was almost comparable regardless of ethanol mole fraction. For soot morphology by TEM sampling, the incipient soot such as a liquid like PAHs was observed clearly on the soot of higher ethanol containing gasoline, and the soot might be matured under the undiluted gasoline fuel.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.1
• /
• pp.37-45
• /
• 2010

Computational simulation has been carried out to examine the effects of pilot injection to reduce both of NOx and Soot emissions in a marine diesel engine. For verification of the computational result, calculated cylinder pressure was matched to experimental pressure. In this study, the primary variables were injection timing, dwell time and injection rate while the amount of injection fuel was maintained constant. It was revealed that variation of pilot injection timing affects auto ignition and heat release rate. In the results, both of NO and soot emission were reduced without deterioration of in-cylinder pressure under the condition of $10^{\circ}$CA dwell time and 0.022kg/s injection rate.