• Journal of the Korean Society for Heat Treatment
• /
• v.28 no.3
• /
• pp.139-145
• /
• 2015

Effects of austenitizing, cryogenic treatment and tempering conditions on the phase change, microstructure and Vickers hardness value have been studied in STD11 steel for tool and die. The volume fraction of retained austenite increased with a rise in austenitizing temperature, while the volume fraction of eutectoid $M_7C_3$ carbides decreased. The retained austenite could be reduced by cryogenic treatment i.e., maintaining at $LN_2$ temperature ($-196^{\circ}C$) for 12hrs but a little amount of retained austenite did not transform to martensite further although holding time increased to 24 hrs or more. The microstructure of the quenched and then cryogenictreated specimen showed nano-sized and needle-shaped carbides in matrix due to the decomposition of martensite by tempering, but that of the one without cryogenic treatment still revealed retained austenite by tempering even at $500^{\circ}C$.

• Journal of the Korean Society for Heat Treatment
• /
• v.26 no.3
• /
• pp.120-125
• /
• 2013

In this study, the effect of tempering treatment on the mechanical properties in modified 440A steel has been investigated. The amount of remaining carbide decreased with increasing the austenitizing treatment temperature, and all carbides were completely dissolved at $1250^{\circ}C$. The amount of remaining carbide decreased with increasing the time of austenitizing, but the carbide remained insoluble up to 120 minutes at $1050^{\circ}C$. With increasing the tempering temperature, tensile strength decreased, and elongation increased slowly, while hardness rapidly decreased, and impact value unchanged and then rapidly increased over $500^{\circ}C$. The strength and hardness slowly decreased, while the elongation and impact absorbed energy increased with increasing the tempering time. $Cr_{23}C_6$ type carbide was precipitated and sharp decrease of elongation and toughness by tempering did not appear.

• Journal of the Korean Society for Heat Treatment
• /
• v.24 no.6
• /
• pp.327-337
• /
• 2011

Effects of microstructural change, tensile properties and impact property according to the change of austenitizing temperature and tempering temperature of AISI 51B20 steel were examined. Regardless of austenite grain size, lath martensite with needle and packet shapes was found at tempering temperature of $300^{\circ}C{\sim}400^{\circ}C$. The needles of lath martensite changed to parallel packet at tempering temperature of $450^{\circ}C{\sim}600^{\circ}C$. As tempering temperature increased, tensile strength, yield strength and hardness decreased, while elongation, ratio of reduction area and Charpy impact energy increased. Grain size increased when quenching temperature was $930^{\circ}C$. Grain size had prominent effect on the mechanical properties of AISI 51B20 steel. Ratio of tensile strength/yield strength and yield strength autenitized at $880^{\circ}C$ followed by tempering at $350^{\circ}C{\sim}450^{\circ}C$ showed higher values than that of autenization at $930^{\circ}C$ due to fine grain size.

• Transactions of Materials Processing
• /
• v.30 no.1
• /
• pp.22-26
• /
• 2021

The present study demonstrated the effects of processing variable and alloying elements on the processing window of austempered cast iron, one of the heat-treatable cast irons, in order to elucidate the relation between heat treatment and microstructure in terms of time and temperature. Such microstructure is strongly affected by austenitizing conditions and alloying elements. The size of processing window tends to increase initially with increasing austenitizing temperature from 1123 to 1173 K, followed by a decline in the reverse direction between 1173 and 1223 K. Thus, the optimized processing window with large frame was found at an austenitizing temperature of 1173 K. To determine the effect of Sn addition, the processing window in the sample was created by the addition of 0.08 wt.% Sn, which appeared larger than that without Sn and with 0.06 wt.% Sn.

• Journal of Industrial Technology
• /
• v.24 no.A
• /
• pp.3-8
• /
• 2004

This study was performed to investigate the effect of two step austenitized treatment on the mechanical properties and fracture characteristic of the ductile cast iron and austempered ductile cast iron(ADI). The obtained results of this study were as follows. The matrix structures of specimens were changed differently by austenitizing heat treatment. Microstructure of austempered ductile cast iron obtained by two step austenitized treatment was bainitic ferrite and retained austenite. With two step austenitized treatment, vield strength, tensile strength and hardness decreased, while the elongation increased.

• Korean Journal of Materials Research
• /
• v.25 no.12
• /
• pp.666-671
• /
• 2015

In this study, we investigated the effect of the residual carbides and tempered carbides precipitated by tempering treatment after quenching on the pitting corrosion of mod. 440A martensitic stainless steel. In quenched specimens and tempered specimens after quenching of mod. 440A martensitic stainless steel, the volume fraction of the residual carbides and total carbides decreased with the increase of the austenitizing temperature. Pitting resistance increased with the increase of austenitizing temperature. With the increase of the volume fraction of the residual and total carbides, the pitting resistance of mod. 440A martensitic stainless steel was decreased. The pitting resistance of mod. 0.5C-17Cr-0.5Ni 440A martensitic stainless steel had stronger affected by residual carbides than precipitated carbides produced by tempering.

• Journal of the Korean Society for Heat Treatment
• /
• v.9 no.3
• /
• pp.198-204
• /
• 1996

This work was carried out in order to investigate the effect of grain size on martensitic transformation temperature and morphology of Fe-27%Ni-0.27%C alloy. The martensitic transformation temperature was raised with increasing the austenitizing temperature within the range from $750^{\circ}C$ to $1200^{\circ}C$, owing to the grain growth, vacancy concentration. It was observed that the larger was the austenite grain, the higher was the martensitic transformation temperature. The influence of the austenite grain size was similar to that of the austenitizing temperature. The morphology of martensite in Fe-27%Ni-0.27%C alloy changed from lath to lenticular with the variation of grain size. From the above results, it was concluded that the martensitic transformation temperature and morphology was mainly dependent upon the austenite grain size.

• Transactions of Materials Processing
• /
• v.25 no.5
• /
• pp.306-312
• /
• 2016

Effects of manufacturing conditions, such as austenitizing temperature, patenting temperature and carbon content in steels, on mechanical properties, especially on reduction of area (RA), of hyper-eutectoid steel wires were investigated. RA increased and then decreased with transformation temperature. This was attributed to the presence of abnormal structures in steels transformed at low transformation temperatures and the occurrence of shear cracking during tensile testing of steels transformed at high transformation temperatures. The increase of austenitizing temperature resulted in the increased austenite grain size and consequently the decrease of RA. The decrease of RA with increasing the carbon content in steels was attributed to the increased fraction of cleavage fracture in tensile fractured surfaces.

• Korean Journal of Materials Research
• /
• v.25 no.11
• /
• pp.583-589
• /
• 2015

This paper presents a study on the room- and low-temperature impact toughness of hypoeutectoid steels with ferrite-pearlite structures. Six kinds of hypoeutectoid steel specimens were fabricated by varying the carbon content and austenitizing temperature to investigate the effect of microstructural factors such as pearlite volume fraction, interlamellar spacing, and cementite thickness on the impact toughness. The pearlite volume fraction usually increased with increasing carbon content and austenitizing temperature, while the pearlite interlamellar spacing and cementite thickness mostly decreased with increasing carbon content and austenitizing temperature. The 30C steel with medium pearlite volume fraction and higher manganese content, on the other hand, even though it had a higher volume fraction of pearlite than did the 20C steel, showed a better low-temperature toughness due to its having the lowest ductile-brittle transition temperature. This is because various microstructural factors in addition to the pearlite volume fraction largely affect the ductile-brittle transition temperature and low-temperature toughness of hypoeutectoid steels with ferrite-pearlite structure. In order to improve the room- and low-temperature impact toughness of hypoeutectoid steels with different ferrite-pearlite structures, therefore, more systematic studies are required to understand the effects of various microstructural factors on impact toughness, with a viewpoint of ductile-brittle transition temperature.

• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.4
• /
• pp.333-341
• /
• 1998

The study was investigated on the effect of austenitizing and austempering conditions on retained austenite amount and carbon contents in retained austenite and simultaneously the effect of these variation on hardness, tensile and impact properties. A material of as-cast condition is composed of bull's eye structure with ferrite surrounding spheroidized graphite having about $5-10{\mu}m$ size and matrix structure of pearlite. Then, the contents of spheroidized graphite was about 5%. The retained austenite and carbon contents in the retained austenite were increased with the increasing of austenitizing and austempering temperatures, while the retained austenite showed the peak value and is decreased with increasing of austempering time. With increasing of austenitizing temperature, tensile strength, elongation and impact absorb energy increased and hardness was almost not changed, while with increasing of austempering temperature, tensile strength and hardness decreased, whereas elongation and impact absorb energy was increased. With increasing of retained austenite amount, the tensile strength is slowly decreased but elongation was increased with direct proportion. Also, Impact absorb energy is shown identity value untile about 18%, but rapidly increased above it. Elongation and Impact absorb energy are strongly controlled by the amount of retained austenite, but tensile strength is affected with various factors such as retained austenite amount and bainitic morphology.