• 열처리공학회지
• /
• 제26권3호
• /
• pp.105-112
• /
• 2013

The microstructural changes of Fe-20Mn-12Cr-1Cu alloy have been studied during high temperature gas nitriding (HTGN) at the range of $1000^{\circ}C{\sim}1150^{\circ}C$ in an atmosphere of nitrogen gas. The mixed microstructure of austenite and ${\varepsilon}$-martensite of as-received alloy was changed to austenite single phase after HTGN treatment at the nitrogen-permeated surface layer, however the interior region that was not affected nitrogen permeation remained the structure of austenite and ${\varepsilon}$-martensite. With raising the HTGN treatment temperature, the concentration and permeation depth of nitrogen, which is known as the austenite stabilizing element, were increased. Accordingly, the depth of austenite single phase region was increased. The outmost surface of HTGN treated alloy at $1000^{\circ}C$ appeared Cr nitride. And this was in good agreement with the thermodynamically calculated phase diagram. The grain growth was delayed after HTGN treatment temperature ranges of $1000^{\circ}C{\sim}1100^{\circ}C$ due to the grain boundary precipitates. For the HTGN treatment temperature of $1150^{\circ}C$, the fine grain region was shown at the near surface due to the grain boundary precipitates, however, owing to the depletion of grain boundary precipitates, coarse grain was appeared at the depth far from the surface. This depletion may come from the strong affinity between nitrogen and substitutional element of Al and Ti leading the diffusion of these elements from interior to surface. Because of the nitrogen dissolution at the nitrogen-permeated surface layer by HTGN treatment, the surface hardness was increased above 150 Hv compared to the interior region that was consisted with the mixed microstructure of austenite and ${\varepsilon}$-martensite.

• 열처리공학회지
• /
• 제23권6호
• /
• pp.315-322
• /
• 2010

Effect of hardenability, grain size and microstructural change according to the change of austenitizing temperature was analyzed in Jominy hardenability test of AISI 51B20 steel. Grain growth was small, 7 ${\mu}m$ and 12 ${\mu}m$ austenite grain sizes at austenitizing temperature of $900^{\circ}C$ and $1000^{\circ}C$, respectively, while rapid grain growth was observed up to 30 ${\mu}m$ austenite grain size at austenitizing temperature of $1100^{\circ}C$. As austenitizing temperature increased from $900^{\circ}C$ to $1100^{\circ}C$, hardenability in the region within 15 mm from end-quenched surface decreased due to the grains growth of bainite and martensite mixture, on the other hand the hardenability in the region exceeding 15 mm from end-quenched surface increased. Increased hardenability was attributed to different microstructures; pearlite, fine pearlite and bainite, and bainite and martensite structures at austenitizing temperature of $900^{\circ}C$, $1000^{\circ}C$ and $1100^{\circ}C$, respectively.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.276-281
• /
• 2002

A metallurgical model for bainite transformation kinetics in the coarse-grained heat affected zone(CGHAZ) on the basis of an Avrami-type equation was studied. Isothermal transformation tests were carried out to obtain the empirical equations for incubation time and Avrami kinetic constants for C-Mn-Mo-Ni steel. The effect of prior austenite grain size(PAGS) on the reaction rate of bainite was also investigated. Compared with experimental transformation behavior of bainite, the predicted behavior was in good agreement. It was also found that a smaller grain size retard the bainite reaction rate, contrary to the classical grain size effect and this is considered to be caused by constraint of grain size to bainite growth.

• International Journal of Korean Welding Society
• /
• 제2권1호
• /
• pp.11-14
• /
• 2002

A metallurgical model for bainite transformation kinetics in the coarse-grained heat affected zone(CGHAZ) on the basis of an Avrami-type equation was studied. Isothermal transformation tests were carried out to obtain the empirical equations for incubation time and Avrami kinetic constants for C-Mn-Mo-Ni steel. The effect of prior austenite grain size(PAGS) on the reaction rate of bainite was also investigated. Compared with experimental transformation behavior of bainite, the predicted behavior was in good agreement. It was also found that a smaller grain size retard the bainite reaction rate, contrary to the classical grain size effect and this is considered to be caused by constraint of grain size to bainite growth.

• 열처리공학회지
• /
• 제3권4호
• /
• pp.23-40
• /
• 1990

This study has been carried out to investigate into some effects of Mn content with varying amounts and austenite grain size on hardenability in boron-added Fe-C-Cr-Mo alloy systems. (1) Austenite grains have been found to hardly grow in the temperature range of $900^{\circ}C$ to $950^{\circ}C$, whereas they grow rapidly in the temperature range of $975^{\circ}C$ to $1100^{\circ}C$. (2) Austenite grain growth is considerably small with increasing holding time at a given austenitizing temperature and is, in particular, hardly found to occur at a temperature of $900^{\circ}C$. (3) The hardenability improves ramarkably as Mn content is increased at three different austenitizing temperatures $900^{\circ}C$, $1000^{\circ}C$ and $1100^{\circ}C$. (4) The maximum hardenability is obtained from steels A, B and C austenitized at the $900^{\circ}C$, although Mn content is varied in each specimen.

• 한국분말재료학회지
• /
• 제28권3호
• /
• pp.246-252
• /
• 2021

The effect of sintering conditions on the austenite stability and strain-induced martensitic transformation of nanocrystalline FeCrC alloy is investigated. Nanocrystalline FeCrC alloys are successfully fabricated by spark plasma sintering with an extremely short densification time to obtain the theoretical density value and prevent grain growth. The nanocrystallite size in the sintered alloys contributes to increased austenite stability. The phase fraction of the FeCrC sintered alloy before and after deformation according to the sintering holding time is measured using X-ray diffraction and electron backscatter diffraction analysis. During compressive deformation, the volume fraction of strain-induced martensite resulting from austenite decomposition is increased. The transformation kinetics of the strain-induced martensite is evaluated using an empirical equation considering the austenite stability factor. The hardness of the S0W and S10W samples increase to 62.4-67.5 and 58.9-63.4 HRC before and after deformation. The hardness results confirmed that the mechanical properties are improved owing to the effects of grain refinement and strain-induced martensitic transformation in the nanocrystalline FeCrC alloy.

• Journal of Welding and Joining
• /
• 제34권6호
• /
• pp.55-61
• /
• 2016

Recently developed ferritic heat resistance steel, T24 was used to evaluate microstructure characteristics of simulated heat affected zone. Also, correlation between the prior austenite grain size and amount of $M_{23}C_6$ carbide dissolution was discussed. With the increasing of peak temperature, Grain size steadily increased up to $1050^{\circ}C$ and then rapidly increased at $1150^{\circ}C$. Of the peak temperature $950{\sim}1050^{\circ}C$, amounts of $M_{23}C_6$carbide dissolution are low. But Most of $M_{23}C_6$ carbide that is inhibited grain growth were dissolved above $1050^{\circ}C$ and decreased volume fraction of carbide. This indicates that grain growth may be achieved through dissolution of carbide in the base material. As of welding, due to very rapid heating rate, $M_{23}C_6$ carbide exists above equilibrium solution temperature that is $800^{\circ}C$, even at $1050^{\circ}C$. So, It was confirmed that close correlation between carbide dissolution in the base material and grain growth. Calculated grain size has a linear relationship with peak temperature, on the other hand, measured grain size discontinuously increased between $950{\sim}1050^{\circ}C$ and above $1050^{\circ}C$. Grain size of heat affected zone at $1350^{\circ}C$ peak temperature showed maximum 67um and minimum 4um. Also, The number of side showed 3 to 10.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.138-143
• /
• 2001

To perform the rigorous integrity evaluation of RPV, it is necessary to consider metallurgical factors such as microstructure evolution during multi-pass welding process and PWHT. The microstructures of the heat affected zone(HAZ) of SA508 steel were predicted by a combination of simulated thermal analysis and a simple kinetic models for austenite grain growth and austenite-ferrite transformation. Phase equilibrium of SA508 steel were calculated using a Thermo-Calc package. Carbide growth in th HAZ were predicted by a empirical model, taking into account the predicted microstructure evolution.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.73-78
• /
• 2000

On this study, the fatigue crack propagation of super duplex stainless steel is investigated in conditions of various volume fraction of austenite phase by changing heat treatment temperature. And we analysed acoustic emission signals during the fatigue test by time-frequency analysis methods. As the temperature of heat treatment increased, volume fraction of austenite decreased and coarse grain was obtained. The specimen heat treated at $1200^{\circ}C$ had longer fatigue life and slower rate of crack growth. As a result of time-frequency analyze of acoustic emission signals during fatigue test, main frequency was $200{\sim}300kHz$ having no correlation with heat treatment and crack length, and 500kHz was obtained by dimple and separate of inclusion

• 열처리공학회지
• /
• 제3권4호
• /
• pp.10-22
• /
• 1990

A study has been investigated on the effect of mechanical properties (tension strength, rotary bending fatigue strength, wear resistance, hardness) according to the carbide particle size variation by the treatment of 1) quenching tempering, and 2) quenching, subzero treatment and tempering. The material used in this investigation was a typical bearing steel, high C high Cr, AISI E 52100. The result obtained in this study were as follows : (1) Finer the carbide particle size increasing the hardness and retained austenite in same quenching condition. (2) Finer the carbide particle size reduced the tension and rotary bending fatigue which were resulted from austenite grain growth and carbide precipitation on grain boundry that induced by carbide refine heat treatment. (3) Finer the carbide particel size increasing the wear resistance which were resulted by uniform distribution of carbide and increased hardness induced by microstructural uniform hardenability of matrix. (4) When the carbide particles were refinded, subzero treatment is effective only wear resistance and hardness.