• Journal of Korea Foundry Society
• /
• v.12 no.5
• /
• pp.390-396
• /
• 1992

In this study, we investigated effect of austempering factors and Mn addition on mechanical properties of ADI with ferrite-bainite matrix by pearlite-bainite transformation treatment. Ductile cast iron specimens containing various of Mn were austenitized at 875$^{\circ}C$ for 350 sec or 925$^{\circ}C$ for 160 sec and then austempered at 300$^{\circ}C$ or 400$^{\circ}C$ for the various periods(5 to 30 min). Manganese increased pearlite volume fraction in as cast ductile cast iron. The obtained results are as follows ; 1) In austenitizing, hardness of sepecimens austenitized at 875$^{\circ}C$ for 350 sec was higher than that of 925$^{\circ}C$ for 160 sec. 2) In effect of austempering temperature, tensile strength and handness of specimens austempered at 300$^{\circ}C$ was higher than that of 400$^{\circ}C$. However, elongation had reverse tendency. 3) Increasing austempering time decreased hardness due to the increment of bainite and retained austenite fractions. However, toughness are increased.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.12
• /
• pp.1-7
• /
• 2020

An experimental evaluation of bending fatigue strength for austempered ductile iron (ADI) spur gears was performed using a Zwick fatigue tester. The gear material was manufactured using vertical continuous casting, resulting in the radius of the graphite grains being smaller. The stress-number of cycles curve (S-N curve) for the bending fatigue strength of the ADI spur gears thus manufactured, without any specific surface treatments, was obtained using post-processing software. It was observed that when the reliability was 50%, the allowable root stress was 610 MPa. was calculated using an analytical method as well as the finite element method, and the difference between the values calculated using the two methods is only 7%. This study provides a reliable basis to rate the reliability design of small gearboxes in automation in the future.

• Journal of Korea Foundry Society
• /
• v.15 no.2
• /
• pp.146-155
• /
• 1995

This study was performed to investigate the effect of austempering temperature on the mechanical properties and fracture characteristics of the ductile cast iron with Cu, Mo and Cu, Mo, Ni. The results obtained from this study are summarized as follows; Microstructures of Cu-Mo and Cu-Mo-Ni ductile cast iron by austempering were obtained low bainite with some martensite at $250^{\circ}C$, mixture structure of upper and low bainite obtained at $300^{\circ}C$ and upper bainite obtained at $350^{\circ}C$. Tensile, impact and fracture toughness properties were remarkably controlled by retained austenite. With increasing austempering temperature, tensile and yield strength, hardness decreased, while the elongation and impact absorption energy, fracture toughness increased. With adding Ni, tensile and yield strength increased and elongation, facture toughness and impact absorption energy decreased. Retained austenite increased with increasing austempering temperature and the fracture surface were shown mixture structure of fibrous and dimple.

• Journal of Ocean Engineering and Technology
• /
• v.2 no.2
• /
• pp.87-95
• /
• 1988

This paper is studied to know corrowive wear characteristics of austempered ductile cast ironin corrosive environments against mating SM45C hardened two test pieces in distilled water and NaCl aqueous solution. The corrosive wear mechanism was investigated by scanning electron microscopy and retained austenite volume fraction was investigated by X-ray diffractometer. The experimental result show that the corrosive wear characteristics depend largely on the $\textrm{Fe(OH)}_{3}$which is influenced by the critical sliding distance $L_{cr}$ and $L_{cr}$ shorted with increasing NaCl concentration. It was found that the carbides in matrix have a significant effect on their corrosive wear resisance and the fine acicular bainite showed corrosive wear resistance stronger than that of the coarse acicular and platelet bainite. From above results the model of corrosive wear mechanism in corrosive environments is proposed.

• Journal of Korea Foundry Society
• /
• v.11 no.5
• /
• pp.392-397
• /
• 1991

This study has been performed to investigate the austempering heat treatment response and mechanical properties of a high carbon(0.9%), silicon(1.5-4.5%)-alloyed cast steel, with a chemical composition similar to that of the matrix of a ductile cast iron. Tensile and hardness tests were used to evaluate the effects of a wide variety of austempering heat treatment variables. SEM metallography and X-ray measurements of stabilized austenite were also performed for all the specimens employed. The austempered microstructures which contain up to 39% stabilized austenite were obtained. Mechanical properties and microstructures depended primarily on the austempering time and temperature. The optimum mechanical properties were obtained at the chemical compositions of 0.9% C and 2.5% Si.

• Journal of Korea Foundry Society
• /
• v.16 no.2
• /
• pp.109-115
• /
• 1996

Effect of various austempered structures on fracture characteristics of C/V graphite cast iron has studied. The tensile strength and hardness reached the maximum value of 971.4MPa and HB302 at the austempering temperature of $250^{\circ}C$, respectively. As the austempering temperature increased, the amount of retained austenite increased from 18% to 22, 29%, while $K_{IC}$ values ranged from the value of $65MPa{\cdot}m^{12} to 70MPa{\cdot}m^{1/2}, 66MPa{\cdot}m^{1/2}. This fact that $K_{IC}$ value was not sensitive to the increase of the amount of the retained austenite was that $K_{IC}$ was dependent on the matrix structure in lower bainitic matrix, while dependent on the notch effect from C/V graphite shape in upper bainitic matrix. Fractured surfaces showed a ductile fracture pattern at $300^{\circ}C$. Very large coalescence by C/V graphite and relatively small voids by spheroidal graphite were observed.

• Journal of Korea Foundry Society
• /
• v.35 no.1
• /
• pp.1-7
• /
• 2015

In this study, we investigated the effect of carbon on mechanical properties with different austempering conditions of high carbon(0.7~1.3wt.%C)-2.0wt.%Si steels. The specimens were austenitized at 850, 925 and $1020^{\circ}C$, and austempered at 260, 320 and $380^{\circ}C$ for the various period of time from 3 min to 300 min. After heat treatment, the evolution of stage I and stage II was identified with optical microscope, XRD and hardness test. When the austempering temperature was $260^{\circ}C$, the microstructure consisted of the lower ausferrite while the upper ausferrite micro-structure was formed at $380^{\circ}C$. As the austempering temperature increases from 260 to $380^{\circ}C$, the tensile strength decreases and elongation increases. In addition, when carbon content increases, tensile strength and elongation decrease.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1404-1411
• /
• 1993

This study was undertaken to investigate the corrosive wear charateristics upon various transformation condition of austempered low-alloy ductile cast iron in corrosive environments against mating specimen made of the hardened SM45C. The corrosive wear test was carried out by rubbing the annular surface of two test pieces in distilled water and aqueous solution at constant sliding speed of 0.5m/s. In severe wear region, the corrosive wear rate Wc increased hastily with NaCl concentration owing to intermetallic adhesion but Wc went down slowly in mild wear region due to lubricating effect of the corrosion product. The critical sliding distance decreased with increasing NaCl concentration due to increased generation rate of the corrosion product and the specific corrosive wear rate has maximum in 1% NaCl aqueous solution at mild wear region. With the variation of matrix, the corrosive wear resistance of the fine acicular bainite was higher than that of coarse upper bainite because of reducing the local cell reaction by carbides. A growth in volume fraction of retained austenite in matrix increased the Wc due to soften surface, but has a declining tendency of Wc in mild wear region.

• Journal of Korea Foundry Society
• /
• v.11 no.4
• /
• pp.331-337
• /
• 1991

Various test specimens were prepared by austempering low alloyed Mo-Ni-Cu ductile iron blocks of high graphite nodule count at 270, 320 or $370^{\circ}C$ for 0.5, 1, 3 or 9hrs. Tensile test, CVN impact test and plane-strain fracture toughness test(compact tension specimen of 50mm W) were done for each heat treatment condition at room temperature. X-ray diffractometer and optical microscope were used to investigate the change of microstructure and relationships between microstructure and test results. The highest retained austenite volume percent at each austempering temperature was corresponded to the highest mechanical property. The highest elongation value of 17%, U.T.S. value of 1,600 MPa or $K_{IC}$ value of 90MPa${\surd}$m were reached at each optimum condition. The best heat treatment condition for fracture toughness were 3hrs' holding time combined with the austempering temperature of 270 and $320^{\circ}C$, and 1hr's of $370^{\circ}C$.

• Journal of Korea Foundry Society
• /
• v.34 no.1
• /
• pp.1-5
• /
• 2014

The austempering transformation behavior in Fe-0.7wt.%C-2.3wt.%Si-0.3wt.%Mn steel is investigated. Each specimen was austenitized for 60 min at $900^{\circ}C$, and austempered at $380^{\circ}C$ for different time periods varying from 2 min to 256 min. After the austempering heat treatment, the Stage I and II evolutions are performed using optical metallography, X-ray diffraction and image analyses. Variations in the X-ray diffraction patterns and lattice parameters of the ferrite and austenite demonstrate that the residual austenite decomposes into ferrite and carbide during the Stage II evolution; moreover the amount of ferrite increases during the Stage I evolution. While the amount of austenite increases during Stage I, it dicreases during Stage II. Overall, the variations in the volume fractions of the microstructure and carbide formation in stages I and II meet high temperature austempering reaction of the ausferrite microstructure.