• Journal of the Korean Geotechnical Society
• /
• v.19 no.2
• /
• pp.247-254
• /
• 2003

While the interests in the environmental problem during the construction are increasing, the use of low noise-vibration auger-drilled pilling is increasing to solve noise and vibration problem in pilling. Therefore, in Korea, SIP (Soil-Cement Injected Precast Pile) method is mainly used as auger-drilled pilling. However, there is no proper design criteria compatible with the ground condition of Korea, so which is most wanted. To improve and supplement this situation, direct shear tests for the friction between SIP pile skin interface and soil were executed on various conditions. Through the analysis of test results, skin friction characteristics of SIP were investigated thoroughly Also, hyperbolic model parameter fomulas which describe the friction behavior and the new non-linear unit skin friction capacity model with SM, SC soil were suggested.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.4
• /
• pp.308-317
• /
• 2007

We fabricated thermally-evaporated 10 nm-Ni/(poly)Si and 10 nm-$Ni_{0.5}Co_{0.5}$/(Poly)Si structures to investigate the microstructure of nickel silicides at the elevated temperatures required lot annealing. Silicides underwent rapid annealing at the temperatures of $600{\sim}1100^{\circ}C$ for 40 seconds. Silicides suitable for the salicide process formed on top of both the single crystal silicon actives and the polycrystalline silicon gates. A four-point tester was used to investigate the sheet resistances. A transmission electron microscope and an Auger depth profilescope were employed for the determination of vortical microstructure and thickness. Nickel silicides with cobalt on single crystal silicon actives and polycrystalline silicon gates showed low resistance up to $1100^{\circ}C$ and $900^{\circ}C$, respectively, while the conventional nickle monosilicide showed low resistance below $700^{\circ}C$. Through TEM analysis, we confirmed that a uniform, $10{\sim}15 nm$-thick silicide layer formed on the single-crystal silicon substrate for the Co-alloyed case while a non-uniform, agglomerated layer was observed for the conventional nickel silicide. On the polycrystalline silicon substrate, we confirmed that the conventional nickel silicide showed a unique silicon-silicide mixing at the high silicidation temperature of $1000^{\circ}C$. Auger depth profile analysis also supports the presence of this mixed microstructure. Our result implies that our newly proposed NiCo-alloy composite silicide process may widen the thermal process window for the salicide process and be suitable for nano-thick silicides.

• Journal of the Korean Vacuum Society
• /
• v.7 no.2
• /
• pp.82-87
• /
• 1998

In the oxidation process of the $NH_3/O_2$ oxidation method, adding $NH_3$ gas to $O_2$ gas, the detected outlet gases in the reaction quartz chamber are N2, $O_2$ and $H_2O$ and in addition, a very small quantity of $CO_2$, NO and $NO_2$ are detected. Two kinds of species ($O_2$ and H2O) contribute to oxidation, so the growth rate is determined by oxidation temperature and by also partial pressure of the NH3 and $O_2$ gases. The slop of growth rate is identified to be medial and in parallel between that of the dry and wet oxidation. Auger electron spectroscopy (AES) indicates that $NH_3/O_2$ oxide film has a certain stoichiomerty of $SiO_2$, this oxidation method restrains the generation of defects in the $SiO_2/Si$ interface, minimizing fixed charges. The breakdown voltage of $NH_3/O_2$ oxide film (470$\AA$) is 57.5 volts, and the profile of the C-V curve including flat band voltage (0.29 volts) agree with the ideal curve.

• Journal of the Korean Vacuum Society
• /
• v.14 no.4
• /
• pp.229-237
• /
• 2005

The degradation phenomena in SiGe hetero-junction bipolar transistors(SiGe HBTs) induced by bias stress are investigated in this review. If SiGe HBTs are stressed over a specific time interval, the device parameters deviate from their nominal values due to the internal changes in the devices. Reverse-bias stress on emitter-base(EB) junctions causes base current increase and current gain decrease because carriers accelerated by the electrical field generate recombination centers. When forward-bias current stress is conducted at an ambient temperature above $140^{\circ}C$ , hot carriers produced by Auger recombination or avalanche multiplication induce current gain fluctuation. Mixed-mode stressing, where high emitter current and high collector-base voltage are simultaneously applied to the device, provokes base current rise as EB reverse-bias stressing does.

• KSTLE International Journal
• /
• v.6 no.2
• /
• pp.39-44
• /
• 2005

Friction and wear properties of the Boron carbide ($B_{4}C$) coating 100 nm thickness were studied under various relative humidity (RH). The boron carbide film was deposited on silicon substrate by DC magnetron sputtering method using $B_{4}C$ target with a mixture of Ar and methane ($CH_4$) as precursor gas. Friction tests were performed using a reciprocation type friction tester at ambient environment. Steel balls of 3 mm in diameter were used as counter-specimen. The results indicated that relative humidity strongly affected the tribological properties of boron carbide coating. Friction coefficient decreased from 0.42 to 0.09 as the relative humidity increased from $5\%$ to $85\%$. Confocal microscopy was used to observe worn surfaces of the coating and wear scars on steel balls after the tests. It showed that both the coating surface and the ball were significantly worn-out even though boron carbide is much harder than the steel. Moreover, at low humidity ($5\%$) the boron carbide showed poor wear resistance which resulted in the complete removal of coating layer, whereas at the medium and high humidity conditions, it was not. X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) analyses were performed to characterize the chemical composition of the worn surfaces. We suggest that tribochemical reactions occurred during sliding in moisture air to form boric acid on the worn surface of the coating. The boric acid and the tribochemcal layer that formed on steel ball resulted in low friction and wear of boron carbide coating.

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.667-673
• /
• 1998

Rebar corrosion in a simulated pore solution (SPS) with chloride ion was analyzed by Tafel and AC impedance method and corrosion effects of surface roughness and iron oxide layer were also investigated. Corrosion estimation of rebar by electrochemical impedance spectroscopy is very useful, and the measured value can be adapted to proposed electrochemical equivalent circuit model. Corrosion potential increased to the cathodic direction as the concentration of chloride ions increased and corrosion current had the same tendency as above. Surface films were analyzed with scanning electron microscope and Auger electron spectroscopy. Thermally oxidized layer by torch flame for 15 sec was very poor at anti-corrosive property. The corrosion rate of rebar increased as the surface roughness increased. Also, higher temperatures above RT of SPS in initial stage caused a rebar to be corroded faster.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.5
• /
• pp.37-54
• /
• 2008

The standard construction manual of the SDA (Separated Doughnut Auger) piling method was proposed so that the resisting capacity of the augered piles could work effectively. 438 dynamic pile load tests were performed on 379 test piles, which were installed at 36 sites in Korea by the SDA piling method with application of various water-cement ratio of cement milks. The dynamic pile load test results showed that the bearing capacity of the SDA augered piles depended on the water-cement ratio of cement milks. And couple of the formulas were presented according to water-cement ratio and various grounds to estimate quantitatively both the unit end bearing and the unit frictional capacity of the SDA augered piles. It was also considered that the water-cement ratio of cement milks exerts an influence on the bearing capacity of the SDA augered piles. The presented formulas were compared with the existing formulas, which were presented by several standard design codes to design the augered piles.

• Journal of IKEEE
• /
• v.26 no.1
• /
• pp.50-55
• /
• 2022

SiC is a power semiconductor with a wide bandgap, high insulation failure strength, and thermal conductivity, but many deep-level defects. Defects that appear in SiC can be divided into two categories, defects that appear in physical properties and interface traps that appear at interfaces. In this paper, Z_1/2 trap concentration 0 ~ 9×10¹⁴ cm^-3 reported at room temperature (300 K) is applied to SiC substrates and epi layer to investigate turn-on characteristics. As the trap concentration increased, the current density, Shockley-read-Hall (SRH), and Auger recombination decreased, and Ron increased by about 550% from 0.004 to 0.022 mohm.

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.1
• /
• pp.57-61
• /
• 2006

The research on surface modification technology has been advanced to improve the properties of engineering materials. Ion implantation is a novel surface modification technology that enhances the mechanical, chemical and electrical properties of substrate's surface using accelerated ions. In this research, nitrogen ions were implanted into AC7A aluminum substrates which would be used as molds for rubber molding. The composition of nitrogenion implanted aluminum and distribution of nitrogen ions were analyzed by Auger Electron Spectroscopy (AES). To analyze the modified surface, properties such as hardness, friction coefficient, wear resistance, contact angle, and surface roughness were measured. Hardness of ion implanted specimen was higher than that of untreated specimen. Friction coefficient was reduced, and wear resistance was improved. From the experimental results, it can be expected that implantation of nitrogen ions enhances the mechanical properties of aluminum mold.

• Corrosion Science and Technology
• /
• v.4 no.2
• /
• pp.64-68
• /
• 2005

Various metallic materials are coated on Fe base materials via thermal spraying or welding process to improve both corrosion resistance as well as erosion resistance of the Fe base materials used in buildings and special works. The mechanical properties and corrosion resistance of the coat are estimated by means of hardness measurement and anodic polarization test. In additions, the effect of alloying elements and microstructure of the coatings on the mechanical and chemical properties of the coat is investigated using X- ray diffraction, Optical microscope, Transmission electron microscopy and Auger analysis. The coating deposited by tungsten inert gas (TIG) welding exhibit a good combination of hardness and corrosion properties.