• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.120-125
• /
• 1993

The surface roughness of workpiece is reduced during spark-out. The reduction of roughness is a benefit of spark-out, but spark-out lowers productivity. The characteristics of spark-out are different to those of plunge grinding to which feed is applied. This difference is due to overlapping cutting during spark-out. Effect of spark-out is in proportion to volume of grain wear. This phenomenon is due to different overlapping area. Dressing interval can be enlarged by spark-out, when volume of grain wear is large. In this study, the characteristic of spark-out was studied by spark-out obserbation in various grinding conditions. For this purpose thrust force, spark-out time and surface roughness of workpiece were experimentally investigated in various grinding conditions.

• Journal of the Korean Ceramic Society
• /
• v.37 no.3
• /
• pp.211-218
• /
• 2000

The attrition-milled powder mixtures of Al and Al2O3 were oxidized below 140$0^{\circ}C$ for 1 hr and post-sintered at 150$0^{\circ}C$ and 1$600^{\circ}C$ for 2 hr. During attrition milling, ZrO2 was added to the system by grinding effect of ZrO2 balls. The average particle size of the powder mixtures was decreased by the attrition milling as the aluminum content decrease. Above 120$0^{\circ}C$, sintering behaviro was observed on the fine Al2O3 particles resulted from the oxidation of Al. The specimens heat-treated at 140$0^{\circ}C$ for 1 hr showed the bending strength of 166 MPa and hardness of 220 MPa. The specimens post-sintered at 1$600^{\circ}C$ for 2hr had a linear shrinkage of 9~12% and a relative density of about 95%. After the post-sintering, the specimens having 55 vol% Al content revealed the bending strength of 513 MPa and hardness of 718 MPa. The Weibull modulus to the bending strength was about 16.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.7
• /
• pp.343-352
• /
• 2016

Effects of grinding time and chemicals dosage in arsenic removal from contaminated paddy soil in China were investigated using lab scale attrition and froth flotation combining process. Arsenic concentration in the field soil was 76.51 mg/kg, exceeding Korean and Chinese standards, and predominant arsenic compounds fraction in sequential extraction was "residual" (over 80%). After wet sieving, soil with >2 mm and < 0.038 mm showed concentration lower than 'Warning Level' in Korea. Soil with 0.038-0.075 mm, showing the highest concentration, was discarded since it occupied minor weight fraction (10.1%). Thus soil between 0.075 and 2 mm was only used in the combining process. The highest Arsenic concentration in progeny fragments smaller than 0.038 mm reached up to 981.66 mg/kg after 5 min of attrition. Optimal dosage of collector ($C_5H_{11}OCS_2K$) and modifier ($Na_2S$ and $CuSO_4$) in froth flotation process for the selective separation of the chipped progeny particles from the parent fragments were determined both as 200 g/ton. Arsenic removal efficiency in froth flotation process was 38.47% and it was increased to 72.74% in additional flotation process, scavenging. Average arsenic concentration after overall process - wet sieving, attrition and froth flotation - was estimated to 16.45 mg/kg.

• Journal of the Mineralogical Society of Korea
• /
• v.30 no.4
• /
• pp.137-147
• /
• 2017

Sericite is a clay mineral that has a wide applications in the industry, depending on its purity. To maintain sericite's purity as high as possible it is necessary to remove its gangue minerals or control their contents prior to use for high value-added products and applications. In this study, the wet beneficiation of sericite by applying selective grinding and sedimentation techniques, were investigated. The ore mineral was composed mainly of sericite, quartz and calcite. Analysis showed that the content of sericite increased along with the particle size decrease, but the contents of impurity minerals as quartz and calcite were tended to decrease relatively with particle size decrease. The results of liberation tests using an attrition scrubber showed that the increase in residence time and slurry density have increased the generation of fine particles in -325 mesh size range. It was observed, however, that the contents of impurities such as quartz and calcite in such fine particles also increased during prolonged scrubbing. In the dispersed form without breaking, the yield of the recovered concentrate was 15.4 wt% and the $K_2O$ content was 9.84 wt%, after the dispersed slurry was allowed to settle for 20 minutes. On the other hand, the concentrate yield was increased to 23.4 wt% after 10 minute attrition scrubbing and 40 minute sedimentation, while its $K_2O$ content was decreased to 9.71 wt%. Most of final products were observed as platelet-shaped particles containing Si, Al and K which are main component of sericite.

• Resources Recycling
• /
• v.15 no.2 s.70
• /
• pp.37-44
• /
• 2006

The total amount of graphite reserves in Korea is about 260 thousand tons. Graphite larks international competitiveness it is mined in only few mines, but recently the demand of portable electronic has increased. Therefore a research for manufacturing domestic high purity graphite is necessary because all of high purity graphite used electrode of 2nd batter depends on expensive importation. A preprocessing level for producing high purity graphite, flotation was conducted using microbubble column machine. In this research $D_{50}=10.314{\mu}m$ sample was used which was produced after grinding 29.50% F.C. primary crushing sample($D_{50}=69.393{\mu}m$) for 20 minutes through attrition mill. As a result using this sample, product above 95% F.C. with recovery over 90% was obtained with only after first stage process through the microbubble column.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.30 no.1
• /
• pp.110-115
• /
• 2003

Dens evaginatus is an anomalous tooth development arising during morphodifferentiation. It is most often reported in premolar, and familial occurrence has been reported. The primary dental complication of dens evaginatus is fracture or wear of the tubercle which leads to pulp exposure, pulpal necrosis and periapical infection. Pathosis of the pulp can occur before complete root formation with cessation of root development. A rational and conservative approach to the management of dens evaginatus in vital teeth includes early diagnosis and treatment to prevent fracture or attrition of the tubercle. This treatment would include careful sequential grinding, pulp capping, preventive resin restoration. When presented with a case of dens evaginatus in a nonvital tooth with incomplete root development, the treatment of choice has been extraction, apexification. We report two cases of dens evaginatus that appear in two sisters. In the elder, a periapical lesion on radiographs is shown, and it is treated by calcium hydroxide apexification. The other sister is early recognized of dens evaginatus, it is treated using glass ionomer cement reinforcing with sequential grinding.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.28 no.1
• /
• pp.87-101
• /
• 2012

Bruxism is extensively defined as a diurnal or nocturnal parafunctional habit of tooth clenching or grinding. The etiology of bruxism may be categorized as central factors or peripheral factors and according to previous research results, central factors are assumed to be the main cause. Bruxism may cause tooth attrition, cervical abfraction, masseter hypertrophy, masseter or temporalis muscle pain, temporomandibular joint arthralgia, trismus, tooth or restoration fracture, pulpitis, trauma from occlusion and clenching in particularly may cause linea alba, buccal mucosa or tongue ridging. An oral appliance, electromyogram or polysomnogram is used as a tool for diagnosis and the American Sleep Disorders Association has proposed a clinical criteria. However the exact etiology of bruxism is yet controversial and the selection of treatment should be done with caution. When the rate of bruxism is moderate or greater and is accompanied with clinical symptoms and signs, treatment such as control of dangerous factors, use of an oral appliance, botulinum toxin injection, pharmacologic therapy and biofeedback therapy may be considered. So far, oral appliance treatment is known to be the most rational choice for bruxism treatment. For patients in need of esthetic correction of hypertrophic masseters, as well as bruxism treatment, botulinum toxin injection may be a choice.