• Journal of the Korea Concrete Institute
• /
• v.25 no.3
• /
• pp.339-345
• /
• 2013

This study is to derive from the required performances and the optimum mix proportion of the roof concrete placed in the in-ground LNG storage tank with a capacity of 200000 $m^3$, and propose the actual data for site concrete work. The concrete placing work without sliding and segregation in the fresh concrete condition is very important because the slope of domed roof is varied in the large range by its curvature. Also the control of hydration heat and the strength development at test ages are classified with massive section about 1.4 m thick and considered to the pre-stressing work and removal of air support after concrete placing work. Considering above condition, slump range is selected $100{\pm}25$ mm under the slope $20^{\circ}$ and $150{\pm}25$ mm over the slope $20^{\circ}$ s until 60 minutes of elapsed time. Also, the roof concrete is satisfied with compressive strength range including design strength at 91 days (30 MPa), pre-stressing work at 7 days (10 MPa), air support removal work at 21 days (14 MPa). Replacement ratio of limestone powder is determined by confined water ratio test and main design factors include water-cement ratio (W/C), sand-aggregate ratio and dosage of admixture. As test results, the optimum mix proportion of the roof concrete used low heat cement is as followings. 1) Replacement ratio of limestone powder 25% by confined water ratio test 2) Water-cement ratio 57.8% 3) Sand-aggregate ratio 42.0%. Also, test results for the adiabatic temperature rising test is satisfied with its criteria and shown the lower value compared to preceding storage tank (TK-13, 14). These required performances and the optimum mix proportion is to apply the actual construction work.

• Journal of Intelligence and Information Systems
• /
• v.17 no.2
• /
• pp.61-75
• /
• 2011

A Geographic Information System(GIS) is a system that captures, stores, analyzes, manages and presents data with reference to geographic location data. In the later 1990s and earlier 2000s it was limitedly used in government sectors such as public utility management, urban planning, landscape architecture, and environmental contamination control. However, a growing number of open-source packages running on a range of operating systems enabled many private enterprises to explore the concept of viewing GIS-based sales and customer data over their own computer monitors. K telecommunication company has dominated the Korean telecommunication market by providing diverse services, such as high-speed internet, PSTN(Public Switched Telephone Network), VOLP (Voice Over Internet Protocol), and IPTV(Internet Protocol Television). Even though the telecommunication market in Korea is huge, the competition between major services providers is growing more fierce than ever before. Service providers struggled to acquire as many new customers as possible, attempted to cross sell more products to their regular customers, and made more efforts on retaining the best customers by offering unprecedented benefits. Most service providers including K telecommunication company tried to adopt the concept of customer relationship management(CRM), and analyze customer's demographic and transactional data statistically in order to understand their customer's behavior. However, managing customer information has still remained at the basic level, and the quality and the quantity of customer data were not enough not only to understand the customers but also to design a strategy for marketing and sales. For example, the currently used 3,074 legal regional divisions, which are originally defined by the government, were too broad to calculate sub-regional customer's service subscription and cancellation ratio. Additional external data such as house size, house price, and household demographics are also needed to measure sales potential. Furthermore, making tables and reports were time consuming and they were insufficient to make a clear judgment about the market situation. In 2009, this company needed a dramatic shift in the way marketing and sales activities, and finally developed a dedicated GIS_based market analysis and sales management system. This system made huge improvement in the efficiency with which the company was able to manage and organize all customer and sales related information, and access to those information easily and visually. After the GIS information system was developed, and applied to marketing and sales activities at the corporate level, the company was reported to increase sales and market share substantially. This was due to the fact that by analyzing past market and sales initiatives, creating sales potential, and targeting key markets, the system could make suggestions and enable the company to focus its resources on the demographics most likely to respond to the promotion. This paper reviews subjective and unclear marketing and sales activities that K telecommunication company operated, and introduces the whole process of developing the GIS information system. The process consists of the following 5 modules : (1) Customer profile cleansing and standardization, (2) Internal/External DB enrichment, (3) Segmentation of 3,074 legal regions into 46,590 sub_regions called blocks, (4) GIS data mart design, and (5) GIS system construction. The objective of this case study is to emphasize the need of GIS system and how it works in the private enterprises by reviewing the development process of the K company's market analysis and sales management system. We hope that this paper suggest valuable guideline to companies that consider introducing or constructing a GIS information system.

• Journal of Korean Society of Forest Science
• /
• v.81 no.1
• /
• pp.53-65
• /
• 1992

For elucidating effective methods of restoration of forest recreational sites where management goals are maintaining naturalness and conserving natural ecosystem, seeding, fertilization and soil surface treatment were used for four years at the devastated forest-floor. For restoration of forest-floor vegetation, factorial experiment was used with a split plot design(main plot : fertilization, subplot : soil surface${\times}$seeding) and a randomized complete block design (fertilization${\times}$seeding) at the Kwanaksan Aboretum, Anyang, Kyonggido. Results were summarized as follows : Soil surface softening with tipping and ripping and straw-mat mulching (70% coverage) treatment was effective on germination, survival and growth of seeded vegetation at devastated forest-floor. Especially, straw-mat mulching treatment was effective on soil surface stabilization and seedling's survival at eroded soil surface, while complete soil surface softening treatment was effective on germination, survival and early growth of tree species of late-successional series. Introducing seeds of native species of pioneer or early-successional series, with good growth capability in barren soil was effective on rapid restoration in devastated forest-floor with its soil surface previously compacted and its surviving seeds washed away. When the seeding and straw-mat mulching after partial soil surface softening with tipping and ripping treatment were employed, it took about three years to restore the devastated forest-floor where surface erosion had been undertaken for an extended period of time and where naturally surviving seeds of native species had been washed away. Softening treatment of soil surface was effective for about two years, and seeding and soil surface treatment increased number of seedlings and improved soil surface environment through fixing of movement of the fallen leaves. Fertilizing effect was not oberserved, mainly due to seeding exposure and poor physical condition including soil surface erosion, low soil water potential and drought, etc, at the field experimental site. However, application of nitrogen and phosphate fertilizers was effective on seedling survival of the species in late-successional series, while lime application adversely affected the seedling survival.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.4
• /
• pp.261-271
• /
• 2016

In the prediction of response of a pile in soil, numerical approaches such as a finite element method are generally applied due to complicate nonlinear behaviors of soils. However, the numerical methods based on the finite elements require heavy efforts in pile and soil modelling and also take long computing time. So their usage is limited especially in the early design stage in which principal dimensions and properties are not specified and tend to vary. On the contrary, theoretical approaches adopting linear approximations for soils are relatively simple and easy to model and take short computing time. Therefore, if they are validated to be reliable, they would be applicable in predicting responses of a pile in soil, particularly in early design stage. In case of wind turbines regarded in this study, it is required to assess their natural frequencies in early stages, and in this simulation the supporting pile inserted in soil could be replaced with a simplified elastic boundary condition at the bottom end of the wind turbine tower. To do this, analysis for a pile in soil is performed in this study to extract the spring constants at the top end of the pile. The pile in soil can be modelled as a beam on elastic spring by assuming that the soils deform within an elastic range. In this study, it is attempted to predict pile deformations and influence factors for lateral loads by means of the beam-on-spring model. As two example supporting structures for wind turbines, mono pile and suction pile models with different diameters are examined by evaluating their influence factors and validated by comparing them with those reported in literature. In addition, the deflection profiles along the depth and spring constants at the top end of the piles are compared to assess their supporting features.

• Korean Journal of Ecology and Environment
• /
• v.46 no.1
• /
• pp.33-40
• /
• 2013

From March 2012 to January 2013, this study was conducted as a part of the project for making a precise electronic ecological zoning map of vegetation on a highly reduced scale of 1 to 5,000 with a view to improving management efficiency of national parks and enlarging the availability of the data produced from the basic research monitoring the resources of national parks. For the research accuracy and rapidity, a vegetation map was specially created for the on-the-site-vegetation research. To make the map more meticulous, we categorized the vegetation database into five groups: broadleaved forest, coniferous forest, mixed forest, rock vegetation and miscellaneous one. After comparing the results of the data built for the vegetation research and the actual research findings, it was made clear that vegetation of both categories was almost the same in case of broad-leaved forest with 72.20% and 78.45% respectively, and also equivalent in other groups like, for example, coniferous forest (16.70%, 13.41%), mixed forest (9.50%, 7.49%) and rock vegetation (0.60%, 0.15%). According to the precise vegetation map produced from the research, the deciduous broad-leaved forest was the most widely prevalent type in the correlated hierarchical classification of vegetation, occupying 65.78% of the overall vegetation. It was followed by mountain valley forest (15.17%), coniferous forest (10.90%), and plantation forest (7.00%) in order. It is particularly noteworthy that Mt. Deogyusan national park has retained a very stable and versatile forest vegetation in the outstanding state since approximately 20% of the mountain turns out to belong to the I grade vegetation conservation classification which contains climax forests, unique vegetation, subalpine vegetation, matured stands which are older than 50 years and etc.

• Korean Journal of Environment and Ecology
• /
• v.26 no.4
• /
• pp.604-619
• /
• 2012

According to the concept of woodland aesthetic in Germany and forest design in United Kingdom, artificial forest should be restore ecologically step by step in National Park, Korea. This study was carried out to provide the density criterion of thinning for the inducement of the ecological succession by analysing of vegetational structure in Artificial Forest, National Parks. Eleven plots(size is $20m{\times}20m$) were set up in the artificial forest such as Pinus koraiensis forest, Abies holophylla forest, Chamaecyparis obtusa forest, Populus tomentiglandulosa forest, and Larix kaempferi forest and in the natural forest such as Pinus densiflora community, Pinus densiflora-Quercus serrata community, and Quercus serrata community in Chiaksan, Songnisan, Deogyusan, and Naejangsan National Parks, Korea. We classified the artificial forest into undeveloped type of succession, type of alien young trees developing, and early phase type of succession based on the vegetational structure. According to the index of Shnnon's diversity(unit: $400m^2$), undeveloped type of succession was ranged from 0.9681 to 1.1323, type of alien young trees developing was ranged from 1.0192 to 1.1870, early phase type of succession was ranged from 1.3071 to 1.3892, and natural vegetation was ranged from 1.2202 to 1.3428, therefore early phase type of succession forest and natural vegetation are more higher than simple-layered artificial forest with one needle leaf tree species. The limit for the step-by-step thinning was in the range of 30~60%. In case of undeveloped type of succession, we should thin out from large trees throughout three phases, because alien species dominated high value 88~90% in canopy layer. In case of type of alien young trees developing, we should thin out from alien young trees such as Populus tomentiglandulosa throughout one or two phases, because alien species dominated high value 60~97% and young trees with saplings growing up in understory and shrub layer. In case of early phase type of succession, we should thin out from alien trees that compete with native species throughout one or two phases, because alien species dominated less than value 30%.

• Journal of Intelligence and Information Systems
• /
• v.16 no.2
• /
• pp.73-94
• /
• 2010

The attending system is a medical system that allows doctors in clinics to use the extra equipment in hospitals-beds, laboratory, operating room, etc-for their patient's care under a contract between the doctors and hospitals. Therefore, the system is very beneficial in terms of the efficiency of the usage of medical resources. However, it is necessary to develop a strong support system to strengthen its weaknesses and supplement its merits. If doctors use hospital beds under the attending system of hospitals, they would be able to check a patient's condition often and provide them with nursing care services. However, the current attending system lacks delivery and assistance support. Thus, for the successful performance of the attending system, a networking system should be developed to facilitate communication between the doctors and nurses. In particular, the nursing records in the attending system could help doctors monitor the patient's condition and provision of nursing care services. A nursing record is the formal documentation associated with nursing care. It is merely a data repository that helps nurses to track their activities; nursing records thus represent a resource of primary information that can be reused. In order to maximize their usefulness, nursing records have been introduced as part of computerized patient records. However, nursing records are internal data that are not disclosed by hospitals. Moreover, the lack of standardization of the record list makes it difficult to share nursing records. Under the attending system, nurses would want to minimize the amount of effort they have to put in for the maintenance of additional records. Hence, they would try to maintain the current level of nursing records in the form of record lists and record attributes, while doctors would require more detailed and real-time information about their patients in order to monitor their condition. Therefore, this study developed a system for assisting in the maintenance and sharing of the nursing records under the attending system. In contrast to previous research on the functionality of computer-based nursing records, we have emphasized the practical usefulness of nursing records from the viewpoint of the actual implementation of the attending system. We suggested that nurses could design a nursing record dictionary for their convenience, and that doctors and nurses could confirm the definitions that they looked up in the dictionary through negotiations with intelligent agents. Such an agent-based system could facilitate networking among medical institutes. Multi-agent systems are a widely accepted paradigm for the distribution and sharing of computation workloads in the scientific community. Agent-based systems have been developed with differences in functional cooperation, coordination, and negotiation. To increase such communication, a framework for a multi-agent based system is proposed in this study. The agent-based approach is useful for developing a system that promotes trade-offs between transactions involving multiple attributes. A brief summary of our contributions follows. First, we propose an efficient and accurate utility representation and acquisition mechanism based on a preference scale while minimizing user interactions with the agent. Trade-offs between various transaction attributes can also be easily computed. Second, by providing a multi-attribute negotiation framework based on the attribute utility evaluation mechanism, we allow both the doctors in charge and nurses to negotiate over various transaction attributes in the nursing record lists that are defined by the latter. Third, we have designed the architecture of the nursing record management server and a system of agents that provides support to the doctors and nurses with regard to the framework and mechanisms proposed above. A formal protocol has also been developed to create and control the communication required for negotiations. We verified the realization of the system by developing a web-based prototype. The system was implemented using ASP and IIS5.1.

• Korean Journal of Heritage: History & Science
• /
• v.48 no.3
• /
• pp.4-29
• /
• 2015

To protect cultural heritages from damage and destruction, evaluating the crime prevention environments is considered extremely important. This study analyzed the crime patterns related to cultural heritages, classified the crime environments by their types, and deduced the elements of the CPTED(Crime Prevention Through Environment Design), aiming to present the indices for evaluating the crime prevention environments. The results of this study can be summarized as follows. First, the crimes related to cultural heritages that must be prevented were identified as the night time trespassing and arson. According to the results of the analysis of external environments based on crime actions, the crime prevention environments of cultural heritages were classified into 10 types. Second, the important evaluation principles of the cultural heritage CPTED were the access control, surveillance reinforcement and the surrounding environment. Third, the access control that cover the internal region, boundary, external region and surroundings were classified into 22 indices. The surveillance reinforcement covers natural, organized and mechanical surveillance with 21 indices. Fourth, the applicability of the CPTED evaluation index was presented according to the types of the cultural crime prevention environments. The results confirmed that the maximum 43 indices were applicable to the seowon(lecture hall), hyanggyo(Confucian school), and gwana(district government office), and the minimum 10 indices, to the ramparts. Finally, the 43 indices were applied to Donam Seowon to validate their applicability. The results confirmed that most of the indices were applicable with the partial supplements. The evaluation index presented in this study is likely to contribute to studies in the cultural heritage CPTED field and to the protection of cultural heritages. Furthermore, this study is considered significant because it unleashed continuous concerns on and developments of CPTED. However, as the field survey to validate the applicability of the indices was limited to only one type, it may require further objective verification such as through an expert's examination of the validity and applicability of the evaluation index. In addition, to accommodate the index in related policies and systems, more precise verifications of the indices by type are considered necessary.

• Korean Journal of Heritage: History & Science
• /
• v.46 no.4
• /
• pp.48-63
• /
• 2013

The results of the study on the space planning and landscape design of Unjoru(雲鳥樓) through the 'Jeolla Gurye Omidong Gado(全羅求禮五美洞家圖)' drawn using GyeHwa(界畵) technique are as follows. First, 'Omidong Gado' is believed to date back to the period when Unjoru(1776~1783) was established for the following reasons: (1) The founder, Yoo-IJu(柳爾?), sent the drawing for the house while he was serving as the governor of YongCheon county(龍川府史). (2) It shows the typical dwelling houses' space division and its location is in a good spot with mountain in the back and water in front(背山臨水) and there is every indication of scheme drawing. (3) Front gate was changed and remodeled to a lofty gate in 1804. Second, Nogodan & Hyeongjebong of Jiri Mountain sit at the back of Unjoru, and faces Obong mountain and Gyejok mountain. In addition, the Dongbang stream flowing to the east well illustrates the Pungsu theory of mountain in the back and water in the front. Third, the house is structured in the shape resembling the character 品, divided into 5 areas by hierarchical order in the cross line from all directions. The site, which includes the outdoor yard and the back garden, consists of 5 blocks, 6 yards and 2 gardens. Fourth, the outdoor yard with aesthetical value and anti-fire function, is an ecological garden influenced by Confucianism and Taoism with a pond (BangJiWonDo Type, 方池圓島形) at the center. Fifth, the Sarang yard(舍廊庭) is decorated with terrace garden and flower garden, and the landscaping components such as oddly shaped stone, crane, plum, pine tree, tamarisk tree and flowering plants were used to depict the ideal fairy land and centrally placed tree for metaphysical symbolism. The upper floor of Sarangchae commands distant and medium range view, as well as upwards and downwards. The natural landscape intrudes inside, and at the same time, connects with the outside. Sixth, pine forest over the northern wall and the intentionally developed low hill are one of the traditional landscaping techniques that promotes pleasant residential environment as well as the aesthetics of balanced fullness.

• Journal of the Korean Society of Floral Art and Design
• /
• no.44
• /
• pp.33-51
• /
• 2021

This thesis analyzes the formal characteristics of Dutch flower still life from the 17th century to the early 18th century and looks into the relevance with the Dutch art market from a macro perspective. The 17th Flower Still Life is to represent social hierarchy in that as the imported exotic, recherch items, the flowers were classified in the terms of their rarity and expensiveness. For this intriguing research, the subject is circumscribed to a vase of flowers, which is the quintessence of In the form of various Dutch Flower Still Life. Dutch society in the early 17th century was centered on the civilian class engaged in trade and commerce, which allowed them to purchase art works to show off their wealth, economic benefits and satisfaction of aesthetic tastes. Among them, the popularity of flower still life was related to the concentrated demand for rare flowers from the new continent. Accordingly, exact depiction and sense of the three dimensional manner were highly regarded in the early flower still life. For the tastes of the wealthy citizens who succeeded in business, the identity of flowers and the actual screen were considered as important. However, after the mid 17th century, economic growth in the Netherlands put an end, and the art market was also on a downward path. The demand class of flower still life has gotten farther away from the spirit of businessmen and has changed into city aristocrats who were stable rentiers. Their tastes laid emphasis on subjective sensibility, which meant that aristocratic, asymmetric, and dramatic chiaroscuro were preferred rather than being realistic. Furthermore, in the 18th century illusionistic realism was abandoned as an expression method of the planar characteristics and a new era in the floral still life was ushered with the reinforcement of decorative effect. From this perspective, it is not an exaggeration to say that romanticism, which is thought of as the beginning of Contemporary Art, originated from the aesthetic taste of Dutch civic culture.