• Structural Engineering and Mechanics
• /
• 제83권6호
• /
• pp.799-810
• /
• 2022

This study investigated the effect of the strengthening efficiency of unbonded steel-bar truss system on the out-of-plane behavior of perforated masonry walls. Four full-scale unreinforced masonry (URM) walls with two different planes were prepared using the unbonded steel-bar truss system and a URM walls without strengthening. All masonry walls were tested under constant axial and cyclic lateral loads. The obtained test results indicated that the pinching effect in the out-plane behavior of masonry walls tends to decrease in the in- and out-of-plane strengthened URM walls using the unbonded steel-bar truss system with the higher prestressing force ratio (R_p) of vertical reinforcing bars in the unbonded steel-bar truss system, regardless of the perforated type of the masonry wall. Consequently, the highest maximum shear resistance and cumulative dissipated energy at peak load in the post-peak behavior were observed in the in- and out-plane strengthened URM walls with the highest R_p values, which are 2.7 and 6.0 times higher than those of URM. In particular, the strengthening efficiency of the unbonded steel-bar truss system was primarily attributed to the vertical prestressed steel-bars rather than the diagonal steel-bars, which indicates that the strains in the vertical prestressed steel-bars at the peak load were approximately 1.6 times higher than those in the diagonal steel-bars.

• 정보처리학회논문지B
• /
• 제10B권7호
• /
• pp.837-846
• /
• 2003

본 연구에서는 아파트의 설계도면을 처리의 대상으로 하고 있다. 이러한 아파트 도면은 굵고 평행한 두 개의 선으로 표현되는 주벽과 심볼(문, 창, 베란다. 타일 $\cdots$), 치수선(Dimension Line), 치수보조선, 여러 가지 수치를 나타내는 숫자(치수)와 문자 등으로 구성되어 있다. 본 연구에서는 이러한 아파트 도면 내에서 아파트 건물의 골격을 이루는 주벽을 인식하는 방법을 제시하고 있다. 이를 위해서 가는 라인을 제거하고 굵은 라인만을 남기는 이진화 방법을 사용하여, 이러한 라인들을 벡터화하고, 주벽의 존재위치를 한정하였다. 이를 이용해 치수보조선을 구하고 찾은 피수보조선을 이용하여 주벽을 검출하고, 찾아진 주벽에 연결되는 다른 주벽으로 영역을 확장해 나가는 방법을 구현하였다. 마지막으로, 주벽사이에 있는 창문은 비록 주벽이 아닌 창문 심볼로 표현되어 있더라도 주벽으로 인식해야 하기 때문에, 찾아진 주벽을 이용해 이들 주벽사이에 존재하는 창문을 찾는다. 실험결과 인식률에서 본 연구에서 제시하는 방법이 96.5%의 인식율을 나타내어 Karl Tombre 연구팀의 방법 90.7%보다 5.8% 더 우수하게 나타났고, 오인식의 수도 작게 나타났다.

• International Journal of Concrete Structures and Materials
• /
• 제18권1E호
• /
• pp.55-61
• /
• 2006

RC shear walls are frequently used as lateral force-resisting system in building construction because they have sufficient stiffness and strength against damage and collapse. If RC shear walls are properly designed and proportioned, these walls can also behave as ductile flexural members like cantilevered beams. To achieve this goal, the designer should provide adequate strength and deformation capacity of shear walls corresponding to the anticipated deformation level. In this study, the level of demands for deformation of shear walls was investigated using a displacement-based design approach. Also, deformation capacities of shear walls are evaluated through laboratory tests of shear walls with specific transverse confinement widely used in Korea. Four full-scale wall specimens with different wall boundary details and cross-sections were constructed for the experiment. The displacement-based design approach could be used to determine the deformation demands and capacities depending on the aspect ratio, ratio of wall area to floor plan area, flexural reinforcement ratio, and axial load ratio. Also, the specific boundary detailing for shear wall can be applied to enhance the deformation capacity of the shear wall.

• 한국지진공학회논문집
• /
• 제18권2호
• /
• pp.79-87
• /
• 2014

Masonry-infilled walls have been used in reinforced concrete(RC) frame structures as interior and exterior partition walls. Since these walls are considered as nonstructural elements, they were only considered as additional mass. However, infill walls tend to interact with the structure's overall strength, rigidity, and energy dissipation. Infill walls have been analyzed by finite element method or transposed as equivalent strut model. The equivalent strut model is a typical method to evaluate masonry-infilled structure to avoid the burden of complex finite element model. This study compares different strut models to identify their properties and applicability with regard to the characteristics of the structure and various material models.

• International Journal of Concrete Structures and Materials
• /
• 제10권sup3호
• /
• pp.19-31
• /
• 2016

The objective of this paper is to investigate the effect of thickness and moisture on temperature distributions of reinforced concrete walls under fire conditions. Toward this goal, the first three wall specimens having different thicknesses are heated for 2 h according to ISO standard heating curve and the temperature distribution through the wall thickness is measured. Since the thermal behavior of the tested walls is influenced by thickness, as well as moisture content, three additional walls are prepared and preheated to reduce moisture content and then tested under fire exposure. The experimental results clearly show the temperatures measured close to the fire exposed surface of the thickest wall with 250 mm thickness is the highest in the temperatures measured at the same location of the thinner wall with 150 mm thickness because of the moisture clog that is formed inside the wall with 250 mm of thickness. This prevents heat being transferred to the opposite side of the heated surface. This is also confirmed by the thermal behavior of the preheated walls, showing that the temperature is well distributed in the preheated walls as compared to that in non-preheated walls. Finite element models including moisture clog zone are generated to simulate fire tests with consideration of moisture clog effect. The temperature distributions of the models predicted from the transient heat analyses are compared with experimental results and show good agreements. In addition, parametric studies are performed with various moisture contents in order to investigate effect of moisture contents on the thermal behaviors of the concrete walls.

• Structural Engineering and Mechanics
• /
• 제75권3호
• /
• pp.389-399
• /
• 2020

An infill wall made of high-performance fiber-reinforced cementitious composites (HPFRCC) was utilized in this study to strengthen the reinforced concrete (RC) frame structures that had not been designed for seismic loads. The seismic performance of the RC frame structures strengthened by the HPFRCC infill walls was investigated through the experimental tests, and the test results showed that they have improved strength and deformation capabilities compared to that strengthened by the RC infill wall. A simple numerical modeling method, called the modified longitudinal and diagonal line element model (LDLEM), was introduced to consider the seismic strengthening effect of the infill walls, in which a section aggregator approach was also utilized to reflect the effect of shear in the column members of the RC frames. The proposed model showed accurate estimations on the strength, stiffness, and failure modes of the test specimens strengthened by the infill walls with and without fibers.

• Structural Engineering and Mechanics
• /
• 제25권4호
• /
• pp.365-382
• /
• 2007

A pilot study has been conducted to guide the development of a finite element modeling formulation for the analysis of architectural glass curtain walls under in-plane lateral load simulating earthquake effects. This pilot study is one aspect of ongoing efforts to develop a general prediction model for glass cracking and glass fallout for architectural glass storefront and curtain wall systems during seismic loading. For this study, the ANSYS finite element analysis program was used to develop a model and obtain the stress distribution within an architectural glass panel after presumed seismic movements cause glass-to-frame contact. The analysis was limited to static loading of a dry-glazed glass curtain wall panel. A mock-up of the glass curtain wall considered in the analysis with strain gages mounted at select locations on the glass and the aluminum framing was subjected to static loading. A comparison is made between the finite element analysis predicted strain and the experimentally measured strain at each strain gage location.

• 건축역사연구
• /
• 제30권1호
• /
• pp.7-17
• /
• 2021

Bang walls surround the four sides of Band in ancient capital cities of East Asia where the Bang system was in operation. There are ongoing research efforts for the structure of a capital city and Bang system around the capital of Silla, but there is a huge shortage of research on Bang walls. This study thus set out to examine Bang walls in the capital of Silla around the Hwangnyongsa Temple and its surroundings. The findings show that the Bang walls in the capital of Silla were built with a mix of earth and stone and with tiled roofs on top. The sizes of Bang walls were distinguished from the walls of individual structure groups inside Bang and closely related to the Bang size and the width of adjacent roads.

• 국제초고층학회논문집
• /
• 제3권1호
• /
• pp.9-19
• /
• 2014

In this study the seismic performances of reinforced concrete apartment buildings with Y- and box-shaped plans having central core are investigated. Three types of model structures are designed for each shape depending on the amount of shear partition walls: structures with all shear walls, structures with all columns except the core walls, and structures with shear walls and columns combined. The required amount of concrete to satisfy the specified design loads is the largest in the all shear wall structures, and decreases as more and more shear walls are replaced with columns. The amount of re-bars increased significantly in the flat plate structures. According to nonlinear static and dynamic analysis results, the structures with all shear walls and all columns turn out to have the largest and the smallest strengths, respectively. However it is observed that even the all-column structures with shear core have proper load resisting capacity for design level seismic load.

• 한국공간구조학회논문집
• /
• 제19권4호
• /
• pp.77-84
• /
• 2019

This study introduces a newly developed PC non-bearing wall system to prevent the damage of RC wall-type apartments that have been heavily damaged by the 2017 Pohang Earthquake. In order to evaluate the performance of the developed PC non-bearing wall system, a static cyclic test is conducted. The prototype of test specimen is from the RC wall-type apartment which has been severely damaged by the 2017 Pohang Earthquake. The specimen with the conventional non-bearing wall system showed the similar damage of RC wall type apartment suffered from the Pohang Earthquake. In case of the specimen with the developed PC non-bearing wall system, cracks and damages were not transmitted between the walls due to the seismic slit and there were almost no cracks in the non-bearing walls. Therefore, the proposed non-bearing wall system, separated from the structural walls, could prevent spreading cracks to bearing walls and make it possible to effectively control damage due to earthquake loads.