• KSTLE International Journal
• /
• 제6권1호
• /
• pp.1-7
• /
• 2005

Wear model for predicting the vehaviour of a depth is considered in this paper. It is deduced from the energy and volume based wear models such as the Archard equation and the workrate model. A new parameter of the equivalent depth ($D_e$= wear volume /worn area) is considered for the wear model of a depth prediction. A concenpt of a dissipated shear energy density is accommodated for in the suggested models. It is found that $D_e$ can distinguish the worn area shape. A cubic of $D_e$($D_e^3$) gives a better linear regression with the volume than that of the maximmum depth $D_{max}e$($D_{max}^3$) does. Both $D_{max}$ and $D_e$ are used for the presently suggested depth-based wear model. As a result, a wear depth profile can be simulated by a model using $D_{max}$. Wear resistance from the concern of an overall depth can be identified by the wear coefficient of the model using $D_e$.

• Tribology and Lubricants
• /
• 제16권5호
• /
• pp.357-364
• /
• 2000

In this study, the sliding wear in spur gears, using Archard's wear model, is analyzed. Formulas of tooth sliding wear depth along the line of action are derived. The tooth profile is modified Id make a smooth transmission of the normal loads and the cylinder profile for reducing the pressure spike is suggested. The sliding wear rate is calculated with these profiling results. We expect these modification methods to contribute to the reduction of sliding wear not only in the root, but the tip of tooth and tooth edge.

• Tribology and Lubricants
• /
• 제33권3호
• /
• pp.98-105
• /
• 2017

A pin-on-disk test is performed to measure the wear volume of a ductile cast iron (DCI) roll when it wears down using a high carbon steel and two alloy steels at different sliding velocities between the roll and the material (steel). Normal pressure is set as constant and test temperatures are 400, 500 and $600^{\circ}C$. In addition, thermal softening behavior of the DCI roll is examined using a high-temperature micro-hardness tester and the surface hardness variation of the DCI roll is expressed in terms of temperature and heating time. Based on experimental data, a wear coefficient used in Archard's wear model for each material is obtained. The wear volume is clearly observed when the test temperature is $400^{\circ}C$ and sliding velocity varies. However, it is not measured at temperatures of $500^{\circ}C$ and $600^{\circ}C$ even with variations in sliding velocity. From the optical photographs of the pin and disk, the abrasive wear is observed at $400^{\circ}C$ clearly, but no at $500^{\circ}C$ and $600^{\circ}C$. At higher temperatures, the pin surface is not smooth and has many tiny caves distributed on it. It is found that wear volume is dependent on the carbon contents rather than alloy contents. Results also reveal that the variations of wear coefficients are almost linearly proportional to the carbon contents of the material.

• 소성∙가공
• /
• 제7권3호
• /
• pp.274-281
• /
• 1998

The service life of tools in metal forming process is to a large extent limited by wear, fatigue fracture and plastic deformation. In elevated temperature forming processes wear is the predominant factor for tool operating life. To predict tool life by wear Achard's model is generally applied. Usually hardness of die is considered to be a function of temperature. But hardness of die is a function of not only tem-perature but also operating time of die. To consider softening of die by repeated operation it is necessary to express hardness of die by a function of a function of temperature and time. By experiment of reheating of die softening curve was obtained and applied to suggest modified Archard's Model in which hardness is a function of main tempering curve.

• 한국정밀공학회지
• /
• 제13권1호
• /
• pp.116-122
• /
• 1996

In forming processes, die failure must be considered before die design. One of the main reasons of die failure in industrial application of metal forming technologies is wear. The die wear affects the tolerances of formed parts, metal flow and costs of processes etc. The only way to control these failures is to develop methods which allow prediction of the die wear and which are suited to be used in the design state in order to optimize the process. In this paper, wire drawing processes were simulated using the rigid-plastic finite element method and its results were used for predicting the die wear by Archard's wear model. The effects of the temperature rising on the wear profiles of die were also investigated. The simulation results were compared with the measured die profiles.

• 소성∙가공
• /
• 제26권3호
• /
• pp.137-143
• /
• 2017

In this study, a wear test method was proposed to predict the wear life of the CrN layer coated on the surface of the press tools for manufacturing the auto-parts with ultra high strength steel (UHSS) with a tensile strength of 1.5 GPa. The pin-on-disc type wear test was carried out to confirm the feasibility and the reproducibility of the wear amount according to the test conditions such as the normal force, the sliding velocity, and the sliding speed. The test conditions were obtained from the finite element stamping analysis and the wear simulation. With the wear amount from the wear test, a prediction model of the wear depth in the CrN coating layer was proposed according to the test conditions with the design of experiments such as Taguchi method and the response surface method. The derived prediction model was then compared to the result of the Archard wear model, fully describing that the proposed model can effectively predict the wear life of the press tools for the auto-parts with UHSS.

• 대한기계학회논문집A
• /
• 제35권9호
• /
• pp.983-989
• /
• 2011

본 연구에서는 경제요소법을 이용한 프레팅 마멸 예측을 위한 수치적 알고리즘을 개발하였다. 반무한체 해석을 통해 사각조각면위의 균일분포하중과 탄성변형량의 관계로부터 접촉 계면의 응력을 계산하였고 Archard wear 모델을 이용해 각 격자의 마멸 깊이를 계산하여 접촉면의 형상을 예측할 수 있는 알고리즘을 제시하였다. 본 연구의 정확성을 검증하기 위해 McColl 등의 연구와 비교하였고 개발된 알고리즘을 구접촉 모델에 확장하여 그 유용성을 확인하였다. 아울러 프레팅 해석의 효율적인 계산을 위해 한 step당 사이클 증가량인 step cycle이 해의 정확성에 미치는 영향을 검토하여 step cycle 설정의 중요성을 제시하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 춘계학술대회논문집
• /
• pp.67-70
• /
• 2000

The tool life is not long enough under sever forming condition in warm forging. The tool life is affected by wear heat fatigue plastic deformation and so on. Especially wear is one of the most serious factors for tool life. To increase tool life we should consider various factors like processing design die design die materials lubrication and cooling system This study design to obtain the steady state temperature of die by FEM analysis under several conditions of cooling. There are four cooling conditions in this study no cooling internal cooling external cooling and both internal and external cooling. With above obtained temperatures tool life is predicted using Archard's model that is considered softening of die. The effect of internal cooling system is better than that of externally cooled die. To predict the die life the steady state temperature is calculated by using mean temperature of die. Considering only wear the die life much longer as the cooling effect is bigger. The more accurate die life will be predicted if we consider heat crack as well as wear.

• Design & Manufacturing
• /
• 제7권1호
• /
• pp.28-33
• /
• 2013

During the cold forming, due to high working pressure acting on the die surface, failure mechanics must be considered before die design. One of the main reasons of die failure in industrial application of metal forming technologies is wear. The mechanisms of wear are consisted of adhesion, abrasion, erosion and so on. Die wear affects the tolerances of formed parts, metal flow, and costs of process. The only way to control these failures is to develop a prediction method on die wear suitable in the design state in order to optimize the process. The wear system is used to analyse 'operating variables' and 'system structure'. In this study, with AISI D2, AISI 1020, AISI 304SS materials, a series of the wear experiments of pin-on-disk type to obtain the wear coefficients from Archard's wear model and the upsetting processes are carried out to observe the wear phenomenon during the cold forming process. The analysis of upsetting processes are performed by the rigid-plastic finite element method. The result of the analysis is used to investigate the die wear the processes, and the analysis simulated die wear profiles are compared with the experimental measured die wear profiles.

• 대한기계학회논문집A
• /
• 제26권9호
• /
• pp.1736-1745
• /
• 2002

The objective of this study is to predict the roll wear in hot rod rolling process. In this study hot rod rolling process for round and oval passes has been investigated. In order to predict the roll wear, the wear model is reformulated as an incremental form and then wear depth of roll is calculated at each deformation step on contact area using the results of finite element analysis, such as relative sliding velocity and normal pressure at contact area. Archard's wear model was applied to predict the roll wear. To know the thermal softening of DCI (Ductile Cast Iron) roll according to operating conditions, high temperature micro hardness test is executed and a new wear model has been proposed by considering the thermal softening of DCI roll expressed in terms of the main tempering parameter curve. 3D wear program developed in this study might be used for adjusting the gap of rolls to set up a suitable rolling schedule for keeping dimensional tolerance of the product.