• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.8
• /
• pp.299-307
• /
• 2013

In this paper, design of UWB Antenna which propagate impulse by pulse fidelity and distortion equation was induced and applied. UWB Antenna which has directional characteristic in UWB band should have low radiation loss and impulse radiation distortion. As a result, the paper designed wide band impedance transformer and microstrip slotline transit region structured antenna feeder line. By using the fabricated UWB antenna, the radiation pattern was measured in the radio anechoic chamber. Pulse fidelity of impulse radiation show good results more than 93% within ${\pm}30^{\circ}$ beam width.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.12
• /
• pp.1212-1218
• /
• 2014

This paper proposes a planar bow-tie UWB antenna by modifying the ground patch of a reference bowtie-monopole antenna satisfying low band of UWB. The proposed antenna was implemented with five-angled ground patch to be operated in whole UWB band, while the reference antenna had a ground patch of half circle type. The measured return loss satisfies less than -10 dB in 3.1~10.6 GHz, except 4.9~5.8 GHz rejection band. The measured radiation pattern is almost the same with that of the monopole antenna. The radiation gain reduction is about 8 dB at rejection band.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.3
• /
• pp.43-51
• /
• 2020

In this paper, the design of 64 array antennas applied to RWP (Radar Wind Profiler) was described. The design point of the antenna is to ensure isolation between each element and to match the vertical / horizontal radiation pattern. To this end, a single element of the array antenna was proposed as a Bend dipole type, and through simulation, When sequentially sending 5 beams including vertical, the east/west/south/north direction was ±20°, and it was confirmed that no Grating Lobe occurred when steering the beam. The 64 array antenna proposed in this paper was designed with performance equal to or higher than that of overseas products, and was confirmed to be applicable to RWP.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.1
• /
• pp.106-113
• /
• 2011

In this paper, the non-resonant SWG(Slotted Waveguide) antenna with double slots in narrow wall of rectangular waveguide is designed. Because energy radiated from each slot depends upon inclination angle of slot of the designed antenna, inclination angle of each slot is controlled to satisfy the amplitude distribution for required sidelobe level. Instead of the conventional extraction method of slot conductance, this amplitude distribution is made by the proposed method, which employs far-field radiation pattern calculated by Fourier transform of aperture field distribution on slot. The non-resonant double SWG antenna is designed by the proposed method and is manufactured. The antenna performances are measured and compared with the simulated results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.4
• /
• pp.381-386
• /
• 2014

In this paper, the effect of slot antenna's location in the radiation performance and impedance bandwidth was analyzed. The proposed antenna was designed to operate at Wi-Fi band(2.4~2.5 GHz) when the slot antenna is located at the center of the ground plane, the proposed antenna has a bandwidth of 340 MHz(2.24~2.58 GHz) under voltage standing wave ratio of = 2 and achieves average realized efficiency of 69 % over Wi-Fi bands.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.2
• /
• pp.197-205
• /
• 2017

During the sea trial, we discovered EMI between MOSCOS and ES DF antenna. CW emitted by MOSCOS raised the threshold level of ES DF antenna. As a result, direction finding rate of ES has been decreased. This is a study for the improvement of EMI between the antennas mounted on a surface ship. An analysis is accomplished for MOSCOS, ES DF antenna and Jamming transmitter. This paper presents the method how to solve EMI based on the measurements and calculations about the ES DF antenna receiving level, MOSCOS radiation pattern and Jamming transmitter thermal noise. The test was performed with optimal deployment of MOSCOS on a surface ship. After changing the position of MOSCOS, EMI has been decreased significantly.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.219-223
• /
• 2003

This paper describes an estimation of DOA(Direction Of Arrival) measurement system using DBF receiver with linear array antenna. This DBF receiver is composed of resistive FET mixer using low IF mettled. A radio frequency(RF), a local oscillator(LO) and ail intermediate frequency(IF) considered in this research are 2.09 GHz, 2.08 GHz and 10 MHz, respectively. This receiver is composed of a band-pass filter, a low-pass filter, a DC bias circuit. DOA measurement system is consist of linear array antenna, DBF receiver, AD control box and computer in the anechoic chamber. Receiving antenna is 4-array monopole antenna and DBF receiver is 4-Ch resistive FET mixer without amplifier. DOA algorithm is implemented using MUSIC algorithm with high resolution. We show that the results of DOA is $-30^{\circ},\;0^{\circ}$ and $60^{\circ}$, respectively. And we know that DOA estimation error occur by antenna radiation pattern and fabrication error of antenna array.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.1
• /
• pp.131-134
• /
• 2012

A bar-code shape UHF RFID tag antenna is designed and fabricated with silver conductive ink. It can be recognize by both bar-code scanner and RFID reader. The bar-code shape is taken from a general box of a product, and the product code of the bar-code is used for the antenna design. The tag antenna is fabricated with silver conductive ink using a T-matching structure. The designed tag antenna is satisfied with bar-code system and RFID system simultaneously. The input reflection coefficient characteristics and the reading range pattern are measured. The peak reading range is about 111 cm, which is long enough.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.9A
• /
• pp.1083-1090
• /
• 2004

In this paper, a meander-type microstrip patch antenna for application in 5GHz-hand is designed and fabricated To obtain enough bandwidth in VSWR≶2, the foam is inserted between substrate and ground plane, the coaxial probe source 1S used Antenna is simulated varing the length and width of meander line, the position of probe feeding and the thick of airgap. Later antenna is fabricated with optimizated antenna parameter. The measured result of Fabricated antenna obtained IGHz(l7.5%) bandwidth in VSWR≶2, the gain of 7.3-9.5dBi, Unidirectional pattern.

• Aerospace Engineering and Technology
• /
• v.5 no.2
• /
• pp.108-113
• /
• 2006

This paper includes the test results of KOMPSAT-2 payload downlink system which were measured for the purpose of performance verification. The antenna beam patterns which indicates the status of the interface & antenna itself, were measured as well as the antenna VSWR. The checkout of the transponder & its spectrum was followed and this made sure that there was no spurious output distinguished. Finally a test for BER verification was conducted between satellite and receiving system for their compatibility through the antenna-to-antenna connection using an antenna hat. Verification tests for an RF system should be performed after relocation, integration and test for environments in order to make sure that no degradation happens.