• 한국세라믹학회지
• /
• 제53권5호
• /
• pp.535-540
• /
• 2016

Effects of compositions and sintering conditions on glaze properties are shown in the diagram constructed by using the unity molecular formula (UMF) method in this study. Glossy characteristics of glaze were clearly differentiated by compositional area in the diagram and sintering process. As alumina and silica contents were increased, texture of the glaze became rough and opaque, akin to having been devitrified or underfired. The correlation between glossiness and surface roughness was found to be non-linear and inversely proportionate. Crystalline phases formed in the glaze were also influenced by the compositional area. Due to the high concentration of CaO, anorthite and wollastonite were formed depending on the compositions. Hardness was increased with an increase of alumina and silica concentrations in the glaze.

• 에너지공학
• /
• 제11권2호
• /
• pp.149-159
• /
• 2002

분류층 가스화기에서 슬래그의 점도 변화는 가스화기 운전조건을 결정하는 중요한 요소이다. 본 논문에서는 국내 가스화 대상탄으로 선정된 9개 탄의 슬래그 점도를 가스화 조건에서 측정하였고 점도 변화에 영향을 미치는 슬래그내의 결정체의 크기와 종류를 관찰하였다. 시료는 고둥기술원 건식 가스화기에서 배출된 슬래그 시료를 사용하였다. 9개탄 중 Alaska Usibelli, Curragh, Drayton, Adaro, Baiduri탄 슬래그는 결정슬래그의 경향을 보여주었고, Datong탄과 Cypurus탄 슬래그는 유리슬래그이였다. 결정슬래그외 경우 $T_{cv}$ +$50^{\circ}C$를, 유리슬래그의 경우 $T_{1000}$poise/+$50^{\circ}C$를 가스화기의 최저운전온도로 정의하였을 때 Denisovsky 탄이 가장 높은 온도를, Drayton탄이 가장 낮은 온도를 필요로 하였다. 모든 슬래그가 가스화기 내화물성분인 C $r_2$ $O_3$를 포함하고 있었고, 132$0^{\circ}C$ 주위에서 $T_{cv}$ 를 갖는 결정슬래그의 경우(Alaska Usibeli, Curragh, Adaro탄) 냉각중에 형성됨을 나타내는 커다란 anorthite이 주 결정상으로 나타나 anorthite의 형성이 점도의 급격한 상승의 원인이 됨을 확인하였다. 또한 기포를 갖고 있는 Denisovsky탄의 경우 기포가 산화철의 환원에 의해 형성됨을 추정할 수 있었다..

• 한국광물학회지
• /
• 제3권1호
• /
• pp.1-6
• /
• 1990

Clacic amphiboles along the tremolite (Tr)-tschermakite(Ts) joint were synthesized using a piston-cylinder appratus. At 750-85$0^{\circ}C$and 12-2 kb, amphibole+corundum coexist with zoisite($\pm$talc, chlorite, and Mg-staurolite), but with anorthite($\pm$cholorite, spinel, pyroxenes, and sapphirine) at lower P. At 90$0^{\circ}C$, amphibole+corundum+clinopyroxene($\pm$anorthite, forsterite, sapphirine, and garnet) are stable over the P range 12-18 kb. These amphibole-bearing assemblages are replaced at high P by clcinopyroxene+talc+chlorite+zoisite at 650-75$0^{\circ}C$, and at higher temperatures by garnet+clinopyroxene($\pm$zoisite, orthopyroxene, and Mg-staurolite). Synthetic amphiboles with Ts>~45 mol% contain as much as 0.15 excess cations per formula unit(pfu) based on 23 oxygens(anhydrous formula), whereas less tschermakitic ones are deficient in cation occupancy by up to 0.18 pfu. This trend is attributed to the 야/trioctahedral substitution in Ca-amphiboles. Compositions of synthetic amphiboles display systematic changes with P and T governed by coexisting mineral assemblages. The Ts content (=[8-Si-Na]/2) increases with increasing T( Ts/ T=~0.1 nik% K-1) in the range 750-85$0^{\circ}C$, but remains nearly constant at 850-90$0^{\circ}C$. Pressure dramatically affects the Ts content of Ca-amphiboles:it increases with P at 8-12 kb( Ts/ T=2-3 mol% K-1), but significantly decreases at 12-21 kb( Ts/ P=-2.5 mol% Kb-1). Hence, the most tschermakitic amphiboles, containing 60$\pm$5 mol % Ts, or 1.2$\pm$0.1 tetrahedral Al, occur at 12 kb and 850-90$0^{\circ}C$. Compositions of Ca-amphiboles defined by a simple reaction, 3 Tr+2 zoisite+7 corundum+H2O=5 Ts, are reversed and used to estimate thermodynamic parameters of tschermakite assuming ideal mixing of Tr-Ts solid solutions. Predicted standard molal entropy and enthalpy of tschermakite are : S$^{\circ}$of Tr-Ts solid solutions. Predicted standard molal entropy and enthalpy of tschermakite are : S$^{\circ}$=566.9$\pm$13.7 J mol-1K, -1and H$^{\circ}$=-12518.36$\pm$15.17 kJ mol.-1

• 한국세라믹학회지
• /
• 제13권2호
• /
• pp.31-38
• /
• 1976

Korean tremoitic talc, wollastonite and clay have been used to develop a wall tile body to appropriate to the fast firing process. Some of ceramic properties of the raw materials were investigated by X-ray diffraction, thermal analysis and chemical analysis. The body compositions were formulated from the range of 35~75% tremolitic talc, 0~30% wollastonite and 25~35% plastic clay. Thermal gravity analysis and thermal expansion were tested for each of unfired bodies to study the correlation between thermal dehydration and linear shrinkage during the firing procedure. Linear shrinkage and water absorption of the fired bodies at the various temperature were taken as a measures for determining the proper firing range of the bodies. Increasing the content of wollastonite and firing temperature, the thermal expansion of the fired body showed the gradual decrease, and the thermal expansion curves showed a tendency to straighten. These observations may be resulted from the fact that the amounts of diopside and anorthite formed were gradually increased and those of quartz relatively decreased. The optimum compositions of the wall tile bodies for fast firing are 30% clay, 10~20% wollastonite and 50~60% tremolitic talc.

• 한국연소학회지
• /
• 제14권3호
• /
• pp.16-23
• /
• 2009

It is strongly desired for coal-fired power plants to utilize not only low-rank coals with high moisture contents, but also lowering cost with diversifying fuel sources. In this study, combustion characteristics of low rank coal with high moisture, and standard pulverized coals are experimentally investigated using TGA (Thermogravimetric Analysis) and DTF (drop tube furnace). The coals tested are three kinds of coal with moisture content ranging from 8.32 to 26.82%. The results show that under the air combustion condition, the burn-out time at TGA rises as moisture content increases, and standard pulverized coal with 8.32% moisture content showed the lowest activation energy of 55.73 kJ/mol. In case of the high amount of moisture, the combustion efficiency decreases due to evaporation heat loss, and unburned carbon in ash produced at combustion process in DTF increased. Aslo, initial deformation temperature of slag attached in alumina tube of DTF decreased with lowering the crytallinity of anorthite and augite. To improve the combustion reactivity and efficiency, it is effective to upgrade through drying the high moisture coal to moisture level (less than 10%) of standard pulverized coal.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.848-851
• /
• 2009

석탄슬래그는 회분의 조성에 따라 고온에서 매우 상이한 슬래그 거동을 보여준다. 국내 가스화 대상탄으로 검토된 탄 중, 산성 산화물의 함량이 높아 고용융점을 갖는 7종의 석탄 회분을 가스화 조건인 고온, 환원분위기에서 점도 측정을 실시하였다. 4종의 탄에 대해서는 높은 점도를 낮추기 위하여 염기성 산화물인 CaO를 3가지 비율로 혼합하여 점도 측정을 실시하였다. 또한, flux의 혼합으로 인해 발생할 수 있는 결정체 형성을 FactSage 평형계산 프로그램과 CaO-SiO2-Al2O3 3성분계 상평형도를 이용하여 예측하였다. CaO가 첨가된 시료 모두에서 낮은 CaO 첨가비에서는 원래의 시료보다 낮은 점도를 보였으나, CaO첨가비가 20% 이상일 때는 anorthite이 형성되어 $T_{cv}$를 갖는 결정슬래그로 점도 거동이 변화하면서 실제조업 가능한 온도를 증가시켰다. 점도 측정 후 냉각된 시료의 SEM/EDX 분석을 통해 형성된 결정체를 관찰한 결과, FactSage와 상평형도에서 예측된 결정체와 유사하게 나타나 CaO-SiO2-Al2O3 3성분계 상평형도가 결정체 예측에 유용함을 확인하였다.

• 한국광물학회지
• /
• 제9권1호
• /
• pp.43-53
• /
• 1996

The detailed crystal chemistry of ilmenite from the Hadong massif was studied by the EPMA, M ssbauer spectroscopy, and Rietveld structural refinement using X-ray powder diffraction data. The ilmenite-bearing anorthosite shows complicated mineral assemblage which consists of plagioclase, clinopyroxene, hornblende, biotite, chlorite, apatite, allanite, and zircon. Anorthite is andesine in composition (Ab 28-57), and clinopyroxene drops in ferro-hypersthene (Fs 62-70). Ilmenite is trigonal symmetry with R space group, whose structure shows the alternation of Fe2+ (M1 site) octahedral layer and Ti (M2 site) layer along c axis. M ssbauer spectroscopy indicates that there are three doubles which assigned to couple of Fe2+($\delta$=0.812, 0.890mm/sec) and one Fe3+($\delta$=0.303mm/sec) in octahedral sites. Their Fe3+/$\Sigma$Fe is 0.065 and chemical formula is established as Fe2+0.94Fe3+0.07Ti0.97O3 using both EPMA and M ssbauer analysis. Rietveld structural refinement reveals that site occupancies of Fe in M1 and Ti in M2 are 91.2% and 89.4%, respectively. This implies that Ti and Fe2+ are alternatively occupy M1 and M2 sites. In addition, smaller M2 site is more preferable to Fe3+ occupancy over M1.

• 한국세라믹학회지
• /
• 제52권1호
• /
• pp.41-47
• /
• 2015

Celadon shards from Gangjin and Buan were analyzed for their color, chemistry and microstructures. They exhibited similar chromatic characteristics in a $CIEL^*a^*b^*$ analysis. All of the glazes assessed showed comparable compositional areas, while the bodies from Gangjin shards had higher $RO_2$ concentrations. A high degree of similarity was also noted in the microstructures of the glaze and bodies from both regions. Anorthite crystals appeared in the glaze layer, and phase separation behavior developed around these crystals. This may have been caused by the glaze chemistry and the sintering process given the lengthy heating and cooling time. A Raman analysis indicated higher isolated $SiO_4$ unit ($Q_0$) values for the Buan samples. This can stem from the higher firing temperature or the longer sintering process.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권1호
• /
• pp.95-101
• /
• 1995

Crystallizable glasses with precipitation of celsian, anorthite, wollastonite and gahnite were prepared for the purpose of insulating dielectric layers in devices such as integrated circuit substrates. The starting glasses were prepared by melting the batches for 1 hour at 1450.deg. C and then Quenching to a distilled water. And crystallization behavior of these glasses were studied by DTA, TMA, XRD analysis and by the measurement of dielectric properties. The overall composition of the glass-ceramic consists in weight percent of 30-35% A1$_{2}$O$_{3}$, 13-26% BaO, 5-21% CaO, 10-24% ZnO, 4.5-9.0% TiO$_{2}$ and 4-8% B$_{2}$O$_{3}$. As a result, in barium-rich glasses only celsian phase was developed in the range of 850-900.deg. C. Also, the thermal expansion coefficient, dielectric constant and quality factor of these glass-ceramics were 68*10$^{-7}$ /.deg. C, about 9 and more than 1000, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.208-208
• /
• 2008

Micro patterning of conductor line/space on LTCC green sheet in the LTCC module is an important process for miniaturization in 3D integrated circuits. This work presented the effect of inorganic binders on the microstructure, adhesion, electrical resistivity, shrinkage and line/space resolution, which is a part of study in photoimageable conductor paste. The photoimageable conductor paste contains silver powder, polymer binder, monomer, photo-initiator, UV absorber, and solvent. The inorganic binders were furnished with varied weight percentage of anorthite, diopside and MLS-62 glass frits from 0% to 7%. The Line/space sizes thus obtained was under 25 micron.