• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.66 no.4
• /
• pp.263-266
• /
• 2017

In this study, the characteristics of anti-pollution coatings on glass substrates through annealing treatment were investigated. To investigate the change of properties by coating method and number of annealing treatment, after the anti-pollution coating was performed on the surface of glass substrate in three ways, the annealing treatment was performed by setting three kinds of annealing treatment conditions. The annealing treatment method is a torch using gas, which is advantage in that it can be installed directly on the site in an easy way compared with a annealing treatment process which is generally difficult. The anti-pollution properties, contact angle, transmittance, hardness, and adhesion of films on glass substrate were measured under 9 conditions of combination of coating methods and annealing treatment conditions. It was confirmed that as the number of annealing treatment increases, the anti-pollution property of the film synthesized on glass substrate becomes better.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.2
• /
• pp.99-102
• /
• 2015

Thin film transistors (TFTs) with amorphous 2 wt% silicon-doped zinc tin oxide (a-2SZTO) channel layer were fabricated using an RF magnetron sputtering system, and the effect of post-annealing treatment time on the structural and electrical properties of a-2SZTO systems was investigated. It is well known that Si can effectively reduce the generation of oxygen vacancies. However, it is interesting to note that prolonged annealing could have a bad effect on the roughness of a-2SZTO systems, since the roughness of a-2SZTO thin films increases in proportion to the thermal annealing treatment time. Thermal annealing can control the electrical characteristics of amorphous oxide semiconductor (AOS) TFTs. It was observed herein that prolonged annealing treatment can cause bumpy roughness, which led to increase of the contact resistance between the electrode and channel. Thus, it was confirmed that deterioration of the electrical characteristics could occur due to prolonged annealing. The longer annealing time also decreased the field effect mobility. The a-2SZTO TFTs annealed at 500℃ for 2 hours displayed the mobility of 2.17 cm²/Vs. As the electrical characteristics of a-2SZTO annealed at a fixed temperature for long periods were deteriorated, careful optimization of the annealing conditions for a-2SZTO, in terms of time, should be carried out to achieve better performance.

• Corrosion Science and Technology
• /
• v.14 no.6
• /
• pp.296-300
• /
• 2015

ALDC8 (Al-Si-Cu) alloy has been often corroded with pattern of intergranular corrosion in corrosive environments. Thus, in order to improve its corrosion resistance, the effect of annealing heat treatment to corrosion resistance and hardness was investigated with parameters of heating temperatures such as $100^{\circ}C$, $200^{\circ}C$, $300^{\circ}C$, $400^{\circ}C$ and $500^{\circ}C$ for 1hr. The hardness was varied with annealing temperature and slightly decreased with annealing heat treatment. However, the relation between annealing temperature and hardness agreed not well each other. Corrosion potential was shifted to noble direction and corrosion current density was also decreased with increasing annealing temperature. Moreover, both AC impedance at 10 mHz and polarization resistance on the cyclic voltammogram curve were also increased with increasing annealing temperature. Furthermore, intergranular corrosion was somewhat observed in non heat treatment as well as annealing temperatures at $100^{\circ}C$, $200^{\circ}C$ and $300^{\circ}C$, while, intergranular corrosion was not nearly observed at annealing temperature of $400^{\circ}C$, $500^{\circ}C$. Consequently, it is considered that the annealing heat treatment of ALDC8 alloy may be an available method not only to inhibit its intergranular corrosion but also to improve its corrosion resistance.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.251.1-251.1
• /
• 2013

Combination of oxidative vacuum annealing and oxygen plasma treatment can serve as a simple and efficient method of line-width modification of imprinted nanopatterns. Since the vacuum annealing and oxygen plasma could lead mass loss of polymeric materials, either one of the process can yield a narrowed patterns. However, the vacuum annealing process usually demands quite high temperatures (${\geq}300^{\circ}C$) and extended annealing time to get appreciable line-width reduction. Although the plasma treatment may be considered as an effective low temperature rapid process for the line-width reduction, it is also suffering for the lowered controllability on application to very fine patterns. We have found that the vacuum annealing temperature can be lowered by introducing the oxygen in the vacuum process and that the combination of oxygen plasma treatment with the vacuum annealing could yield the best result in the line-with reduction of the imprinted polymeric nanopatterns. Well-defined line width reduction by more than 50% was successfully demonstrated at relatively low temperatures. Furthermore, it was verified that this process was applicable to the nanopatterns of different shapes and materials.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.629-632
• /
• 1995

The formability of an automobile body panel is very important. So, we performed an annealing condition change for the development of annealing condition with temperature, atmospheric gas and the annealing cycle. Formability was changed under the influenced of the mechanical properties of steel sheet for the automobile body panel. Therefore, ot os important in the BAF(Batch annealing furnace) annealing process. Because mechanical properties were decided on the heat treatment method of the coil. So, we tested the development of mechanical properties according to the heat treatment method at the annealing furnace using the Ax atmospheric gas and the HNx atmospheric gas. As a result of several investigations, we confirmed the following characteristics ; mechanical properties change under the influence of the annealing cycle and atmospheric gas.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.2
• /
• pp.108-114
• /
• 1998

Development on the mechanical properties of steel sheet for the automobile body panel is very important in the BAF(Batch annealing furnace) annealing process. Because of the heat treatment method in the BAF, mechanical properties was decided on the heat treatment method of the coil. So, we tested on the development of mechanical properties according to heat treatment method at the annealing furnace using the Ax(H$_2$75%, $N_2$25%) atmospheric gas and the HNx(H$_2$4%, $N_2$96%) atmospheric gas. As a result of several investigations. We confirmed the following characteristics ; mechanical properties was changed under the influence of the annealing cycle, the heat treatment method and the atmospheric gas. And, elongation in the HNx BAF was better than the Ax BAF. Finally, most important thing in the BAF is using of proper annealing cycle in order to get a good quality.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.426-429
• /
• 2003

In this study, phase transformation characteristics of Nitinol shape memory alloy with 54.5wt%Ni-45.5wt%Ti were investigated by varying with annealing treatment and cutting conditions through DSC(differential scanning calorimetry). Annealing treatment conditions were considered as heat treated time of 5 min, 15 min, 30 min, and 45 min, heat treated temperature of 40$0^{\circ}C$, 50$0^{\circ}C$, 5$25^{\circ}C$, 55$0^{\circ}C$, 575$^{\circ}C$, $600^{\circ}C$, $700^{\circ}C$, 80$0^{\circ}C$, and 90$0^{\circ}C$, and environmental condition of heat treatment under vacuum or air. Cutting conditions were considered as no cutting, one side cutting, and two side cutting. Tensile test was also conducted on Nitinol shape memory alloy to investigate thermomechanical characteristics by varying with annealing heat treatment histories. According to the results, annealing treatment and cutting conditions were found to significantly affect on phase transformation and thermomechanical characteristics of Nitinol shape memory alloy.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.3
• /
• pp.103-108
• /
• 2005

ZnO thin films on (001) sapphire substrates have been deposited by pulsed laser deposition(PLD) technique using an Nd:YAG laser with a wavelength of 266nm. Before post-annealing treatment in the oxygen ambient, the experiment of the deposition of ZnO thin films has been performed for substrate temperatures in the range of $300\~450^{\circ}C$ and oxygen gas flow rate of $100\~700\;sccm$. In order to investigate the effect of post-annealing treatment of ZnO thin films, films have been annealed at various temperatures after deposition. After post-annealing treatment in the oxygen ambient, the structural properties of ZnO thin films were characterized by X-ray diffraction(XRD), scanning electron microscopy(SEM) and the optical properties of the ZnO were characterized by photoluminescence(PL).

• Applied Biological Chemistry
• /
• v.34 no.2
• /
• pp.187-189
• /
• 1991

Gelatinization temperatures of upland and lowland waxy brown rice starches annealed at $25^{\circ}C$ and $60^{\circ}C$ for 24hr were investigated with differential scanning calorimetry No annealing effect was observed at low temperature. The upland rice starch showed narrower range of gelatinization temperature upon annealing treatment at $60\circ}C$ compared with the lowland rice starch. The enthalpy of gelatinization was not changed in case of the upland rice starch but was increased in case of the lowland one upon annealing.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.99-102
• /
• 2003

Tin dioxide thin films were deposited at $375^{\circ}C$ on alumina substrate by metal-organic chemical vapor deposition process to find the relationship between physicochemical properties and the annealing treatments. The small grains with heat treatments grew to the bunch of grains and then showed the hillocks on the film surface. The thickness decreased with annealing treatment. The measured binding energy (BE) and branching ratio of the Sn 3d spin-orbital doublet were typical of oxidized states of Sn and the BE of the O1s core level of about 530~530.65eV also confirmed the presence of O-Sn bonds. The BE of oxygen and tin with annealing treatment shifted to higher position. O/Sn atomic ratios of films deposited at $375^{\circ}C$ for 2min and 4min were 1.99 and 2.01, respectively. The value of the atomic ratio O/Sn of films deposited at $375^{\circ}C$ for 2min changed from 1.99 to 2.45 with annealing treatment. Gas sensitivity depended on annealing temperature, the sensitivity increased with increasing annealing temperature.