• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.7
• /
• pp.95-102
• /
• 2016

Geomagnetic sensors are widely utilized for sensing heading direction of quadrotors. However, measurement from a geomagnetic sensor is easily corrupted by environmental magnetic field interference and roll/pitch directional motion. In this paper, a measurement method of a quadrotor heading direction is proposed for application to yaw attitude control. In order to eliminate roll/pitch directional motion effect, the geomagnetic sensor data is compensated using the roll/pitch angles measured for stabilization control. In addition, yaw-directional angular velocity data from a gyroscope sensor is fused with the geomagnetic sensor data using a complementary filter which is a simple and intuitive sensor fusion method. The proposed method is applied to experiments, and the results are presented to prove validity and effectiveness of the proposed method.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.4
• /
• pp.435-442
• /
• 2016

For inertial navigation systems, initial information such as position, velocity and attitude is required for navigation. Self-alignment is the process to determine initial attitude on stationary condition using inertial measurements such as accelerations and angular rates. The accuracy of self-alignment is determined by inertial sensor error. As soon as an inertial navigation system is powered on, the temperature of accelerometer rises rapidly until temperature stabilization. It causes acceleration error which is called temperature stabilizing error of accelerometer. Therefore, temperature stabilizing error degrades the alignment accuracy and also increases alignment time. This paper suggests a method to calculate azimuthal attitude using curve fitting of horizontal control angular rate in fixed-gain self-alignment. It is verified by simulation and experiment that the accuracy is improved and the alignment time is reduced using the proposed method under existence of the temperature stabilizing error.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.1
• /
• pp.47-60
• /
• 2018

In this paper, we proposed a method for eliminating aiming error of unguided anti-tank rocket using improved target tracking. Since predicted fire is necessary to hit moving targets with unguided rockets, a method was proposed to estimate the position and velocity of target using fire control system. However, such a method has a problem that the hit rate may be lowered due to the aiming error of the shooter. In order to solve this problem, we used an image-based target tracking method to correct error caused by the shooter. We also proposed a robust tracking method based on TLD(Tracking Learning Detection) considering characteristics of the FCS(Fire Control System) devices. To verify the performance of our proposed algorithm, we measured the target velocity using GPS and compared it with our estimation. It is proved that our method is robust to shooter's aiming error.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.2
• /
• pp.285-293
• /
• 2017

Jump rope has two motions. It starts as hand motion and ends as jump motion. Therefore, two motions should be considered together to detect rotations accurately. But previous researches only consider one of the two motions as in push-up, sit-up, lift dumbbells etc, which results in inaccurate detection of rotations. In this paper, detection of rotation in jump rope using two motions through 6-axis accelerometer gyro sensor is proposed. Jump motion is detected using accelerometer sensor and hand motion is detected using gyro sensor. Also start point and end point of jump rope is detected using magnitude and standard deviation of accelerometer and gyro sensor values. The count of rotation is detected using y-axis of gyro sensor value. Y-axis of gyro sensor value indicate hand motion of jump rope motion. The usefulness of the proposed method is confirmed through experimental results.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.72-75
• /
• 2004

In this paper, a finger-click recognition method is proposed to improve the recognition performance for finger-clicking of a wearable input device, called $SCURRY^{TM}$. The proposed method is composed of three parts including feature extraction part, valid click discrimination part, and cross-talk avoidance part. Two types of MEMS inertial sensors are embedded into the wearable input device to measure the angular velocity of a hand (hand movement) and the acceleration rates at the ends of fingers (finger-click motion). The experiment applied to the $SCURRY^{TM}$ device shows the improved stability and performance.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2016.07a
• /
• pp.117-118
• /
• 2016

줄넘기는 줄을 돌리는 손동작과 뛰어오르는 동작이 결합된 운동으로 정확한 카운트를 위해서는 두 동작을 함께 고려해야 한다. 이전의 연구들에서는 단순 반복적인 운동인 윗몸일으키기, 팔굽혀펴기, 아령 운동과 함께 치부하여 하나의 동작만을 체크하여 카운트 하였다. 이것은 실제 줄넘기 동작과는 차이가 있으며 두 동작 중 하나의 동작만을 하고 있다면 확인해내지 못하는 문제가 있다. 본 논문에서는 6축 가속도 자이로 센서를 이용하여 두 동작을 모두 확인하고 카운트하는 방법을 제안한다. 가속도 센서를 이용하여 뛰어오르는 동작을 확인하며 자이로 센서를 이용하여 손동작을 확인한다. 이때 확인되는 값의 파형을 이용하여 줄넘기 횟수를 카운트하게 된다. 제안하는 방법은 실제 실험을 통하여 카운트 방법의 성능을 확인할 수 있다.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.9
• /
• pp.723-732
• /
• 2016

This paper proposes an approach to fused navigation of an unmanned surface vehicle(USV) and to detection of the outlier or interference of global positioning system(GPS). The method fuses available sensor measurements through extended Kalman filter(EKF) to find the location and attitude of the USV. The method uses error covariance of EKF for detection of GPS outlier or interference. When outlier or interference of the GPS is detected, the method excludes GPS data from navigation process. The measurements to be fused for the navigation are GPS, acceleration, angular rate, magnetic field, linear velocity, range and bearing to acoustic beacons. The method is tested through simulated data and measurement data produced through ground navigation. The results show that the method detects GPS outlier or interference as well as the GPS recovery, which frees navigation from the problem of GPS abnormality.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.474-474
• /
• 2000

This paper shows that a system with two-link arm can obtain hand reaching movement to a target object projected on a visual sensor by reinforcement learning using a layered neural network. The reinforcement signal, which is an only signal from the environment, is given to the system only when the hand reaches the target object. The neural network computes two joint torques from visual sensory signals, joint angles, and joint angular velocities considering the urn dynamics. It is known that the trajectory of the voluntary movement o( human hand reaching is almost straight, and the hand velocity changes like bell-shape. Although there are some exceptions, the properties of the trajectories obtained by the reinforcement learning are somewhat similar to the experimental result of the human hand reaching movement.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.1067-1072
• /
• 1996

Sensitivity analysis of the cylindrical zigzag cams under acceleration and centrifugal forces is performed. A Lagrangian method is used to determine the mechanism constant of zigzag track, And the equation of motion for cylindrical zigzag cam under rectangular pulse is derived by the governing equations of a single spring mass system. The ratio of the drive force tn resisting force is derived by angular acceleration, centrifugal force and setback force on the operation of the munition. The theoretical sensitivity curves for 3 models are analyzed. And experiments for 3 models are conducted to check safe and functional zone. Zigzag cam types can be satisfied all major design requirements for switch system of munition.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2076-2078
• /
• 2002

This paper presents an Intelligent Balance Beam Controller(IBBC) which can estimate the inertia of load automatically. Balance Beam controller is a kind of construction tool which can control the attitude of the load hanging in the air such as a beam carried by crane. In our previous work, Balance Beam had been built to control the object in air using a mechanical gyro system having a position controllable gimbal structure. In field application the load inertia for operation is not easy to figure out because the weight and shape which determines the inertia, varies depending on the object to be carried. Therefore it is difficult for a worker to operate a Balance Beam and an accident could be caused occasionally. We designed an automatic load estimator to measure the inertia of arbitrary load by using an angular velocity sensor that is installed on the Balance Beam. Simulation results and current status for implementation are presented.