• 한국항공우주학회지
• /
• 제36권5호
• /
• pp.420-427
• /
• 2008

접힌 공력면이 전개하는 운동을 모사하기 위하여 전개 운동 방정식을 수립하고 공력면에 작용하는 모멘트 등을 모델링하였다. 공력에 의한 롤 모멘트는 정적 롤 모멘트와 감쇠 모멘트로 이루어져 있으며 정적 롤 모멘트는 전개 하중 측정을 위한 풍동 시험을 통하여 획득한 정적 롤 모멘트 계수로부터 계산된다. 롤 감쇠 계수는 패널법을 이용한 수치 해석을 통하여 산출되었는데 전개 각속도로부터 유발된 받음각에 상응하는 변위각을 공력면에 적용하여 수치해석을 하였다. 공력면 형상에 적용한 변위각은 회전 중심으로부터 공력면 끝단까지 선형적으로 증가하며 회전 중심에서는 변위가 없다. 롤 감쇠 계수는 전개 각속도에 따른 롤 모멘트 계수의 변화율로 계산되며 공력조건과 전개각의 함수이고 전개 각속도에 대해서는 일정하다고 가정하였다. 롤 감쇠를 포함하여 모사된 공력면의 전개 모사는 시험과 비교하여 유사한 결과를 보여주었다.

• 한국항공우주학회지
• /
• 제33권10호
• /
• pp.60-67
• /
• 2005

현대의 고성능 전투기는 한계받음각 내에서 적절한 조종성(Controllability) 및 안정성(Stability)을 확보하고 있어야 한다. 고받음각에서 항공기가 이탈에 진입할 수 있는 한계값은 항공기 형상설계에 직결되는 문제이다. 하지만 현대의 고성능 전투기는 전기식 비행제어계통(Digital Fly-By-Wire Flight Control System)을 사용하여 고받음각 제어법칙을 설계함으로써 한계값 내에서 항공기의 안정성을 보장하고 있다. 현재, T-50 세로축 고받음각 제어법칙에는 (+)한계받음각 이상으로의 비행을 제한하는 받음각 제한기(Angle of Attack Limiter)가 설계되어 있다. 그러나 (-)한계받음각 이상으로 비행을 제한하는 받음각 제한기는 설계되어 있지 않아, 조종사의 과도한 (-)세로축 기동에 대해 항공기가 이탈에 진입할 수 있다. 그리고 T-50 비행시험에서 PA에서 과도한 (+)세로축 기동 시, 받음각(Angle of Attack)이 현재 설계되어 있는 한계받음각을 초과하는 문제점이 발생하였다. 본 논문에서는 고받음각 제어법칙을 일부 수정하여 한계받음각 내에서 항공기의 세로축 조종성능을 향상시키고, 항공기 안정성을 확보할 수 있는 제어법칙에 관한 연구를 수행하였다.

• 한국항공운항학회지
• /
• 제4권1호
• /
• pp.87-99
• /
• 1996

• 한국태양에너지학회 논문집
• /
• 제22권4호
• /
• pp.77-84
• /
• 2002

In order to investigate forced convection heat transfer due to the wind from the inner surface of a cavity receiver for a parabolic dish type solar energy collecting system, a two-dimensional rectangular cavity receiver is prepared and installed in a wind tunnel. The convection heat transfer coefficient of the inner surface of the receiver is dependent on the direction and the velocity of the wind. The attack angle of the cavity and the air velocity in the tunnel are controlled in a wide range so that the effects of the attack angle and the wind velocity on the heat transfer coefficient can be studied. The skirt is installed at the aperture of the cavity in order to reduce convective heat loss. The effects of the length and the installation angle of the skirt on convection heat transfer of the cavity are tested. It is found that convection heat loss can be significantly reduced by installing the skirt. Also, it is known that heat transfer from the cavity can be minimized if the angle of the skirt is $90^{\circ}$ to the outer surface of the cavity.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.357-364
• /
• 2004

A computational study on the supersonic flow around the lateral jet controlled missile has been performed. Case studies have been performed by comparing the normal force coefficient and the moment coefficient of a missile body for several different jet flow conditions, angle of attacks, circumferential jet locations, and spouting jet angles. For the several different jet flow conditions, which include the jet pressure, the jet Mach number, and the corresponding jet mass flow rate, the results show that the normal force coefficient is almost proportional to the jet thrust but the moment coefficient is not. Distinctly different flow phenomena can be noticed as the pressure ratio and the jet Mach number increase. By investigating the angle of attack effect to the normal force and the pitching moment, it has been identified that the normal force and the pitching moment show nonlinearity with respect to the angle of attack. From the detailed flow field analyses with respect to the jet flow conditions and the angle of attacks, it is verified that most of the normal force loss and the pitching moment generation are taken place at the low-pressure region behind the jet nozzle. Furthermore, the normal force and the pitching moment characteristics of the missile have been identified by comparing different circumferential jet locations and spouting jet angles.

• 대한조선학회논문집
• /
• 제56권6호
• /
• pp.541-549
• /
• 2019

In the present study, we investigated planing forces of supercavitated bodies by using the supercavitation shape produced by the disk type cavitator. The cavity shapes are observed to find the immersion draft and planing angle when the stern of the supercavitated body is partially immersed in the water. To make the planing the angle-of-attack (AOA) of the supercavitated body is varied statically against the main flow and the planing tests are carried out for different body shapes that are changed systematically. The drag, lift and pitch moment acting on the body are measured to understand the relation between the planing force and the immersion draft of the supercavitated body. It is found that the planing force increased in general linearly with the immersion draft ratio and the planing angle is certainly not proportional to the immersion draft ratio.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.759-764
• /
• 2003

Numerical simulations are conducted to investigate the mechanism of hovering flight by single flapping wing, and to examine the effect of the phase difference between the fore- and hindwings in hovering flight by two flapping wings. The numerical method used is based on an immersed boundary method in Cartesian coordinates. The Reynolds number considered is Re=150 based on the maximum translational velocity and chord length of the wing. For single flapping wing, the stroke plane angles are $0^{\circ}$, $30^{\circ}$, $60^{\circ}$, $75^{\circ}$ and $90^{\circ}$ and the downstroke angles of attack are varied for each stroke angle. Results show that for each stroke plane angle, there is an optimal angle of attack to maximize the vertical force. Below the stroke angle of $60^{\circ}$, wake capturing reduces the negative vertical force during the upstroke. For two flapping wings, The phase lags of the hindwing are $0^{\circ}$, $90^{\circ}$, $180^{\circ}$ and $270^{\circ}$. The amplitudes of the stroke are 2.5 and 4.0 times the chord length at each phase lag. The results show that maximum vertical force is generated when the phase lag is zero, and the amplitude of the vertical force is minimum at the phase lag of $180^{\circ}$.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국제학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.1659-1663
• /
• 1991

A new control design methodology is presented here which is based on a nonlinear time-series reference model. It is indicated by highly nonlinear simulations that such designs successfully stabilize troublesome aircraft maneuvers undergoing large changes in angle of attack as well as large electric power transients due to line faults. In both applications, the nonlinear controller was significantly better than the corresponding linear adaptive controller. For the electric power network, a flexible a.c. transmission system (FACTS) with series capacitor power feedback control is studied. A bilinear auto-regressive moving average (BARMA) reference model is identified from system data and the feedback control manipulated according to a desired reference state. The control is optimized according to a predictive one-step quadratic performance index (J). A similar algorithm is derived for control of rapid changes in aircraft angle of attack over a normally unstable flight regime. In the latter case, however, a generalization of a bilinear time-series model reference includes quadratic and cubic terms in angle of attack. These applications are typical of the numerous plants for which nonlinear adaptive control has the potential to provide significant performance improvements. For aircraft control, significant maneuverability gains can provide safer transportation under large windshear disturbances as well as tactical advantages. For FACTS, there is the potential for significant increase in admissible electric power transmission over available transmission lines along with energy conservation. Electric power systems are inherently nonlinear for significant transient variations from synchronism such as may result for large fault disturbances. In such cases, traditional linear controllers may not stabilize the swing (in rotor angle) without inefficient energy wasting strategies to shed loads, etc. Fortunately, the advent of power electronics (e.g., high-speed thyristors) admits the possibility of adaptive control by means of FACTS. Line admittance manipulation seems to be an effective means to achieve stabilization and high efficiency for such FACTS. This results in parametric (or multiplicative) control of a highly nonlinear plant.

• 한국항해항만학회지
• /
• 제32권10호
• /
• pp.771-776
• /
• 2008

선박에서 제어판의 역할은 운동을 제어하는데 목적이 있으며 이는 곧 조종성능을 결정하는 중요한 요소이다. 본 연구에서는 플랩타의 성능평가를 위하여 $Re=3.0{\times}10^4$에서 영각에 대응하는 플랩각에 따른 속도 및 에너지 분포를 2-프레임 그레이레벨 상호상관 PIV기법을 이용하여 비교 분석하였다. 또한 영각 10도와 20도에서 전통적인 단동타의 유동특성과 비교하여 플랩타의 성능특성을 평가하였다. 영각 10도에서는 양력, 영각 20도에서는 항력에 의한 측압력을 향상시킬 수 있었다. 영각 10도에서 플랩조작만으로 박리점과 경계층영역의 변화가 가능하였다.

• 한국항공우주학회지
• /
• 제34권10호
• /
• pp.61-70
• /
• 2006

마하 4 비행 조건에서 작동하는 고성능 램제트와 듀얼모드 스크램제트 엔진의 초음속 공기 흡입구 모델을 설계하였다. 배압, 받음각, 요각 등 비행 변수의 변화에 따른 내부 유동 특성을 파악하기 위하여 규슈대학교의 불어내기식 초음속 풍동을 이용한 실험을 수행하였다. 유동 가시화를 위하여 쉴리렌 기법, 오일 가시화 기법을 이용하였으며, 정량적 성능 분석을 위하여 표면 압력 및 전압력을 측정하였다. 실험의 결과는 전산 유체 해석과 비교하였다. 본 연구는 기본적이지만 찾기 힘든 고 마하수 초음속 공기 흡입구 유동의 실험 결과를 제시한다.