• 대한기계학회논문집A
• /
• 제24권11호
• /
• pp.2680-2687
• /
• 2000

The Reynolds equation, incorporating Elrods cavitation algorithm, is discretized on a rectangular grid in computational space through coordinate mapping in order to accurately analyze a herringbone grooved journal bearing of a spindle motor in a computer hard disk drive. The pressure distribution and cavitation area are determined by using the finite volume method. Predicted results are compared to experimental data of previous researchers. It was found that positive pressure is developed within the converging section of the bearing and that a cavity occurs in the diverging section. Cavitation has been neglected in the previous analysis of the herringbone grooved bearing. Load capacity and bearing torque are increased due to the increased of eccentricity and L/D and the decrease of the grooved width ratio. The maximum load capacity was found to occur at a groove angle of 30 degrees while bearing torque remains constant due to the variation of the groove angle. The cavitation region is significantly decreased with the inclusion of herringbone grooves. However, the region increases with the increase of the eccentricity, L/D, groove angle and the rotational speed and the decrease of the grooved width ratio.

• 소성∙가공
• /
• 제30권3호
• /
• pp.125-133
• /
• 2021

In this study, response surface method (RSM), back propagation neural network (BPNN), and genetic algorithm (GA) were used for modeling and multi-objective optimization of the parameters of AA5052-H32 in incremental sheet forming (ISF). The goal of optimization is to determine the maximum forming angle and minimum surface roughness, while varying the production process parameters, such as tool diameter, tool spindle speed, step depth, and tool feed rate. A Box-Behnken experimental design (BBD) was used to develop an RSM model and BPNN model to model the variations in the forming angle and surface roughness based on variations in process parameters. Subsequently, the RSM model was used as the fitness function for multi-objective optimization of the ISF process the GA. The results showed that RSM and BPNN can be effectively used to control the forming angle and surface roughness. The optimized Pareto front produced by the GA can be utilized as a rational design guide for practical applications of AA5052 in the ISF process

• 치과방사선
• /
• 제29권1호
• /
• pp.357-365
• /
• 1999

Desmoplastic fibroma is a rare. benign intraosseous fibroblastic tumor. which is locally aggressive. It is osseous counterpart of soft tissue fibromatosis. The authors experienced the patient who complained persistent mouth opening limitation with mild swelling on the left mandibular angle area. After careful analysis of clinical. radiological and histopathological findings. we diagnosed as desmoplastic fibroma of the mandible. The results were as follows: 1. Main clinical symptoms were mouth opening limitation which had been persistent for 9 months and mild swelling on the left mandibular angle area. 2. Radiographs showed the radiolucent lesion and expansion of lingual cortex. CT finding is homogeneous soft tissue mass with expansion of left mandibular ramus. Destruction of medial wall of ramus and invasion to adjacent soft tissue is also seen. 3. Histopathologically, plump spindle shaped fibroblasts arranged in bundles or fascicles are observed. The cells of tumor are infiltrating into muscle fiber with destruction of bony trabeculae and merged with surrounding salivary gland.

• 한국정밀공학회지
• /
• 제19권2호
• /
• pp.133-139
• /
• 2002

A number of experimental studies on burr formation in face milling operations have been pursued. They usually focus on machining parameters such as depth of cut, leed rate, spindle speed and in-plane exit angle. But it if difficult to set the correlation between burrs and the parameters on burr when such parameters are considered at the same time. Therefore, in this paper, acoustic emission (AE) is considered as an alternate way to predict burr types regardless of machining conditions. AE signals during face milling were sampled and processed, then fed into an artificial neural network to classify burr types \\\"on-line\\\".\\\".uot;.

• 한국공작기계학회논문집
• /
• 제11권2호
• /
• pp.1-8
• /
• 2002

Cutting force is obtained as a sum of chip removing force and ploughing force. Chip removing force is estimated by multiplying specific cutting pressure by cutting area. Since ploughing force is caused from dullness of a tool, its magnitude is constant if depth of cut is bigger than a certain value. Using the linearity of chip removing force to cutting area and the constancy of ploughing force regardless of depth of cut which is over a certain limit each force is separated from measured cutting force and used to establish cutting force model. New rotation matrix to convert the measured cutting force in reference axes into the forces in cutter axes is obtained by considering that tool angles are projected angles from cutter axes to reference axes.. Spindle tilt is also considered far the model. The predicted cutting force estimated from the model is in good agreement with the measured force.

• 산업공학
• /
• 제10권1호
• /
• pp.223-235
• /
• 1997

The process of determining the optimal tool path in PCB(printed circuit board) drilling operations is identical with that of solving a TSP(traveling salesman problem). However, the optimal solution will be ruined when a drill bit needs tracking back in its tool paths. The back tracking occurrences shorten a life of the main spindle and result in inaccurate mechanical movements. In this study, the performances of four heuristics(Nearest Neighbor, Convex Hull, Greatest Angle and Most Eccentric Ellipse) are evaluated to obtain feasible tool paths along with less number of back trackings for a large number of holes(more than 2000holes/bit) and to generate corresponding NC codes for a given CNC drill. Also, the operations of these algorithms are visualized to show a user the graphic image of tool visitation with PCB holes on a computer screen.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.102-106
• /
• 1996

In the ball end-milling process of a 3-dimensional mold, it is important to select cutting conditions and tool path considering the geometrical shape of a workpiece to reduce machining time. In this study, experiments were performed to decide allowable feed rate not breaking stability of system for different geometrical shapes. It was found that downcut is more stable than upcutting in machining side wall and downward is preferable to upward in inclined part depending on the angle of the inclination and depth of cut.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.169-172
• /
• 2000

In this paper, an OMM (On-the-Machine Measuring) system has been developed, which can perform measuring and inspection of sculptured surfaces of die and mold, by use of a scanning-type touch probe mounted into the spindle of a NC machine. The calibration procedures of a scanning prove (SP2-1, Renishaw) and an algorithm for measuring surface points by a ball-nosed stylus have been studied. The system has been developed based on commercial CAM software (Z-Master 2000), and tested through measuring a plastic injection molding-die. Also some experimental results of the calibration and measuring for given surface positions are analyzed to verify its accuracy and reliability.

• 한국정밀공학회지
• /
• 제12권6호
• /
• pp.96-104
• /
• 1995

A study for a lathe to machine workpiece with noncircular cross-section is presented. The noncircular cutting is accomplished by controlling radial tool position synchronized with revolution angle of the spindle according to the desired cross-sectional shape. A learning control algorithm is suggested for the tool positioning. The learning law of the algorithm is based on pole-zero cancellation, which guarantees the control stability. The control performances are analyzed and simulated on a numerical computer that the effectiveness of the control algorithm is convinced. The algorithm is tested on a conventional NC-lathe which shows some successful results.

• 대한기계학회논문집A
• /
• 제41권3호
• /
• pp.181-186
• /
• 2017

점진 판재 성형은 금형을 제작하지 않고 판재를 가공하는 방법으로써 빠른 시제품 제작과 소량 생산에 적합한 성형법이다. 이러한 점진 판재 성형의 공정 변수로 공구 직경, 매 스탭당 z-방향 깊이, 공구 이송속도, 공구 회전 속도 등은 성형품의 품질에 크게 영향을 미친다. 본 연구에서는 Al5052-O(0.8mm) 판재를 사용하여 Varying Wall Angle Conical Frustum 모델의 점진성형을 실시하였으며, 각각의 변수들의 조합에서 성형성을 판단하였다. 다구찌 기법을 사용하여 점진성형 변수들의 조합을 찾아내고, 그레이 관계형 최적화를 통하여 최적 성형 변수 값의 조합을 찾아 내였다. 최종 성형물의 품질은 성형성, 스프링 백, 두께 감소량을 측정하여 판단하였다. 본 연구의 실험 조건에서의 최적의 변수 조합은 공구직경 6 mm, 회전속도 60rpm, 매 스탭당 z-방향 깊이 0.3 mm, 이송속도 500 mm/min으로 판단되었다.