• 한국자동차공학회논문집
• /
• 제18권6호
• /
• pp.7-13
• /
• 2010

In this study, we investigated the efficient FE modelling techniques for thermal stress analysis of the exhaust manifold subject to thermo-mechanical cyclic loadings. At first, full engine model was considered to identify the critical locations and their results were compared to failure site shown by the engine bench test. And the equivalent system model was proposed based on the mechanical behavior of the full engine model. The weak areas of both FE models show a good agreement with the experimental crack location. As a result, a simplified modelling methodology was verified to estimate the thermo-mechanical behaviors of the exhaust manifold under thermal shock test condition.

• Earthquakes and Structures
• /
• 제6권1호
• /
• pp.19-43
• /
• 2014

A risk assessment framework for evaluating building structures is implemented in this study. This framework allows considering sources of uncertainty both on structural capacity and seismic demand. In particular randomness on seismic load, incident angle, material properties, floor mass and structural damping are considered; in addition the choice of fibre modelling versus plastic hinge model is also considered as a source of uncertainty. The main objective of this work is to study the contribution of these sources of uncertainty on the fragilities of steel and steel-reinforced concrete composite 3D building structures. The fragility curves are expressed in the form of a two-parameter lognormal distribution where vertical statistics in conjunction with metaheuristic optimization are implemented for calculating the two parameters.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 A
• /
• pp.205-207
• /
• 2005

In this paper, the Point of Common Coupling (PCC) is selected to analyze harmonic characteristic of distribution system by IEC 61000 - 3 - 6 in Electromagnetic Compatibility(EMC). Harmonic voltage and current were measured at the PCC of real distribution system. Harmonic distribution, nonlinear load component and Total Harmonic Distortion(THD) were verified by measurement. The effective and accurate modelling of real distribution system were proved through a analysis of harmonic impedance, voltage and current in steady-state. Harmonic transfer characteristic in distribution system were summarized and investigated through a analysis of harmonic voltage and harmonic current in harmonic current source.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.478-481
• /
• 2006

Reinforced concrete shear wall is composed of wall, horizontal and vertical flanges. Due to the abrupt change in its geometry, it is difficult to predict the ultimate behaviour of shear wall in the action of lateral forces. For the better understanding of ultimate state, the propagation of crack and inelastic compressive zone are simulated reasonably. In this study, for the improvement of analysis result for shear wall with flanges, analyses are fulfilled with the application of some modelling methods including various material and geometrical models and numerical methods. The results from various modelling methods are compared and the advisable model is proposed.

• 한국전기전자재료학회논문지
• /
• 제30권7호
• /
• pp.459-462
• /
• 2017

In this study, we design, model, and analyze a compound generator that combines the axial flux permanent magnet (AFPM,) and radial flux permanent magnet (RFPM), which is expected to increase power generation by allowing the magnets to be placed on the upper, lower, left, and right sides of the same-sized generator. Through the design, modelling, and analysis of AFPM and RFPM compound generators, the generator load evaluation results rated output of 500.25 W and efficiency of 87.60%, respectively, at a rated speed of 600 rpm. By employing this complex generation system,these findings are expected to contribute to the activation of a small power generation system.

• 대한기계학회논문집
• /
• 제19권2호
• /
• pp.597-604
• /
• 1995

When a pipe bend is modelled with straight beam elements, its stiffness, particularly in bending behavior, is overestimated than its true value. In this paper, we propose a simple and practical beam-modelling technique to estimate its stiffness properly. When this technique, based on the strain energy concept, is employed to modify the beam sectional properties of the bend, quite satisfactory results can be obtained. To verify the validity of this method, we apply the present technique to the free vibration analysis of a center pipe with 2 bends, one of the three components of the automobile exhaust system.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권4호
• /
• pp.577-586
• /
• 2004

Structural failures, such as crack initiation, often arise near the bolted parts of the side member and trunnion bracket in some commercial vehicles. The purpose of this paper is: 1) establishment of a simple and practical bolted joint modelling technique and 2) determination of the key design variables for design improvement based on numerical experiments. Once the bolted joint modelling technique is established through experimental verification, the key design variables must be identified in order to alleviate the level of the stress concentration near the problem region. Numerical results indicate that the torsional rigidity of the frame cross-section should be increased to reduce the level of the maximum stress at the actual crack initiation location.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.213-219
• /
• 2000

In this work, it has been predicted the thermal performance of the engine cooling system in cases of stationary mode, constant speed mode, city-drive mode, and hill-climb mode by theoretical modeling of each component and numerical analysis. The modelling components are engine, radiator, heater, thermostat, water-pump, and cooling-fan. And also it has been developed the simulation program that can be used in case of design and system configuration changes. The comparison has not been made to verify the results of this work with experimental data, but the overall tendencies were agreed well with those of actual situation in four modes.

• 대한안전경영과학회지
• /
• 제5권2호
• /
• pp.75-85
• /
• 2003

Manufacturing firms have adapted seriously the Design for Manufacture and Assembly (DFMA) techniques which consider concurrently all factors related to the product development by using effective communications and sharing of information on product development processes. This study performed modelling and characterizing the data related to product manufacturing information for Design for Manufacture(DFM) evaluation and analysis. It adapted component-based development method for communicating and managing manufacturing information among distributed manufacturing organizations. Introducing component-based development offers safety and speed to network based system. This development using Unified Modelling Language(UML) provides efficient way for reconstruction and distribution of applications. Also, the integration of database and component into the internet environment enables to communicate and manage effectively manufacturing information for DFM evaluation and analysis at any place in the world. Therefore this system can make it more reasonable that evaluating, analyzing, and effective decision making of product design using DFM technique.

• ETRI Journal
• /
• 제5권3호
• /
• pp.9-15
• /
• 1983

본 연구에서는 MIL-HDBK-2l7D의 Part stress 해석방법을 이용하여 부품의 고장률을 계산하였다. 이 방법은 운용시 주위환경, 주위온도에 의한 stress등 많은 양의 자세한 정보가필요하다. 본고에서는 part stress 방법을 적용한 컴퓨터 프로그램을 개발하여 부품의 고장률 계산에 이용하였다. Fortran V로 쓰여진 이 프로그램은 다음의 4개 부분으로 구성되었고 그 기능및구조를 제시하였다. (1) Raw data file (2) 부품별 연산 프로그램 (3) 신뢰도 modelling (직렬구조) (4) New data file