• Journal of Welding and Joining
• /
• 제23권1호
• /
• pp.69-76
• /
• 2005

Recently, application of arc welding to galvanized carbon steel sheet is on the increasing Ould in the fields of automobile and construction industries. In arc welding process, zinc is evaporated in weld pool, even under the appropriate welding condition and produce blowhole and/or pit. Zinc gas cause instability of arc and increase spatter and fume. This research is purposed to minimize the heat-input and the formation of porosities in the welded joint of the galvanized carbon steel sheet using variable polarity AC wave pulse MIG welding system. An appropriate welding condition which showed low spatter and good bead appearance was acquired by applying the AC pulse MIG welding machine to DC duplicated MIG welding with the solid wire. When oxygen gas was added to shield gas of MIG welding for galvanized steel sheet, arc length was increased and arc stability was improved. In the AC duplicated welding, the loss of galvanized layer was decreased as the amount of heat-input was decreased when the EN ratio was increased under the condition that average welding current was evenly set.

• Journal of Welding and Joining
• /
• 제31권3호
• /
• pp.60-65
• /
• 2013

Ar, $N_2$, and He are the conventional kind of shield gas that are used for laser welding. Many researches on the impact of laser welding shield gas have been done, and it is on going until now. However, there are few studies that analyze the changes and differences of the plasma emission signal. Therefore, in this study, we evaluated the change in the penetration characteristics according to the type of shield gas during fiber laser welding impacts to the plasma signal. As a result, if was checked that the difference in molecular weight of Ar, $N_2$, and He affects to the amount of spatter, and also found that the measured plasma radiation signal changes similar to the order of the molecular weight of the gases. Especially, clear change on the signal intensity per each shield gas was measured through RMS, and found that the shield gas was nothing to do with the FFT analyzed result.

• Journal of Welding and Joining
• /
• 제32권6호
• /
• pp.35-40
• /
• 2014

The contact tip for gas metal arc welding has important functions to transmit the welding current to the wire and to guide the wire to molten pool. If the contact tip is damaged, it is a cause of lowering the welding productivity due to removal of welding defects and replacement of contact tip. In case of the use of a contact tip for a long time the arc is unstable because the processed hole in the contact tip center is larger, and the variation of aiming position of the welding wire causes a seam tracking error. In this study, gas metal arc welding experiments using contact tip of three different materials were performed. The contact tips with Cu-P, Cu-Cr, and Cu-ODS were used at the experiments, and the welding characteristics by each contact tip were evaluated. After welding contact tip appearance, welding spatter adhesion amount of the nozzle, and weld bead appearance were evaluated. The welding current and welding voltage were measured to verify arc stability during arc welding.

• Journal of Welding and Joining
• /
• 제25권3호
• /
• pp.18-27
• /
• 2007

Laser welding process is widely used in the industrial field due to its numerous advantages: a small heat affected zone(HAZ), deep penetration, high welding speed, ease of automation, single-pass thick section capability, enhanced design flexibility, and small distortion after welding. The objective of this research works is to investigate the influence of the process parameters, such as the welding fur metals with CW Nd:YAG lasers. The bead-on-plate and Lap welding experiments are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the welding quality of the cross section, tensile stress behavior and the hardness of the welded part are investigated in comparison of the Nickel coated and Nickel uncoated S45C steel. As a result of experiment, nickel coated S45C Steel showed more even weld zone than Nickel uncoated counterpart upon lap welding. Also, it showed relatively small amount of internal defects and spatter, and Nickel coated S45C showed better weldability than Nickel uncoated S45C steel. The optimum welding process upon lap welding of Nickel coated S45C steel is when each laser power is 1900W; focal positions is -1mm; welding speed is $0.9{\sim}1.0m/min$. The heat input was $4.178{\sim}4.36{\times}103J/cm^2$.

• 한국응용과학기술학회지
• /
• 제30권1호
• /
• pp.71-77
• /
• 2013

알루미늄 테르밋 반응의 환원제로서 알루미늄 분말은 200 메쉬 이하의 미분이 필요하나, 알루미늄의 높은 인성과 분말 제조비 때문에 경제적으로 용이하지 않다. 그러므로 $Mn_3O_4$ 분진 환원용 알루미늄 미분의 제조 코스트를 낮추기 위해, 알루미늄 합금분말의 제특성이 검토되었다. 망간을 다량 함유한 알루미늄 합금괴는 취성이 큰 금속간 화합물을 함유하고 있기 때문에 쉽게 파쇄할 수 있다. 또 망간은 망간 합금철의 주성분이다. Al-15%Mn 합금분말을 기계적 파쇄법으로 저렴하게 제조할 수 있다. Al 분말 대신에 Al-15%Mn 합금분말을 사용한 테르밋 반응 결과는 환원제로 순 알루미늄 분말을 사용한 경우와 같이 고순도 망간 합금철을 얻을 수 있었다. Al-15%Mn 합금분말를 이용한 $Mn_3O_4$ 분진의 망간 회수율은 알루미늄 분말을 이용한 경우의 약 65% 보다 높은 약 70%의 높은 수준을 보였으며, 이는 비산이 적은 것에 기인한다.

• 한국산학기술학회논문지
• /
• 제20권8호
• /
• pp.133-138
• /
• 2019

본 논문은 자동차 구조용 열간 압연 강재인 SAPH440을 GMAW 겹치기 용접을 하여 용접 변수인 용접 전류, 용접 전압, 이송 속도를 달리하여 인장 특성을 평가하였다. GMAW 공정의 접합 변수에 따라 인장 시험을 수행하기 위하여 겹치기 용접 하여 KS B ISO 9018에 따라 시험편을 제작하여 실험하였다. 각 조건에 따른 비드 외관을 관찰하였고 그에 따른 인장시험을 하여 용접성을 평가하였다. 평가 결과 용접전류가 높을수록 깊은 용입이 형성되는 것을 알 수 있었으나 인장강도 측면에서는 모재부 파단으로 인해 일정 변수 이상부터는 큰 차이는 없는 것으로 확인되었다. 용접 전류 200A, 용접 전압 17V의 조건에서와 같이 전압에 비해 전류가 높으면 다량의 스패터가 발생하며 용접이 불안정하고 이로 인해 용접부 파단이 일어나는 것을 확인 하였다. 전압이 높을수록 대체로 결함이 발생 되지 않을 정도의 비드외관을 관찰할 수 있었으며 너무 높은 전압 또한 용접성에 영향을 끼치는 것을 확인하였다. 너무 낮은 전류와 전압의 조건에서는 용접이 정상적으로 되지 않아 인장강도를 측정할 수 없었다. 그러나 용접이 가능한 용접 조건에서는 전류가 증가함에 따라 전압과 이송속도가 증가하더라도 인장강도에는 큰 영향을 미치지 않았다.