• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.380-381
• /
• 2007

This paper reports on the deposition conditions and properties of ITO films used as electrode layer in a organic light emitting diodes on a PET substrate. The deposition technique employed was specially designed roll-to-roll sputtering. The oxide was deposited at room temperature in an argon and oxygen plasma on a transparent conducting ITO layer on a PET film. The influence of deposition parameters such as DC power, working pressure and oxygen partial pressure has been investigated, in order to obtain the best compromise between a high deposition rate and adequate electro-optical properties. Electrical and optical properties of ITO films were analyzed by Hall measurement examinations with van der pauw geometry at room temperature and UV/Vis spectrometer analysis, respectively. In addition, the structural properties and surface smoothness were measured by x-ray diffraction and scaning electron microscopy, respectively. From optimized ITO films grown by roll-to-roll sputter system, good electrical$(6.44{\times}10^{-4}\;{\Omega}-cm)$ and optical(above 86 % at 550 nm) properties were obtained. Also, the ITO films exhibited amorphous structure and very flat surface beacause of low deposition temperature.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.133-133
• /
• 2009

DC 마그네트론 스퍼터링법을 이용하여 투명 폴리이미드 기판위에 $CeO_2$가 0.5, 3.0, 4.0, 6.0wt% 도핑된 고밀도 ITO 타켓으로 증착된 ITO:Ce 박막의 구조적, 기계적 특성, 전기적 특성을 연구하여싸. ITO 박막 내에 Ce 함량이 증가할수록 결정성이 감소하였으며 $CeO_2$가 3.0wt% 도핑된 ITO타켓으로 증착한 박막의 경우 비정질구조로서 $3.96{\times}10^{-4}{\Omega}cm$의 가장 낮은 비저항 값을 관찰할 수 있었고, 기계적 내구성 또한 가장 우수하였다.

• Journal of information and communication convergence engineering
• /
• v.3 no.4
• /
• pp.179-183
• /
• 2005

A photodiode capable of obtaining a sufficient photo/ dark current ratio at both forward bias state and reverse bias state is proposed. The photodiode includes a glass substrate, an aluminum film formed as a lower electrode over the glass substrate, an alumina film formed as an insulator barrier over the aluminum film, a hydrogenated amorphous silicon film formed as a photo conduction layer over a portion of the alumina film, and a transparent conduction film formed as an upper electrode over the hydro-generated amorphous silicon film. A good quality alumina $(Al_2O_3)$ film is formed by oxidation of aluminum film using electrolyte solution of succinic acid. Alumina is used as a potential barrier between amorphous silicon and aluminum. It controls dark-current restriction. In case of photodiodes made by changing the formation condition of alumina, we can obtain a stable dark current $(\~10^{-12}A)$ in alumina thickness below $1000{\AA}$. At the reverse bias state of the negative voltage in ITO (Indium Tin Oxide), the photo current has substantially constant value of $5{\times}10^{-9}$ A at light scan of 100 1x. On the other hand, the photo/dark current ratios become higher at smaller thicknesses of the alumina film. Therefore, the alumina film is used as a thin insulator barrier, which is distinct from the conventional concept of forming the insulator barrier layer near the transparent conduction film. Also, the structure with the insulator thin barrier layer formed near the lower electrode, opposed to the ITO film, solves the interface problem of the ITO film because it provides an improved photo current/dark current ratio.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.3
• /
• pp.128-132
• /
• 2009

Transparent conducting thin films of indium tin oxide(ITO) co-sputtered with aluminum-doped zinc oxide(AZO) were deposited on glass substrate by dual magnetron sputtering. It was found that the electrical properties and structural characteristics of the films are significantly changed according to the sputtering power of the AZO target. The IAZTO film prepared with D.C power of ITO at 100 W and R.F power of AZO at 50 W shows an electrical resistivity of $4.6{\times}10^{-4}{\Omega}{\cdot}cm$ and a sheet resistance of $30{\Omega}/{\square}$ (for 150 nm thick). Besides of the improvement of the electrical properties, compared to the ITO films deposited at the same process conditions, the IAZTO films have very smooth surface, which is due to the amorphous nature of the films. However, the electrical conductivity of the IAZTO films was found to be deteriorated along with the crystallization in case of the high temperature deposition (above $310^{\circ}C$). In this work, high quality amorphous transparent conductive oxide layers could be obtained by mixing AZO with ITO, indicating possible use of IAZTO films as the transparent electrodes in OLED and flexible display devices.

• Journal of the Korean Ceramic Society
• /
• v.43 no.3 s.286
• /
• pp.185-192
• /
• 2006

The effects of annealing on structural and electrical properties of ITO/PES (Indium Tin Oxide/Polyethersulfone) films was investigated. Amorphous ITO thin films were grown on plastic substrates, PES using low temperature DC magnetron sputtering. Various post annealing techniques were attempted to research variations of microstructure and electrical properties: i) conventional thermal annealing, ii) excimer laser annealing, iii) UV irradiation. The electrical properties were obtained using Hall effect measurements and DC 4-point resistance measurement. The microstructural features were characterized by FESEM, XRD, Raman spectroscopy in terms of morphology and crystallinity. Optimized UV treatment exhibits the enhanced conductivity and crystallinity, compared to those of conventional thermal annealing.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.189-189
• /
• 2009

다양한 증착 조건에서 마그네트론 2원 동시 방전법을 이용하여 유리기판위에 ITO (10wt% $SnO_2$ 타겟과 $Yb_{2}O_{3}$ 타겟을 사용하여 증착한 ITO:Yb 박막의 구조적, 전기적 특성을 연구하였다. 스퍼터 가스로서는 Ar 가스를 사용하였고, RF power가 0W이고 어닐링온도가 $200^{\circ}C$일 때, 가장 낮은 비저항 $2.442{\times}10^{-4}{\Omega}cm$을 나타내었다. ITO:Yb 박막의 전기적 특성은 Hall 효과 측정장비, 박막의 결정구조는 X-선 회절(XRD), 광학적 특성은 UV 측정장비를 사용하여 측정하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.08a
• /
• pp.89-92
• /
• 2003

ITO thin films were deposited by RF-magnetron sputtering method and crystallization behavior of the films with and without external heating as a function of deposition time was examined. X-ray diffraction results indicated an amorphous state of the film when the deposition time is short about 10 min. When the deposition time was increased over 20 min development of crystallization of the films is observed. Because RF-sputtering transfers the high-energy to the growing film by energetic bombardment, it is believed that considerable activation energy for the crystallization of the film has transferred during deposition, which resulted in the crystallization of ITO thin films without external energy supply.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.56-56
• /
• 2018

Transparent conductive oxides (TCOs) have attracted attention due to their high electrical conductivity and optical transparency in the visible region. Consequently, TCOs have been widely used as electrode materials in various electronic devices such as flat panel displays and solar cells. Previous studies on TCOs focused on their electrical and optical performances; there have been numerous attempts to improve these properties, such as chemical doping and crystallinity enhancement. Recently, due to rapidly increasing demand for flexible electronics, the academic interest in the mechanical stability of materials has come to the fore as a major issue. In particular, long-term stability under bending is a crucial requirement for flexible electrodes; however, research on this feature is still in the nascent stage. Hydrogen-incorporated amorphous In-Sn-O (a-ITO) thin films were fabricated by introducing hydrogen gas during deposition. The hydrogen concentration in the film was determined by secondary ion mass spectrometry and was found to vary from $4.7{\times}10^{20}$ to $8.1{\times}10^{20}cm^{-3}$ with increasing $H_2$ flow rate. The mechanical stability of the a-ITO thin films dramatically improved because of hydrogen incorporation, without any observable degradation in their electrical or optical properties. With increasing hydrogen concentration, the compressive residual stress gradually decreased and the subgap absorption at around 3.1 eV was suppressed. Considering that the residual stress and subgap absorption mainly originated from defects, hydrogen may be a promising candidate for defect passivation in flexible electronics.

• Solar Energy
• /
• v.8 no.1
• /
• pp.68-73
• /
• 1988

In the glass/TCO/p-i-n a-Si/Al type of amorphous silicon solar cell, the effects on solar cell efficiency and metastability for the various kinds of TCO analyzed by SAM and ESCA, which was used to measure the diffusion profiles of In and Sn and the Fermi energy shifts in the TCO/p interface respectively. Indium which diffused into a-Si p-layer did not have any significant effects on the Fermi level shift of p-layer when the content of $B_2H_6/SiH_4$ in p-layer was at 1 gas%. The cell fabricated on $SnO_2$ turned out to have the best cell photovoltaic characteristics. ITO fabricated by electron beam deposition system, which was shown to have the greatest rate of diffusion of Indium in ITO/p interface produced the worst metastability among the cells tested.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.295-295
• /
• 2016

Recently, TCO films with low carrier concentration, high mobility and high work function are proposed beneficial as front electrode in HIT solar cell due to free-carrier absorption in NIR wavelength region and low Schottky barrier height in the front TCO/a-Si:H(p) interface. We report high transmittance and work function zirconium-doped indium tin oxide (ITO:Zr) films with various plasma (Ar/O2 and Ar) conditions. The role of (Ar/O2) plasma was to enhance the work function of the ITO:Zr films whereas the pure Ar plasma based ITO:Zr showed good electrical properties. The RF magnetron sputtered ITO:Zr films with low resistivity and high transmittance were employed as front electrode in HIT solar cells, yield the best performance of 18.15% with an open-circuit voltage of 710 eV and current density of 34.63 mA/cm2. The high work function ITO:Zr films can be used to modify the front barrier height of HIT solar cell.