• Membrane and Water Treatment
• /
• v.7 no.1
• /
• pp.39-53
• /
• 2016

In this study, polysufone (PSf) was used as a base polymer to synthesize sulfonated polysulfone (SPSf) and aminated polysulfone (APSf) as cation and anion exchange polymers, respectively. Then the ion exchange polymers were coated onto the surface of commercial carbon electrodes. To compare the capacitive deionization (CDI) and membrane capacitive deionization (MCDI) processes, the pristine carbon electrodes and ionic polymer coated electrodes were tested under various operating conditions such as feed flow rate, adsorption time at fixed desorption time, and feed concentration, etc., in terms of effluent concentration and salt removal efficiency. The MCDI was confirmed to be superior to the CDI process. The performance of MCDI was 2-3 times higher than that of CDI. In particular, the reverse desorption potential was a lot better than zero potential. Typically, the salt removal efficiency 100% for 100 mg/L NaCl was obtained for MCDI at feed flow rate of 15 ml/min and adsorption/desorption time of 3 min/1 min and applied voltages 1.0 V for adsorption and -0.3 V for desorption process, and for 500 mg/L, the salt removal efficiency 91% was observed.

• Membrane Journal
• /
• v.25 no.5
• /
• pp.447-455
• /
• 2015

In this study, Polysulfone (PSf) and polyetherimide (PEI) as the anion exchange polymers were aminated in the different ratio whereas the polyether ether ketone (PEEK) as the cation exchange polymer was sulfonated. The bipolar membranes of SPEEK (sulfonated PEEK)/APSf (aminated PSf) and SPEEK/APEI (aminated PEI) were prepared by the double-casting method. The surfaces of bipolar membranes were fluorinated in accordance with the amination ratio and applied to produce the hypochlorite. As the amination increased, the hypochlorite concentration is also increased. Typically, for SPEEK/APSf 3 : 1 membrane, the produced hypochlorite concentration was 61.0 ppm and its durability was 220 min for the non-fluorinated membrane while for the fluorinated membrane, the concentration of 58.6 ppm and its durability lasted 570 min. Also for SPEEK/APEI 3 : 1 membrane, the hypochlorite concentrations of 60.1 ppm and 58.3 ppm for before- and after-fluorination, respectively were observed whereas the durability was remarkably developed from 150 min to 440 min. Therefore, the surface fluorination takes an important role for the development of the membrane durability.

• Membrane Journal
• /
• v.6 no.2
• /
• pp.72-78
• /
• 1996

This paper was to investigate the preparation of quaternary ammonium polysulfone. The aminated polysullone (AMPS) as quaternary ammonium polysulfone was synthesized by two-step process. The first step involves the preparation of chloromethylated polysulfone (CMPS) which was produced by the introducion of chloromethyl group into polysulfone using chloromethyl methyl ether as a chloromethylation agent and zinc oxide as a catalyst. The second step, amination of CMPS was to give rise to AMPS using triethylamine.

• Membrane and Water Treatment
• /
• v.6 no.1
• /
• pp.27-42
• /
• 2015

In this study, poly (phenylene oxide) (PPO) and poysulfone (PSf) were sulfonated and aminated respectively. Both sulfonated poly (phenylene oxide) (SPPO) and aminated polysulfone (APSf) were characterized via the measurement of FT-IR, swelling degree, ion exchange capacity (IEC), and ion conductivity. Then the surfaces of these membranes were modified by surface fluorination using 2000 ppm $F_2$ gas against $N_2$ gas for 1 h at room temperature. The surface fluorinated SPPO and APSf membranes were characterized again to determine any differences between the pristine and fluorinated membranes. In total, 3 types of bi-polar membranes were prepared by varying the IEC of the APSf and having a fixed value for the IEC of the SPPO. The hypochlorite concentration generated by using the surface fluorinated membranes was dependent on the IEC of the APSf and ranged from 683 to 826 ppm, while there was a considerable improvement in the durability of the surface fluorinated membranes as they remained intact even after operating for 4 h.

• Membrane Journal
• /
• v.27 no.5
• /
• pp.449-457
• /
• 2017

In this study, the 10 stages stacked module was designed by increasing the number of unit cells in the membrane capacitive deionization(MCDI) process. The aminated polysulfone and sulfonated poly(ether ether ketone) were synthesized and coated on porous carbon electrode by casting method. The salt removal efficiency was measured for the 10 stage stacked module under the operation conditions of adsorption voltage and time, desorption voltage and time, flow rate and concentration of feed water, and di-valent solutions including $CaSO_4$, $MgCl_2$ and tap water. Typically, when 100 mg/L of NaCl as the feed was used, the salt removal efficiency was 98.3% at a flow rate of 100 mL/min, the adsorption condition of 1.2 V/3 min and desorption condition of -0.5 V/5 min.

• Transactions of the Korean hydrogen and new energy society
• /
• v.17 no.2
• /
• pp.149-157
• /
• 2006

Hydrogen as new energy sources is highly efficient and have very low environmental emissions. The proton exchange membrane fuel cell (PEMFC) is an emerging technology that can meet these demands. Therefore, the preparation of stable polymeric membranes with good proton conductivity and durability are very important for hydrogen production via water electrolysis with PEM at medium temperature above $80^{\circ}C$. Currently Nafion of Dupont and Aciflex of Asahi, etc., solid polymer electrolytes of perfluorosulfonic acid membrane, are the best performing commercially available polymer electrolytes. However, these membrane have several flaws including its high cost, and its limited operational temperature above $80^{\circ}C$. Because of this, significant research efforts have been devoted to the development of newer and cheaper membranes. In order to make up for the weak points and to improve the mechanical characteristics with cross -linking, acid-base complexes were prepared by the combination PSf-co-PPSS-$NH_2$ with PEEK-$SO_3H$. The results showed that the proton conductivity decreased in 17.6% and 40% but tensile strength increased in 78% and 98%, about $20.65\;{\times}\;10^6N/m^2$, in comparison with SBPSf/HPA and SPEEK/HPA complex membrane.