• 한국항공우주학회지
• /
• 제31권9호
• /
• pp.32-37
• /
• 2003

소형화의 추세는 마이크로 로켓의 연구에도 적용되어 MEMS 공정으로 제작된 마이크로 로켓들이 시도되었다. 본 논문에서는 마이크로 밀링을 사용한 3차원 마이크로 로켓의 제작과 연소 및 발사시험의 결과를 다루고자 한다. 로켓의 동체는 알루미늄 6061 합금을 사용하였다. 3차원 마이크로 노즐은 황동을 직경 127${\mu}m$의 마이크로 엔드밀로 절삭하여 가공되었다. 두 가지 크기의 노즐이 제작되었는데 하나는 노즐목의 직경이 1mm이고 다른 하나는 0.5mm이다. 로켓의 질량은 7.32g이고 추진제의 질량은 0.65g이었다. 추력 대 무게비는 1.58에서 1.74로 계산되며 지면에서 45도 각도로 발사된 비행시험결과 약 46m~53m의 수평거리를 비행하였다.

• 환경위생공학
• /
• 제20권3호
• /
• pp.36-43
• /
• 2005

하수처리장 방류수의 재이용을 위해 2004년 1월$\~$12월까지 수질상태를 조사하였다. BOD, SS, 탁도, 총인과 색도의 월별로 조사한 연평균은 각각 4.1mg/L, 2.9mg/L, 0.8NTU, 1.3mg/L, 27unit이었다. 쟈테스트는 급속혼화 5분, 완속교반 15분, 침전 1시간의 조건하에서 오염물질의 제거율을 조사하였다. 사용된 응집제는 Alum과 폴리염화알루미늄이고, 방류수 중의 색도, 탁도, 총인, 총유기탄소 등을 제거하는데 효과가 있었다. 특히 폴리염화알루미늄을 사용시 탁도와 용존성인의 제거 효과가 좋았다. 응집공정과 연속한 정밀여과 공정에 의한 유기물의 제거효과를 조사한 결과, 분자량 1,000 Dalton 이상의 범위에 있는 물질의 제거가 잘 이루어진 반면, 소독부산물의 생성에 영향을 주는 분자량 500 Dalton 이하 물질의 제거율은 낮은 것으로 조사되었다. 따라서 복합공정에서 이 범위 분자량의 물질을 제거하기 위해 흡착공정 등의 추가공정이 필요할 것으로 본다.

• The Journal of Advanced Prosthodontics
• /
• 제10권3호
• /
• pp.205-210
• /
• 2018

PURPOSE. The purpose of this study was to evaluate the efficiency of a gas-phase fluorination method under different fluorination periods through using two resin cements. MATERIALS AND METHODS. 84 zirconia specimens in dimensions of $5mm{\times}5mm{\times}2mm$ were prepared and surface treated with $50{\mu}m$ aluminum oxide particles or gas phase fluorination for 2 min, 5 min, or 10 min. One specimen in each group was surface analyzed under scanning electron microscope. The remaining specimens were bonded to composite cylinders in dimensions of 2 mm diameter and 3 mm high with Panavia SA Plus or Variolink N. Then, the specimens were stored in $37^{\circ}C$ distilled water for 24 hours and shear bond strength test was applied at a speed of 1 mm/min. RESULTS. The highest shear bond strength values were observed in the samples fluorinated for 5 minutes and cemented with Panavia SA Plus. Variolink N did not elicit any statistical differences between surface treatments. Panavia SA Plus resin cement and Variolink N resin cements featured statistically significant difference in shear bond strength values only in the case of 5 minutes of fluorination treatment. CONCLUSION. According to the results of this study, application of 5 minutes of fluorination with 10-methacryloyloxydecyl dihydrogen phosphate monomer (MDP) containing Panavia SA Plus resin cement increased the resin bond strength of zirconia. Fluorination of the zirconia surface using conventional resin cement, Variolink N, did not lead to an increase in bond strength.

• The Journal of Advanced Prosthodontics
• /
• 제2권4호
• /
• pp.134-141
• /
• 2010

PURPOSE. The objective of this study was to evaluate fracture strength of collarless metal-ceramic FPDs according to their metal coping designs. MATERIALS AND METHODS. Four different facial margin design groups were investigated. Group A was a coping with a thin facial metal collar, group B was a collarless coping with its facial metal to the shoulder, group C was a collarless coping with its facial metal 1 mm short of the shoulder, and group D was a collarless coping with its facial metal 2 mm short of the shoulder. Fifteen 3-unit collarless metal-ceramic FPDs were fabricated in each group. Finished FPDs were cemented to PBT (Polybutylene terephthalate) dies with resin cement. The fracture strength test was carried out using universal testing machine (Instron 4465, Instron Co., Norwood MA, USA) at a cross head speed of 0.5 mm/min. Aluminum foil folded to about 1 mm of thickness was inserted between the plunger tip and the incisal edge of the pontic. Vertical load was applied until catastrophic porcelain fracture occurred. RESULTS. The greater the bulk of unsupported facial shoulder porcelain was, the lower the fracture strength became. However, there were no significant differences between experimental groups (P > .05). CONCLUSION. All groups of collarless metal-ceramic FPDs had higher fracture strength than maximum incisive biting force. Modified collarless metal-ceramic FPD can be an alternative to all-ceramic FPDs in clinical situations.

• 복식
• /
• 제55권5호
• /
• pp.101-107
• /
• 2005

In this article, mordant absorption rate by the Change of temperature and fabric, discharge level by water washing, mordant density and method in mordant dye are going to be handled. Besides, how treatment method will have an effect on absorption rate and color, is also going to be covered. An atom extinction photometer was used to measure the amount of mordant absorbed in fabric at each temperature and mordant type. It turned out that absorption rate differs according to the type of mordant and sample or temperature. Also it turned out that the mordant input amount has little influence on absorption rate, that is to say, if though you use more mordants, just tiny amount of mordant is going to be absorbed in cloth. It is true that the higher temperature goes up, the better mordant absorption gets. It is found that the type of mordant and sample, treatment period affects the discharge rate. Normally $15{\~}98\%$ mordant comes off the fabric by water washing, to be specific, $17{\~}47\%$ Iron by water washing and it has better performance on cotton and nylon than silk, $1\%{\~}52\%$ Aluminum by water washing and better absorption on silk, $36{\~}89\%$ Chrome by water washing and better absorption on silk, $50{\~}89\%$ copper by water washing and better absorption on silk, poor on cotton. The examination of the K/S values and colors between before and after soaping has been conducted under the circumstance that the test fabrics had been treated at $80^{\circ}C$ for 30 minutes with $0.2\%$ soaping solution. In case of pre-mordanted fabrics, the K/S value nosedived after soaping, meanwhile densely mordanted fabric's K/S value soared but after soaping, it dropped sharply. It turned out that soaping treatment deteriorates absorption much more than water washing. It's considered that $0.1 \%$ (W/V) of mordant density is appropriate.

• 대한기계학회논문집A
• /
• 제32권9호
• /
• pp.740-753
• /
• 2008

The conventional Split Hopkinson Pressure Bar (C-SHPB) technique with aluminum pressure bars to achieve a closer impedance match between the pressure bars and the specimen materials such as hot temperature degraded POM (Poly Oxy Methylene) and PP (Poly Propylene) to obtain more distinguishable experimental signals is used to obtain a dynamic behavior of material deformation under a high strain rate loading condition. An experimental modification with Pulse shaper is introduced to reduce the nonequilibrium on the dynamic material response during a short test period to increase the rise time of the incident pulse for two polymeric materials. For the dynamic stress strain curve obtained from SHPB experiment under high strain rate, the Johnson-Cook model is applied as a constitutive equation, and we verify the applicability of this constitutive equation to the probabilistic reliability estimation method. The methodology to estimate the reliability using the probabilistic method such as the FORM and the SORM has been proposed, after compose the limit state function using Johnson-Cook model. It is found that the failure probability estimated by using the SORM is more reliable than those of the FORM, and the failure probability increases with the increase of applied stress. Moreover, it is noted that the parameters of Johnson-Cook model such as A and n, and applied stress affect the failure probability more than the other random variables according to the sensitivity analysis.

• 대한기계학회논문집A
• /
• 제39권10호
• /
• pp.963-970
• /
• 2015

다양한 분야에서 금속 재료의 우수한 기계적 특성을 위해 경량화는 필수적이다. 최근에는 보다 효율적인 차체 경량화와 함께 내충격성 강화를 위하여 금속 부품 대신에 섬유 금속 적층판을 이용하는 연구가 활발히 진행되고 있다. 경량화를 위해서 자동차 및 항공기에서 복합재료나 샌드위치 구조로 이루어진 섬유 금속 적층판이 유용하다. 하지만, 섬유 금속 적층판 형태에 따른 기계적 특성이 도출되지 않은 실정이다. 본 논문에서는 적층판 두께 조합에 따른 특성 비교를 위하여 두께를 인자로 하고, 섬유 금속 적층판의 완전 요인 배치법으로 실험을 계획한다. 또한 유한요소 해석을 사용하여 알루미늄 판과 섬유 금속 적층판을 탄성과 소성 해석을 한다. 이를 통해 적층판 두께 조합에 따른 섬유 금속 적층판 형태에 따른 기계적 특성을 분석하고, 굽힘 대변형 거동을 예측하는 유한요소 해석모델을 구축한다.

• 설비공학논문집
• /
• 제20권3호
• /
• pp.189-196
• /
• 2008

The increase of system weight due to installation of cooling devices adds electrical and mechanical loads of humanoid robot, and in return, results in much heat. Therefore, the weight of cooling system is a critical issue for robot cooling. In this study, we propose non-metallic cold plates to deal with such problems. We compare thermal performances between one metallic cold plate and five different types of non-metallic cold plates. A metallic cold plate is totally made of copper. Five non-metallic PC(polycarbonate) cold plates, which are designed to reduce the overall weight of robot cooling system, are composed of a polycarbonate cover with different types of base plate. The overall heat transfer coefficients per unit mass and thermal resistances are obtained for the cold plates. The metallic cold plate shows the best thermal performance. It is interesting to note that the PC cold plate with an aluminum base plate with 18 channels shows the best overall heat transfer coefficient per unit mass. Most polycarbonate cold plates display fairly comparable thermal performance with more reduced system weight compared to the metallic cold plate.

• Tribology and Lubricants
• /
• 제20권6호
• /
• pp.306-313
• /
• 2004

Many of the current development in surface modification engineering are focused on multilayered coatings, which have the potential to improve the tribological properties. Four different multilayered coatings were deposited on AISI D2 steel in this study. The prepared samples are designed as $WC-Ti_{0.6}Al_{0.4}N,\;WC-Ti_{0.53}Al_{0.47}N,\;WC-Ti_{0.5}Al_{0.5}N\;and\;WC-Ti_{0.43}Al_{0.57}N$. The multilayered coatings were investigated with respect to coating surface and cross-sectional morphology, roughness, adhesion, hardness, porosity and tribological behaviors. Especially, wear tests of four multilayered coatings were performed by using a ball-on-disc configuration with a linear sliding speed of 0.017 m/sec and a normal load of 5.38 N load. The tests were carried out at room temperature in air by employing AISI 52100 steel ball $(H_R\;=\;66) $ having a diameter of 10 mm. The surface morphology, and topography of the wear scars of samples and balls have been determined by using scanning electron spectroscopy (SEM). Also, wear mechanism was determined by using SEM coupled with energy-dispersive spectroscopy (EDS). Results have showed an improved wear resistance of the $WC-Ti_{1-x}Al_xN$coatings with increasing of Al (aluminum) concentration.

• 소성∙가공
• /
• 제18권4호
• /
• pp.296-303
• /
• 2009

The effect of porosity on the high-cycle fatigue properties of Al-Si-Mg casting aluminum alloys was investigated in this study. Microstructure examination, tensile and high-cycle fatigue test were conducted on both Al-Si-Mg casted (F) and heat-treated (T6) conditions. Porosity characteristics on the fracture surfaces of fatigue-tested samples were examined using SEM and image analysis. The microstructure observation results showed that eutectic Si particles were homogeneously dispersed in the matrix of the Al-Si-Mg casting alloys, but there were porosities formed as cast defects. The high-cycle fatigue results indicated that the fatigue strength of the 356-T6 alloy was higher than that of the 356-F alloys because of the significant reduction in volume fraction of pores by heat treatment. The SEM fractography results showed that porosity affected detrimental effect on the fatigue life: 80% of all tested samples fractured as a result of porosity which acted as the main crack initiation site. It was found that fatigue life decreased as the size of the surface pore increased. A comparison was made between surface pore and inner pore for its effect on the fatigue behavior. The results showed that the fatigue strength with the inner pores was higher than that of the surface pore.