• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1340-1345
• /
• 2004

Convective boiling heat transfer coefficients of R-22 were obtained in a flat extruded aluminum tube with $D_h=1.41mm$ . The test range covered mass flux from 200 to 600 $kg/m^2s$, heat flux from 5 to 15 $kW/m^2$ and saturation temperature from $5^{\circ}C$ to $15^{\circ}C$ . The heat transfer coefficient curve shows a decreasing trend after a certain quality(critical quality). The critical quality decreases as the heat flux increases, and as the mass flux decreases. The early dryout at a high heat flux results in a unique 'cross-over' of the heat transfer coefficient curves. The heat transfer coefficient increases as the mass flux increases. At a low quality region, however, the effect of mass flux is not prominent. The heat transfer coefficient increases as the saturation temperature increases. The effect of saturation temperature, however, diminishes as the heat flux decreases. Both the Shah and the Kandlikar correlations underpredict the low mass flux and overpredict the high mass flux data.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제12권3호
• /
• pp.148-157
• /
• 2004

Convective boiling heat transfer coefficients of R-22 were obtained in a flat extruded aluminum tube with $D_h=1.41mm$. The test range covered mass flux from 200 to $600kg/m^{2}s$, heat flux from 5 to $15kW/m^2$ and saturation temperature from $5^{\circ}C\;to\;15^{\circ}C$. The heat transfer coefficient curve shows a decreasing trend after a certain quality (critical quality). The critical quality decreases as the heat flux increases, and as the mass flux decreases. The early dryout at a high heat flux results in a unique 'cross-over' of the heat transfer coefficient curves. The heat transfer coefficient increases as the mass flux increases. At a low quality region, however, the effect of mass flux is not prominent. The heat transfer coefficient increases as the saturation temperature increases. The effect of saturation temperature, however, diminishes as the heat flux decreases. Both the Shah and the Kandlikar correlations un-derpredict the low mass flux and overpredict the high mass flux data.

• 한국재료학회지
• /
• 제33권3호
• /
• pp.95-100
• /
• 2023

This research examines the effect of adding aluminum on the structural, phasic, and magnetic properties of CoCrFe NiMnAl_x high-entropy alloys. To this aim, the arc-melt process was used under an argon atmosphere for preparing cast samples. The phasic, structural, and magnetic properties of the samples were characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), and vibrational magnetometry (VSM) analyses. Based on the results, the addition of aluminum to the compound caused changes in the crystalline structure, from FCC solid solution in the CoCrFeNiMn sample to CoCrFeNiMnAl BBC solid solution. It was associated with changes in the magnetic property of CoCrFeNiMnAl_x high-entropy alloys, from paramagnetic to ferromagnetic. The maximum saturation magnetization for the CoCrFeNiMnAl casting sample was estimated to be around 79 emu/g. Despite the phase stability of the FCC solid solution with temperature, the solid solution phase formed in the CrCrFeNiMnAl high-entropy compound was not stable, and changed into FCC solid solution with temperature elevation, causing a reduction in saturation magnetization to about 7 emu/g.

• Journal of Microbiology and Biotechnology
• /
• 제25권7호
• /
• pp.978-987
• /
• 2015

Aluminum (Al) toxicity is one of the greatest limitations to agriculture in acid soils, particularly in tropical regions. Arbuscular mycorrhizal fungi (AMF) can supply plants with nutrients and give protection against Al toxicity. The aim of this work was to evaluate the effects of soil liming (i.e., reducing Al saturation) on the AMF community composition and structure in the roots of maize lines contrasting for Al tolerance. To this end, we constructed four 18S rDNA cloning libraries from L3 (Al tolerant) and L22 (Al sensitive) maize lines grown in limed and non-limed soils. A total of 790 clones were sequenced, 69% belonging to the Glomeromycota phylum. The remaining sequences were from Ascomycota, which were more prominent in the limed soil, mainly in the L3 line. The most abundant AM fungal clones were related to the family Glomeraceae represented by the genera uncultured Glomus followed by Rhizophagus and Funneliformis. However, the most abundant operational taxonomic units with 27% of the Glomeromycota clones was affiliated to genus Racocetra. This genus was present in all the four libraries, but it was predominant in the non-limed soils, suggesting that Racocetra is tolerant to Al toxicity. Similarly, Acaulospora and Rhizophagus were also present mostly in both lines in non-limed soils. The community richness of AMF in the non-limed soils was higher than the limed soil for both lines. The results suggest that the soil Al saturation was the parameter that mostly influences the AMF species composition in the soils in this study.

• 마이크로전자및패키징학회지
• /
• 제7권3호
• /
• pp.37-44
• /
• 2000

Electrochemical impedance spectroscopy (EIS)를 이용하여 에폭시 수지 조성물이 코팅된 알루미늄 패드의 부식거동을 연구하였다. 에폭시 수지 조성물은 반도체 패키지 봉지용으로써 80 wt%의 충전재를 포함하고 있으며, $100^{\circ}C$의 끊는 가혹 조건에서 탈이온수 (deionized water)를 사용하여 에폭시 조성들에 침투시켰다. 흡습이 진행되면서 에폭시 조성물 및 알루미늄/에폭시 계면에서의 저항 감소와 커패시턴스 증가가 관찰되었으며 , 약 170 시간까지는 물분자와 유기물로부터 발생된 이온이 에폭시 조성물에 포화되고, 그 이후에는 계면에 침투하여 금속의 부식을 발생시키는 것을 알 수 있었다. 수분 흡습에 따른 에폭시 조성물/금속간의 접착강도 측정으로부터 계면에 물분자 및 이온이 포화됨에 따라 접착강도가 감소하는 것을 예상할 수 있었으며, 반도체 패키지용 에폭시 수지 조성물에 의한 알루미늄 전극의 부식을 방지하기 위해서는 충전재의 함량증가가 필수적이라는 것을 알 수 있었다.

• 한국통신학회논문지
• /
• 제19권11호
• /
• pp.2228-2237
• /
• 1994

This paper describes the development of a Ku-band ($12.25GHz\sim12.75GHz$) SSPA intended as a replacement for TWTAs used in communication satelite transponder. The power stage of the amplifier consists of tow intrmally matched 8W FET divices combined using the branch-line coupler. To operate this stage, the drive stage has been designed with intermally matched 2W, 4W, 8W FET and two medium power FETs. The entire amplifier is made up by a aluminum chassis housing both the RF circuit and the bias circuitry. A regrlator/sequencing circuitry is used for FET biasing. The amplifier results implemented in this way show $41\pm0.3dB$ small-signal gain, 15W saturation power, a typical two tone $IM_3=-21.5dBc$ with single carrier backed off 5dB from saturation, $2^*/dBmax$ AM/PM conversion, and $3.47\pm0.25nsec$ group delay.

• 한국산학기술학회논문지
• /
• 제16권5호
• /
• pp.3006-3013
• /
• 2015

원관 열교환기보다 납작관 열교환기를 사용하면 전열성능을 한층 향상시킬 수 있다. 납작관 열교환기를 적절히 설계하기 위해서는 관 내측 열전달계수를 알아야 한다. 본 실험에서는 수력직경 1.41mm인 알루미늄 납작관 내 R-410A 대류 비등 열전달계수를 구하였다. 실험범위는 질량유속 $200{\sim}600kg/m^2s$, 열유속 $5{\sim}15kg/m^2$, 포화온도 $5{\sim}15^{\circ}C$이다. 실험 결과 열전달계수는 임계 건도를 기점으로 감소함을 보였다. 임계 건도는 열유속이 증가할수록 감소하고, 질량유속이 감소할수록 감소하였다. 이는 높은 열유속 또는 낮은 질량유속에서 대류의 영향이 작게 되고 따라서 조기에 dryout이 발생되기 때문에 나타나는 현상으로 판단된다. 열전달계수는 질량유속이 증가할수록 증가하였다. 그러나 낮은 건도에서는 질량유속의 영향은 미미하였다. 열전달계수는 포화온도가 증가할수록 증가하였다. 하지만 이런 경향은 열유속이 작아지면 감소하였다. Shah와 Kaew-On et al. 상관식은 본 실험자료를 적절히 예측하였다.

• 열처리공학회지
• /
• 제23권6호
• /
• pp.331-337
• /
• 2010

Aluminum nitride (AlN) thin films containing various amounts of Co content have been deposited by using a two-facing targets type sputtering (TFTS) system. The deposited films were also annealed successively and isothermally at different temperatures. Annealing treatment can control the physical properties as well as the microstructure of AlN films with Co particles. High magnetization and high resistivity are obtainable in AlN films containing dispersed Co particles. The coercivity of the films does not depend on annealing time, but it increases with increasing annealing temperature due to the increase of the grain size. A high saturation magnetization of 46 kG and resistivity of 2200 ${\mu}{\Omega}$-cm was obtained for AlN films containing 25 at% Co.

• 한국의학물리학회지:의학물리
• /
• 제16권4호
• /
• pp.202-206
• /
• 2005

Magnesium Aluminum Spinel ($MgAl_2O_4$)은 자외선 선량계에로 응용성을 가지고 있는 Aluminum oxide와 유사한 물리 화학적 특성을 가지고 있다. $MgAl_2O_4$의 자외선 선량계로 응용하기 위한 열자자극발광 특성을 조사하였다. 자외선 조사된 $MgAl_2O_4$의 3차원 열자극발광 스펙트럼을 300${\~}$600 K 및 300${\~}$800 nm 범위에서 측정하였다. 자외선 조사시간의 증가함에 따라 열자극발광 곡선의 정점 온도는 낮은 쪽으로 이동하였다. 476 K 정점의 열자극발광 곡선은 second-order kinetics이고, 활성화 에너지 및 이탈진동수는 각각 0.85 eV 및 $1.92{\times}10^6\;sec^{-1}$이다. 열자극발광 스펙트럼은 530 nm 및 700 nm 방출 스펙트럼으로 나눠지고, 이들은 각각 $V^{2+}$와 $Cr^{2+}$에 포획된 양공에 기인한다. 700 nm 열자극발광의 선형성이 530 nm 보다 작은 반면, 700 nm 열자극발광의 포화는 530 nm 보다 더 많은 조사시간에서 나타난다.

• The Korean Journal of Ceramics
• /
• 제1권2호
• /
• pp.91-95
• /
• 1995

Polycrystalline bismuth- and aluminum- substituted dysporsium and yttrium iron garnet (Bi2R3-xAlyFe5-yO12, R=Dy or Y, $0\leqx\leq3, \; 0\leqy\leq3$) films have been prepared by pyrolysis. The crystallization temperatures, the solubility limit of bismuth ions into the garnet phase, and magnetic and magneto-optic properties of the films have been investigated as a function of bismuth and aluminum concentration. It was found that the crystallization temperatures as a function of bismuth and aluminum concentration. It was found that the crystallization temperatures of these films rapidly decreased as bismuth concentration. It was found that the crystallization temperatures of these films rapidly decreased as bismuth concentration (x) increased up to x=1.5 and then remained temperatures of these films rapidly decreased as bismuth concentration (x) increased up to x=1.5 and then remained unchanged at x>1.5, whereas, showed no changes as aluminum concentration (y) increased up to y=1.0 and then gradually increased at y>1.0. The solubility limit of bismuth ions was x=1.8 when y=0 but increased to x=2.3 when y=1.0. It was demonstrated that the magnetic and magneto-optic properties of the dysprosium iron garnet films could be tailored by bismuth and aluminum substitution suitable for magneto-optic recording as follows. The saturation magnetization and coercivity data obtained for the films indicated that the film composition at which the magnetic compensation temperature became room temperature was y=1.2 when x=1.0. Near this composition the coercivity and the squareness of the magnetic hysteresis loop of the films were several kOe and unit, respectively. The Curie temperatures of the films increased with the increase of x but decreaed with the increase of y, and was 150-$250^{\circ}C$ when x=1.0 and y=0.6-1.4. The Faraday rotation at 633 nm of the films increased as x increased but decreased as y increased, and was 1 deg/$\mu\textrm{m}$ when x=1.0 and y=1.0. Based on the data obtained, the appropriate film composition for magneto-optic recording was estimated as near x=1.0 and y=1.0 or $BiDy_2AlFe_4O_{12}$.