• Design & Manufacturing
• /
• 제13권4호
• /
• pp.23-27
• /
• 2019

People's interest in the environmental problems of the Earth is growing as they come to the modern world, and research is being actively conducted on how to protect the environment. As a result, the automobile industry, one of the causes of environmental pollution, is also affected. Therefore, research is being conducted to improve the fuel economy and light weight of cars, development of pollution-free cars such as electric cars, and aluminium materials that are lighter than ordinary steel sheets and easier to recycle are gaining attention. In this experiment, the material was formed to form a form of aluminium and the material reduction rate of the side wall of the foam was tested according to the amount of side wall. The material used in the experiment was A3003-O, which is less plastic than normal steel plates, but has excellent corrosion resistance, plasticity and weldability compared to aluminium materials, but has poor tensile strength. For tensile testing, a certain array of Forming Shapes was molded and the height of the Forming was set to 5mm, and the height of the Forming was 4.7mm, indicating that the difference between the first 5mm Forming and the height was not large. In addition, the material reduction rate was tested by giving 15, 0, and -0.15 teas, respectively, and was found to be valuable as a product only for -0.15.

• 대한기계학회논문집A
• /
• 제36권12호
• /
• pp.1551-1561
• /
• 2012

플레저 선박은 주로 FRP(Fiber reinforced plastic)를 주재료로 제작되고 있으나 2000년대에 들어오면서 FRP 선체에 대한 환경오염 및 해양안전에 관한 법규 규제가 강화되고 있다. 즉, FRP는 재활용이 불가능하며 폐기시 자연에서 분해되는 데 100년이상 걸리는 매우 반환경적 특성을 가지고 있다. 일반 선체 재료로서는 강, 알루미늄, FRP를 제안하고 있으며 이에 따른 구조설계규격 및 재료설계강도를 제안하고 있다. 그러나 소형 선박에 적합한 염가 재료에 대한 연구는 전혀 진행되지 않고 있으며 단지 소형조선산 업계에서 카누나 카약 선체를 폴리에틸렌을 이용하여 제작하여 판매하고 있다. 따라서 본 연구에서는 고 밀도 폴리에틸렌을 이용하여 보트를 설계 및 제작하기 위하여 실적선을 기초로 선체의 선형을 완성한 뒤 ISO 12215-5의 소형 선체에 대한 구조설계기준을 적용하여 선체 치수를 결정하였다.

• Structural Engineering and Mechanics
• /
• 제35권5호
• /
• pp.571-592
• /
• 2010

An energy-based fatigue life prediction framework was previously developed by the authors for prediction of axial, bending and shear fatigue life at various stress ratios. The framework for the prediction of fatigue life via energy analysis was based on a new constitutive law, which states the following: the amount of energy required to fracture a material is constant. In the first part of this study, energy expressions that construct the constitutive law are equated in the form of total strain energy and the distortion energy dissipated in a fatigue cycle. The resulting equation is further evaluated to acquire the equivalent stress per cycle using energy based methodologies. The equivalent stress expressions are developed both for biaxial and multiaxial fatigue loads and are used to predict the number of cycles to failure based on previously developed prediction criterion. The equivalent stress expressions developed in this study are further used in a new finite element procedure to predict the fatigue life for two and three dimensional structures. In the second part of this study, a new Quadrilateral fatigue finite element is developed through integration of constitutive law into minimum potential energy formulation. This new QUAD-4 element is capable of simulating biaxial fatigue problems. The final output of this finite element analysis both using equivalent stress approach and using the new QUAD-4 fatigue element, is in the form of number of cycles to failure for each element on a scale in ascending or descending order. Therefore, the new finite element framework can provide the number of cycles to failure at each location in gas turbine engine structural components. In order to obtain experimental data for comparison, an Al6061-T6 plate is tested using a previously developed vibration based testing framework. The finite element analysis is performed for Al6061-T6 aluminum and the results are compared with experimental results.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.83-87
• /
• 2001

A 110 mm diameter aspheric metal secondary mirror for a test model of an earth observation satellite camera was fabricated by ultra-precision single point diamond turning (SPDT). Aluminum alloy for mirror substrates is known to be easily machinable, but not polishable due to its ductility. A harder material, Ni, is usually electrolessly coated on an Al substrate to increase the surface hardness for optical polishing. Aspheric metal secondary mirror without a conventional polishing process, the surface roughness of Ra=10nm, and the form error of $Ra={\lambda}/12({\lambda}=632nm)$ has been required. The purpose of this research is to find the optimum machining conditions for reflector cutting of electroless-Ni coated Al alloy and apply the SPDT technique to the manufacturing of ultra precision optical components of metal aspheric reflector.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.34-41
• /
• 2004

The purpose of this paper is to look at the characteristics of surface finishing which is one of the form accuracies and to obtain the fundamental technical data from the process of machining with diamond tool through experiment and theoretical analysis. The experiments were conducted with domestic made ultra-precision machine and MCD.PCD tool, with aluminum alloyed material and brass being used for the work pieces. The goal of the size accuracy was set to 100nm. The most suitable tool nose radius and machining conditions were selected, and the variations of the surface roughness were observed using SEM method while machining the distance of up to 500km. These data were evaluated and they examined the variation of the machined surfaces while cutting up to 500km of machining distance. At the same time, the state for the wear of diamond tool nose was analyzed and carefully examined through the newest measuring device. Additionally, the characteristics of ultra-precision machining technology were studied through visual analysis.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.565-573
• /
• 2007

This paper is concerned with the dynamic modeling, active vibration controller design and experiments for a cylindrical shell equipped with MFC actuators. The dynamic model was derived by using Rayleigh-Ritz method based on Donnel-Mushtari shell theory. The actuator and sensors for the MFC actuator equations were derived based on pin-force model. The equations of motion were then reduced to modal equations of motion by considering the modes of interest. The sensor equations were also converted to a reduced form. An aluminum shell was fabricated to demonstrate the effectiveness of modeling and control techniques. The boundary conditions at both ends of the shell were assumed to be shear diaphragm. Theoretical natural frequencies were calculated and compared to experimental result. It was observed that the theoretical result is in good agreement with experimental result for the first two modes. The multi-input and multi-output positive position feedback controller, which can cope with first two modes, was then designed based on the blockinverse theory and implemented using DSP. It was found from experiment that vibrations can be successfully suppressed.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 2011년도 한국우주과학회보 제20권1호
• /
• pp.31.4-32
• /
• 2011

The previous KRISS profilometer design used an aluminum profile structure to which a bar-type reference mirror subsystem and the measurement subsystem are mounted. The earlier design suffers from low stiffness as shown from the first resonance mode of 45.1 Hz. The improved mechanical design we describe in this study replaces the aluminium profile structure with a granite structure of $1340{\times}220{\times}230$ in dimension. The finite element analysis results for the revised design show 0.001 degree in probe contact angle variation. The first resonance mode was computed to 91.2 Hz that is much better than 45.1 Hz from the previous design. We describe the improved design, structural analysis results and how these results would satisfy the form accuracy requirement of 1 ${\mu}m$ PV.

• 한국항해학회지
• /
• 제9권2호
• /
• pp.43-63
• /
• 1985

As a circular cylinder has a comparatively simple shape and becomes a basic problem for flows around other various shapes of bodies, the problem of two-dimensional viscous flow around the circular cylinder has been investigated, both theoretically and experimentally. But not a few problems are left unsolved. It is well known that the calculations are successfully made with the approximations of Stokes or Oseen for very low Reynolds numbers, but as Reynolds number is increased, Oseen's approximations as well as Stokes's ones become more and more remote from the exact solution of the Navier-Stokes equations. Therefore, in this paper, the authors transform the Navier-Stokes equations into the finite difference equations in the steady two-dimensional viscous flow at Reynolds number up to 45, and then solve the solution of the Navier-Stokes equations numerically. Also, the authors examine the accuracy of the solution by means of flow visualization with aluminum powder. The main results are as follows; (1) The critical Reynolds number at which twin vortices begin to form in the rear of the circular cylinder is found to be 6 in the experiment and 4 in the numerical solution. (2) As Reynolds number is increased, it is proved that the ratio of the length of the twin vortices to the diameter is grown almost linearly, both experimentally and numerically. (3) Separation angle is also increased according to reynolds number. But it is found that it would converge into 101.3 degrees, both experimentally and numerically.

• 한국응용과학기술학회지
• /
• 제2권1호
• /
• pp.19-23
• /
• 1985

In order to know the quality changes of the fat and oil foods packed in plastics film by the sunlight, we examined the sunlight transmitting rate by the kind of films and measured the acid value and peroxide value according to it. The results obtained were as follows : 1. The sunlight transmitting rate of various films was explained especial permeability under the wavelength of less than 300nm, but it marked a regular form under that of more than 30nm. 2. The vacuum evaporation film with aluminum on the polyester shuts off most of the sunlight, therefore, it has the best effect that keeps the fats and oils off rancidity. 3. The sunlight transmitting rate of the white color printing film drops about 80% as compared with not printing. 4. The preventive power against the rancidity of fats and oils is PET/Al, PET, PE, nylon and OPP film in that order. The changes of peroxide value and acid value were approximately the same as that of the sunlight transmitting rate.

• 상하수도학회지
• /
• 제31권6호
• /
• pp.521-527
• /
• 2017

Phosphorus is one of the limiting nutrients for the growth of phytoplankton and algae and is therefore one of leading causes of eutrophication. Most phosphorous in water is present in the form of phosphates. Different technologies have been applied for phosphate removal from wastewater, such as physical, chemical precipitation by using ferric, calcium or aluminum salts, biological, and adsorption. Adsorption is one of efficient method to remove phosphates in wastewater. To find the optimal media for phosphate removal, physical characteristics of media was analysed, and the phosphate removal efficiency of media (silica sand, slag, zeolite, activated carbon) was also investigated in this study. Silica sand showed highest relative density and wear rate, and phosphate removal efficiency. Silica sand removed about 36% of phosphate. To improve the phosphate removal efficiency of silica sand, Fe coating was conducted. Fe coated silica sand showed 3 times higher removal efficiency than non-coated one.