• Korean Journal of Materials Research
• /
• v.34 no.1
• /
• pp.12-20
• /
• 2024

This study successfully prepared high-porosity aluminosilicate fibrous porous ceramics through vacuum suction filtration using aluminosilicate fiber as the primary raw material and glass powder as binder, with the appropriate incorporation of glass fiber. The effects of the composition of raw materials and sintering process on the structure and properties of the material were studied. The results show that when the content of glass powder reached 20 wt% and the samples were sintered at the temperature of 1,000 ℃, strong bonds were formed between the binder phase and fibers, resulting in a compressive strength of 0.63 MPa. When the sintering temperatures were increased from 1,000 ℃ to 1,200, the open porosity of the samples decreased from 89.08 % to 82.38 %, while the linear shrinkage increased from 1.13 % to 10.17 %. Meanwhile, during the sintering process, a large amount of cristobalite and mullite were precipitated from the aluminosilicate fibers, which reduced the performance of the aluminosilicate fibers and hindered the comprehensive improvement in sample performance. Based on these conditions, after adding 30 wt% glass fiber and being sintered at 1,000 ℃, the sample exhibited higher compressive strength (1.34 MPa), higher open porosity (89.13 %), and lower linear shrinkage (5.26 %). The aluminosilicate fibrous porous ceramic samples exhibited excellent permeability performance due to their high porosity and interconnected three-dimensional pore structures. When the samples were filtered at a flow rate of 150 mL/min, the measured pressure drop and permeability were 0.56 KPa and 0.77 × 10^-6 m² respectively.

• Journal of the Optical Society of Korea
• /
• v.17 no.2
• /
• pp.182-187
• /
• 2013

We present a comparative experimental analysis of the thermal spectroscopic characteristics of a phosphosilicate (P)-based ytterbium-doped fiber (YDF) against an aluminosilicate (Al)-based YDF in the temperature range of 25 to $150^{\circ}C$. We also characterize the fibers as gain media in a cladding-pumped amplifier configuration. While both fibers exhibit comparable trends in their thermal characteristics, there are noticeable distinctions in the fluorescence lifetime reduction rate and the spectral dependence of the transition cross-sections. The P- and Al-based YDFs present thermal lifetime reduction rates of $0.012%/^{\circ}C$ and $0.026%/^{\circ}C$, respectively. In particular, in the spectral region at ~940 nm, the absorption cross-section of the P-based YDF undergoes significantly less thermal change compared to that of the Al-YDF. In the cladding-pumped amplifier configuration operating at a total gain of 10 dB, the Al-based YDF generally performs betters than the P-based YDF in the temperature range of 25 to $75^{\circ}C$. However, it is highlighted that in the high temperature range of over $75^{\circ}C$, the latter shows a less gain reduction rate than the former, thereby yielding higher relative output power by 3.3% for a 1060-nm signal, for example.

• Proceedings of the Optical Society of Korea Conference
• /
• 2000.02a
• /
• pp.214-215
• /
• 2000

As silica based optical fibers and preforms are processed at a high temperature, residual stresses are bulit in the strucure when cooled down to the room temperature. The magnitude of the residual stress depends on the difference in the thermal expansion coefficients between core and cladding glass as well as on the temperature difference. Residual stress distribution determines the intrinsic strength and could affect the long term reliability of optical fibers. And furthermore, stress can introduces anisotropy into optical fibers by photoelastic effects. The analysis of thermal stress has been intensively studied for multimode fibers$^{(1)}$ and the authors and co-wokers recently reported the stress distribution in a depressed inner cladding structure$^{(2)}$ . The compositions of the glass in the previous studies, however, have been restricted to conventional glass formers, such as GeO2, B2O3, P2O5, Fluorine. (omitted)