• Journal of Energy Engineering
• /
• v.8 no.2
• /
• pp.272-278
• /
• 1999

In the present study, measurements of thermal contact resistance (TCR) were conducted for joints of brass and aluminium cylinders of 30 mm in diameter, 45 mm in length, when their interfaces were; ⅰ) under vacuum, ⅱ) charged with a pure silicone grease and ⅲ) charged with a mixture of silicone grease and powder of aluminium (#325). Also the data were compared with analytical calculations using Fouche's model. The data of TCR for joints under vacuum state varied in the range of (2∼100)${\times}$10$\^$-5/(㎡$^{\circ}C$/W) depending on their surface roughness. When the contact surfaces were carefully ground, a reduction of 30∼50% in TCR was obtained. But the surface treatment with silicone grease gave rise to a reduction of about 5∼10 times more than that of vacuum state. The analytical prediction by Fouche's model showed a good agreement within 10~30%, for the case of contact surface charged with silicone grease.

• Corrosion Science and Technology
• /
• v.4 no.6
• /
• pp.217-221
• /
• 2005

In the present investigation, holographic interferometry was utilized for the first time to monitor in situ the thickness of the oxide film of aluminium samples during anodization processes in boric acid solutions. The anodization process (oxidation) of the aluminium samples was carried out by the technique of the electrochemical impedance spectroscopy(EIS), in different concentrations of boric acid (0.5-5.0% $H_3BO_3$) at room temperature. In the mean time, the real-time holographic interferometry was used to measure the thickness of anodized (oxide) film of the aluminium samples in solutions. Consequently, holographic interferometry is found very useful for surface finish industries especially for monitoring the early stage of anodization processes of metals, in which the thickness of the anodized film of the aluminium samples can be determined without any physical contact. In addition, measurements of electrochemical values such as the alternating current (A.C) impedance(Z), the double layer capacitance($C_{dl}$), and the polarization resistance(Rp) of anodized films of aluminium samples in boric acid solutions were made by the electrochemical impedance spectroscopy(EIS). Attempts to measure electrochemical values of Z, Cdl, and Rp were not possible by holographic interferometry in boric acid especially in low concentrations of the acid. This is because of the high rate of evolutions of interferometric fringes during the anodization process of the aluminium samples in boric acid, which made measurements of Z, Cdl, and Rp are difficult.

• Korean Chemical Engineering Research
• /
• v.45 no.2
• /
• pp.117-123
• /
• 2007

The effect of aluminium addition to MCM-41 on product yield and carbon number distribution was investigated in the catalytic cracking of a polymer mixture, LDPE, LLDPE, and EVA copolymer, with a composition similar to that found in real agricultural film wastes. Al-MCM-41 catalyst synthesized by post-synthetic grafting method (Al-MCM-41-P) as well as Al-MCM-41 catalyst synthesized by direct sol-gel (Al-MCM-41-D). The catalytic cracking of polymer mixture was carried out in vapor phase contact as well as in liquid phase contact. The amount of acid sites increased with aluminium addition by post method as well as direct method, which was seemed to be due to Lewis acid sites. In liquid phase catalytic cracking, the yield of light hydrocarbon fraction increased with aluminium addition. The effect of aluminium addition on production of $C_5-C_{12}$ hydrocarbons over Al-MCM-41-P catalysts was greater than that over Al-MCM-41-D catalysts. In the case of vapor phase catalytic cracking, the effect of aluminium addition was smaller than that of liquid phase catalytic cracking. The selectivity to $C_{13}-C_{32}$ hydrocarbons was smaller in vapor phase catalytic cracking.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.1
• /
• pp.46-49
• /
• 2016

A thin film transistor (TFT) has been fabricated using the amorphous 0.5 wt% Si doped zinc-tin-oxide (a-0.5 SZTO) with different electrodes made of either aluminium (Al) or titanium/aluminium(Ti/Al). Contact resistance and total channel resistance of a-0.5SZTO TFTs have been investigated and compared using the transmission line method (TLM). We measured the total resistance of 1.0×10² Ω/cm using Ti/Al electrodes. This result is due to Ti, which is a material known for its adhesion layer. We found that the Ti/Al electrode showed better contact characteristics between the channel and electrodes compared with that made of Al only. The former showed a less contact and total resistance. We achieved high performance of the TFTs characteristic, such as Vth of 2.6 V, field effect mobility of 20.1 cm² V⁻¹s⁻¹, S.S of 0.9 Vdecade⁻¹, and on/off current ratio of 9.7×10⁶ A. It was demonstrated that the Ti/Al electrodes improved performance of TFTs due to enhanced contact resistance.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.1
• /
• pp.95-101
• /
• 2000

The effect of surface contact angle on the behavior of frost formation in a fin-tube heat exchanger is investigated experimentally. It is shown that both heat exchangers with hydrophilic and hydrophobic surfaces appear to have a better thermal performance than bare aluminium heat exchanger, but the improvements are very small. There is a little increase in the amount of the frost deposited onto the heat exchanger with both hydrophilic and hydrophobic surface. However, the effect of contact angle on the frost density is observed ; the frost with high density forms on the heat exchanger with hydrophilic surface ; and the frost with low density is deposited onto the heat exchanger with hydrophobic surface when compared with the frost deposited onto the heat exchanger with bare aluminium surface. This may be attributed to the fact that the shape of water droplets which condense on the surface of heat exchanger at the early stage of frosting varies with contact angle, and thus makes a difference on the structure of frost formation. From the experiments with different relative humidity of inlet air, it is shown that the variations of operating parameter make no influence on the effect of surface contact angle on the frosting behavior in the heat exchanger.

• Proceedings of the KWS Conference
• /
• 1997.10a
• /
• pp.184-193
• /
• 1997

Aluminium and aluminium alloys have the high electrical and heat conductivity. It gives rise to difficulties for a choice of electrodes material for their contact electric welding. This paper describes the investigations performed to solve the above problem. The purpose of this investigation was to obtain dispersion-hardening alloys by the internal oxidation method, to optimize their contents and treatment modes, to produce electrodes of these alloys and to test them. The strengthing effect of alloys with oxide particles depends on their size stability at high temperatures. Despite of the fact, that oxides are the most stable of all the non-metallic phases their coagulation takes place. Based on the early results, we chose two types of alloys, first No. 1 Cu - 0,4%Al and second No. 2 Cu - 0,2%Be for production of electrodes. These alloys had not additional alloying elements. These alloys were prepared as 1 mm plates and flake-formed 200 m thick, and also No. 1 as a powder of size 100 mkm (received from Korea). The large samples for electrodes were produced by three methods : explosive welding method, dynamic one including the explosion compression of electrode blank and the quasi-dynamic method including the high-speed compression of dense briquest and the further hot extrusion of a rod.

• Corrosion Science and Technology
• /
• v.15 no.4
• /
• pp.166-170
• /
• 2016

The combined process of porous type anodizing and desiccation treatment was applied to improve wettability of A1050 aluminum alloy. The water contact angles of anodized samples were increaseds considerably with desiccation treatment. However, there was no considerable effect of polishing and anodizing time on water contact angle. The corrosion behavior with the treatments was investigated electrochemically. The corrosion resistance of the samples in 3.5 mass% NaCl solutions increased with higher contact angle. Anodized and desiccated samples showed better corrosion resistance than un-desiccated samples around rest potential region.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.10-19
• /
• 1998

The erosion of electrode in spot welding of aluminium alloy by direct current is dependent on the electric polarity. The positive electrode is much more eroded than the negative one. To explain this phenomenon, Peltier effect has been generally accepted as a unique theory. In this study Peltier effect was evaluated by calculations on the basis of some references and experiments. The difference of heat generated by Peltier effect on both electrode surfaces was, however, only 4% of total heat generated during wel- ding. Because of insufficient explanation, Kohler theory, which is mainly affected by thin oxide film, was introduced. A theoretical calculation showed 17% of the temperature difference between the positive and negative electrode, in case "surface voltage" resulted from oxide film was 30% of total contact voltage. This revealed that the erosion of electrode could be more affected by Kohler theory than effect.an effect.

• Corrosion Science and Technology
• /
• v.15 no.6
• /
• pp.314-319
• /
• 2016

Reduced activation ferritic-martensitic steels (RAFM) are envisaged in future fusion technology as structural material which will be in direct contact with a flowing liquid lead-lithium melt, serving as breeder material. Aluminium-based coatings had proven their ability to protect the structural material from corrosion attack in flowing Pb-15.7Li and to reduce tritium permeation into the coolant, significantly. Coming from scales produced by hot dipping aluminization (HDA), the development of electrochemical-based processes to produce well-defined aluminium-based coatings on RAFM steels gained increased attention in research during the last years. Two different electrochemical processes are described in this paper: The first one, referred to as ECA, is based on the electrodeposition of aluminium from volatile, metal-organic electrolytes. The other process called ECX is based on ionic liquids. All three processes exhibit specific characteristics, for example in the field of processability, control of coating thicknesses (low activation criteria) and heat treatment behavior. The aim of this article is to compare these different coating processes critically, whereby the focus is on the comparison of ECA and ECX processes. New results for ECX will be presented and occurring development needs for the future will be discussed.

• Journal of the Korean Vacuum Society
• /
• v.9 no.4
• /
• pp.379-381
• /
• 2000

Organic materials have potential advantages to be utilized as semiconductors in field effect transistors and light emmiting diodes. Gold, Aluminium, Silver, Chromium and Indium are used by electrodes. Gold is ohmic contact and the others are schottky contact. In this study, Pentacene and various electrode materials were deposited by Organic Molecular Beam Deposition (OMBD) and vacuum evaporation respectively. Those films were photolithographically patterned for measurements. These devices showed no degration after a 15 days of storage in laboratory environment.