As a preliminary study to produce functional nanocomposites in a heat dissipation device, we performed the direct synthesis of carbon nanotubes (CNTs) on the surface of alumina (Al2O3) powders. A thermal chemical vapor deposition (TCVD) system was used to grow CNTs directly on the Al2O3 surface. In order to investigate the growth behavior of CNTs, we varied both furnace temperature of the TCVD ranging from 700 to 850 ℃ and concentration of the ferritin-dissolved DI solution from 0.1 to 2.0 mg/mL. From the previous results, the gas composition and duration time for CNT growth were fixed as C2H4 : H2 = 30 : 500 (vol. %) and 10 min, respectively. Based on the analysis results, the optimized growth temperature and ferritin concentration were found to be 825 ℃ and 0.5 mg/mL, respectively. The obtained results could be adopted to achieve mass production of nanocomposites with heat dissipation functionality.
Recently the non-destructive test technique which uses the grain boundary etching characteristics owing to the variation of material structures has been proposed. However, during in-serviced GEM test there are a lot of variables such as the changes of temperature and concentration of etching solution, the roughness condition of surface polished etc.. The purpose of this paper is to investigate the influences of these test variables on GEM test results in order to establish a reliable and sensitive of GEM evaluation technique. The experiments are conducted in various solution temperatures, 10$\^{C}$, 15$\^{C}$, 20$\^{C}$, and 25$\^{C}$ and in 70% and 100% concentrations of that, and in various surface roughnesses polished by #800, #2000, and 0.3㎛ alumina powder. Through the test with variables, it is verified that the decrease of temperature and concentration of etching solution and the coarsened surface roughness by not using polishing cloth and powder induce some badly and/or greatly influences on GEM test results like grain boundary etching width(W$\_$GB) and intersecting point ratio(N$\_$i/N$\_$0/). Therefore, to get reliable and good GEM test results, it must be prepared the surface of specimen polished by polishing cloth and 0.3㎛ alumina powder and the saturated picric acid solution having 25$\^{C}$ and be maintained the constant temperature(25$\^{C}$) during GEM test.
In this study, a process is developed for 3D printing with alumina ($Al_2O_3$). First, a photocurable slurry made from nanoparticle $Al_2O_3$ powder is mixed with hexanediol diacrylate binder and phenylbis(2,4,6-trimethylbenzoyl) phosphine oxide photoinitiator. The optimum solid content of $Al_2O_3$ is determined by measuring the rheological properties of the slurry. Then, green bodies of $Al_2O_3$ with different photoinitiator contents and UV exposure times are fabricated with a digital light processing (DLP) 3D printer. The dimensional accuracy of the printed $Al_2O_3$ green bodies and the number of defects are evaluated by carefully measuring the samples and imaging them with a scanning electron microscope. The optimum photoinitiator content and exposure time are 0.5 wt% and 0.8 s, respectively. These results show that $Al_2O_3$ products of various sizes and shapes can be fabricated by DLP 3D printing.
목적: 본 연구는 지르코니아 도재 표면의 나노구조 알루미나 코팅이 지르코니아와 레진 시멘트와의 전단결합강도에 미치는 영향을 알아보고자 하였다. 재료 및 방법: 지르코니아 원판 80개를 표면처리방법(산화알루미늄 분사처리(A), 산화알루미늄 분사 후 Rocatec 처리(R), 연마 후 나노구조 알루미나 코팅(PC), 산화알루미늄 분사 후 나노구조 알루미나 코팅(AC))에 따라 4개의 군으로 나누었다. 알루미나 코팅은 질산 알루미늄을 가수분해시킨 용액에 침적 후 $900^{\circ}C$에서 열처리 하여 시행하였다. 지르코니아 표면 코팅은 주사전자 현미경을 이용하여 관찰하였다. 레진 블럭을 레진 시멘트를 이용하여 각 실험군의 지르코니아 표면에 합착하고 열순환처리 전, 후의 전단결합강도를 측정하였다. 결과: 알루미나 코팅을 한 지르코니아 표면은 균일하고 치밀한 나노구조 알루미나가 관찰되었다. PC, AC 군은 열순환처리 전과 후 모두 A와 R 군에 비해 현저하게 높은 전단결합 강도를 보였다. A, R 군은 열순환처리 후에 급격한 결합강도의 감소를 보였으나, PC와 AC군은 열순환처리에 의해 유의할만한 결합강도의 감소를 보이지 않았다. 결론: 지르코니아 표면에 나노구조 알루미나 코팅처리하는 것은 레진시멘트와의 결합강도를 증가시키는 방법이다.
Monodispersed $Al_2O_3-TiO_2$ Powder was prepared by metal-alkoxide hydrolsis. A homogeneous nucleation/growth occurred in the solutions containing ethanol, butanol and acetonitrile, and resulted in spherical, submicrometer-sized powder. The titania and the alumina crystals were formed at $800^{\circ}C$ and $1000^{\circ}C$, respectively. These crystala were subsequently reacted each other beyond $1320^{\circ}C$ and formed $Al_2TiO_5$. The relative densities of sintered bodies prepared with as-received powder were examined at the temperature range of 1300-$1500^{\circ}C$ and they were about 79% at $1300^{\circ}C$. The formation of aluminum titanata decreased the relative density at the temperature range of 1300-$1450^{\circ}C$, and at above $1450^{\circ}C$, the relative density started to increase again. It was observed that $\alpha-Al_2O_3$-doped aluminum titanate was more stable than pure aluminum titante at $1200^{\circ}C$.
Dry gel composed of primary particles more homogeneous than starting boehmite powder was prepared by dispersing and gelling the boehmite powder. The transformation temperatures of boehmite powder, dry gel seeded with 0, 1, 3, 5 wt% $\alpha$-Al2O3, and ball milled gel were 1192$^{\circ}C$, 1184$^{\circ}C$, 1141$^{\circ}C$, 1119$^{\circ}C$, 1117$^{\circ}C$, and 1106$^{\circ}C$, respectively. Sintering behavior of dry gel without seed was similar to that of boehmite powder, but the sintered density of dry gel was improved as much as 10%~15% than boehmite powder. In the case of dry gel seeded with 5 wt% $\alpha$-Al2O3, sintering behavior was much improved. The relative density of the gel seeded with 5 wt% $\alpha$-Al2O3 was 96% when sintered at 140$0^{\circ}C$ for 1h. On the other hand, ball milling of the non-seeded sol for 48h resulted in the relative density of 97% when sintered at 130$0^{\circ}C$ for 1h. The size and amount of $\alpha$-Al2O3 particles added by ball milling were 0.107 ${\mu}{\textrm}{m}$ and 0.5 wt%.
After $SnO_2$ fine powder by precipitation method, Ca as crystallization inhibitor and Pd as catalyst were added to $SnO_2$ raw material by various methods. Thick film device was fabricated on the alumina substrate by mixing ethylene glycol and such mixed powders. The sensing characteristics of the device for methane gas were investigated. The most excellent gas sensing property was shown by the thick film device fabricated by Method 3 in which Ca and Pd doped $SnO_2$ powder is prepared by mixing $SnO_2$ powder, 0.1 wt% Ca acetate and 1 wt% $PdCl_2$ in deionized water and by calcining the mixture, after $Sn(OH)_4$ is dried at $110^{\circ}C$ for 36h. The sensitivity of the sensor fabricated with $SnO_2$-0.1 wt%Ca acetate-1wt%$PdCl_2$ powder heat-treated at $700^{\circ}C$ for 1h was about 86% for 5,000 ppm methane in air at $350^{\circ}C$ of the operating temperature. Response time and recovery were also excellent.
마이크로파 추출 및 하소 공정을 통하여 카올린으로부터 베타 알루미나 전구체 및 베타 알루미나 분말을 합성하였다. 황산 알루미늄 및 가성소다의 혼합 용액을 교반되는 에탄올 용액 중에 적하시켜서 $Al_2$(SO$_4$)$_3$.17$H_2O$ 및 $Na_2$SO$_4$.10$H_2O$의 균일한 침전물을 얻었다. $\beta$- 및 $\beta$\"-Al$_2$O$_3$상으로 구성된 베타 알루미나를 얻기 위하여 재래식 및 마이크로파 하소법으로 주어진 온도에서 약 2h 동안 침전물 시료를 하소하였다. 재래식 하소된 시료에 비하여 마이크로파 하소된 시료는 $\beta$\"-Al$_2$O$_3$상이 상대적으로 많이 존재하였다. 또한, 재래식 하소된 시료와 마이크로파 하소된 시료의 미세구조는 매우 상이하였다. 매우 상이하였다.
The powder characterization and sintering behavior of alkoxide-derived alumina powders prepared by esterification were investigated. The dried powders were calcined at 700$^{\circ}C$, 900$^{\circ}C$, 1080$^{\circ}C$, 1170$^{\circ}C$ for 1 h. and the resulting crystalline forms were amorphous, {{{{ gamma }} phase, {{{{ theta }}+{{{{ alpha }} phase, and {{{{ alpha }} phase, respectively. The sinterability was best in the case of being calcined at 1170$^{\circ}C$. It was most effective to disperse sintering additive in the initial stage from which acetate was formed. At 1600$^{\circ}C$ for 4 h, 98.5% of relative density was obtained when MgO and Fe2O3 were simultaneously doped, and dense sintered body whose density was near theoretical value was obtained when heating schedule was controlled.
질화 알루미늄을 AlO(OH)로부터 가장 낮은 온도에서 얻은 γ- alumina와 무수 염화 알루미늄 그리고 금속 알루미늄 분말을 출발물질로 하여 합성하는 연구를 하였다. 특히 반응온도에 주목하고 질화 알루미늄을 합성하였고 그 반응 조건들을 결정하였으며 그 결과에 대하여 논의하였다. 금속 알루미늄과 질소 가스의 반응은 비교적 낮은 온도에서 진행 되었고, 이 반응에 대한 반응 파라미터를 속도론적으로 연구하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.