• 한국세라믹학회지
• /
• 제20권3호
• /
• pp.199-204
• /
• 1983

An attempt was made to study wetting behavior of various low temperature molten frist on ceramic substrates including high alumina silicon carbide and porous fired clay plates by Sessile-drop method. The cosine values of contact angles between substrates and molten frist were linear as a function of temperature unless chemical reactions between substrate and molten frit occured. Addition of BaO to frit composition indicated that cosine of values of contact angles were gradually increased with increasing temperature but in the frist contained $Li_2O$ consine values were abruptly increased with increasing temperature after reached a certain temperature. The contact angle increased with increasing roughness of the substrate surface in case of alumina substrate plate.

• 한국세라믹학회지
• /
• 제36권5호
• /
• pp.497-503
• /
• 1999

Recently regenerative burner system was developed and begins to be gradually used for better energy savings. Compared to conventional burner system the regenrative one has the several merits such as higher fuel efficiency light weigh of apparatus low harmful toxic gas and homogeneous heating zone etc. The regenerative material a very important component of the new regenerative burner system should possess the properties of low specific density higher surface area and high specific heat capacity. Ceramics is the best regenerative material because of stable mechanical properties even at high temperature and better thermal properties and excellent chemical stability. In this study alumina ball alumina tube 3-D ceramic foam and hoeycomb as regenerative materials were tested and evaluated. The computer silumation was conducted and compared to the result of field test. This paper is aimed to introduce a new application of ceramics at high temperature.

• The Korean Journal of Ceramics
• /
• 제7권2호
• /
• pp.74-79
• /
• 2001

Alumina composite reinforced by chopped alumina fiber was fabricated by filter-pressing the fiber slurry followed by the infiltration of alumina slurry. The chopped fiber was coated with nickel by electroless plating method. The green samples were densified by hot-pressing. Microstructures were studied by SEM and the mechanical properties such as bending strength and fracture toughness were measured. The resulting mechanical properties were analyzed in relation with processing parameters such as preform density and resulting microstructures. The load-displacement curve of the specimen with Ni interlayer but without Ni inclusion showed brittle fracture mode due to the direct contact between matrix and fiber. The load-displacement curve of the specimen with Ni interlayer and Ni inclusion in the matrix which is introduced by high applied pressure during specimen preparation showed non-brittle fracture mode due to the fiber pull-out and dutile phases in the matrix.

• The Korean Journal of Ceramics
• /
• 제4권4호
• /
• pp.363-367
• /
• 1998

Alumina/mica and spinel/mica composites were fabricated by sintering of compacts containing 20 mass% fluoromica ($KMg_3AlSi_3O-{10}F_2$) glass and alumina or spinel. In both composites, mica precipitated as plate-like crystals at temperatures lower than $1300^{\circ}C$ and melted at $1300^{\circ}C$ to $1400^{\circ}C$. In alumina/mica composites, alumina and glass reacted to produce spinel, and the densification progressed by the solution-precipitation of alumina. Consequently, the glass composition changed and the mica did not precipitate at temperatures higher than $1400^{\circ}C$. However, mica precipitated after a reheating process. In spinel/mica composites, the glass composition did not change. After the mica phase melted, it recrystallized during slow cooling. The relative density reached the maximum at $1500^{\circ}C$ for alumina/mica and at $1300^{\circ}C$ spinel/mica composites, and decreased at further high temperatures.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2002년도 추계총회 및 연구발표회 초록집
• /
• pp.142.2-142
• /
• 2002

• 분석과학
• /
• 제6권2호
• /
• pp.225-229
• /
• 1993

알루미나 강화 지르코니아(10-30ATZ) 제조에 있어 지르코니아(TZ-2Y or TZ-0Y)와 알루미나(AKP-30) 분말 slurry에 2wt% 알루미나에 해당하는 알루미나졸을 첨가한 후 겔화시킴으로써 분말이 고르게 분산되어 있고, 동시에 알루미나겔이 분말의 표면을 코팅함으로써 응집이 일어나는 것을 막았다. 이렇게 제조된 ATZ는 $1450{\sim}1550^{\circ}C$ 이상에서 2시간 소결로 알루미나 grain이 $0.5{\mu}m$ 이하로 잘 분포되어 있는 좋은 미세구조와 이론 밀도의 99% 이상의 소결밀도를 보여 주었다. 또한 20ATZ 부근에서의 $K_{IC}$값은 ${\sim}8MPa{\cdot}m^{1/2}$으로 볼-밀링으로 얻는 $6MPa{\cdot}m^{1/2}$보다 높은 값을 보여주고 있다.

• 한국세라믹학회지
• /
• 제36권1호
• /
• pp.89-96
• /
• 1999

석고몰드의 단점을 극복할 수 있는 다공질 알루미나 몰드의 제조저건을 확립하였다. 다공질 알루미나 몰드의 제조를 위해 활성탄의 질량비에 따라 조성비를 달리하여 첨가한 후, ESA와 유동특성 등을 조하삼으로써 안정된 이상 슬러리를 제조하였으며, 이를 석고몰드에 캐스팅하여 얻은 원통형 알루미나 몰드를 사용하여 활성탄의 양과 소결온도에 따른 수축율 변화와 마모에 대한 저항성을 측정하였다. 다공질 알루미나 몰드의 소결에서는 비수축 소결구인 표면확산에 의해 입자간 넥 강도의 증진을 통한 몰드의 강도 증진을 도모하는 것이 바람직하며, 이를 위해 1,00$0^{\circ}C$이하에서 유지시간의 변화에 따른 열역학적 방법, 1,00$0^{\circ}C$이상의 온도에서 알루미나의 수축을 억제하면서 빠른 승온속도를 열처리온도에 따른 동역학적 방법과 이 두가지 방법을 혼합하는 방법 등으로 구분하여 다동질 알루미나 몰드의 소결조건을 분석하였다. 위 방법들에 대한 다공질 알루미나 몰드의 캐스팅 특성을 분석한 결과, 복합 소결법이 최적임을 알수 있었다. 제조된 다공질 알루미나 몰드의 비교적 높은 강도를 보였으며, 석고몰드레 비해 빠른 건조시간, 산, 염기에 대한 내식성 및 캐스팅 특성이 우수하였다.

• The Korean Journal of Ceramics
• /
• 제6권2호
• /
• pp.159-163
• /
• 2000

Alumina fibre has been synthesized successfully by sol-gel technique. Boehmite sol was prepared by hydrolyzing aluminium iso-propoxide and peptizing it with nitric acid. The stable sol thus obtained was used for fibre drawing when their viscosity reached the required value as a result of progress of the hydrolyzation and polycondensation reaction. The fibres dried at 11$0^{\circ}C$ for 12 hours were sintered at 1$600^{\circ}C$ for 5 hours. A reasonable sintered density with better microstructure and strength have been attained using 2 wt% of urea, magnesia and silica as sinter additives. Thermal analysis with sintering additives of 2 wt% and phase determination of the heat treated fibres using XRD and FT IR spectra confirms the phase transitions. The observation of surface and cross-section of the fibres were made using SEM. Fibres of uniform circular cross-section is obtained by fixing the shape in a setting solution.

• 한국세라믹학회지
• /
• 제46권3호
• /
• pp.295-300
• /
• 2009

The crystal structure of surface coatings on Al1050 alloy by PEO (Plasma Electrolytic Oxidation), were investigated. The electrolyte for PEO was Na-Si-P system solution. The main crystalline phase were $\gamma$-alumina and $\alpha$-alumina. Crystallinity was increased with applied voltage and applied time. The dominant crystalline phase were affected not only chemical composition of Al alloy substrate and electrolyte, but also the +/- ratio of applied voltage.

• 대한기계학회논문집A
• /
• 제21권1호
• /
• pp.73-82
• /
• 1997

High temperature densification behaviors of alumina powder compacts were investigated under hot pressing and hot isostatic pressing. An alumina part of valve-head shape was fabricated under hot pressing and its forming process was simulated by finite element calculation. an alumina powder compact encapsulated by a stainless steel container was also densified under hot isostatic pressing. Inhomogeneous deformations during hot isostatic pressing due to the canning effect were observed experimentally and predicted by finite element analysis.