• Proceedings of the KIEE Conference
• /
• 1989.11a
• /
• pp.53-57
• /
• 1989

Until now, method of equivalent circuit is generally used in analyzing the characteristic of the synchronous alternator. But this method can't apply when loads are connected to alternator. In this paper, we analyzed the load characteristic of the synchronous alternator with permanant magnet using 2-dimensional finite element method having voltage source. The loads of a alternator are battary and diodes which are used to rectify. also, we used half periodic boundary condition in the F.E.M calculation

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.36 no.4
• /
• pp.92-99
• /
• 2013

Many automotive components for power generation such as motors and alternators have been widely using ferrite magnets. To ensure a high level of efficiency could be achieved in an alternator, the assembled magnets must be in good enough durability. Recently, some hairline cracks have been found on the magnet produced by manufacturers in Korea. Thus, there is an increasing concern that some of the magnets produced could cause further problems after being assembled in the alternator. Based on the standard alternator test (RS0008 : 2006), this paper has developed an accelerated failure-free test for magnets in alternator to demonstrate that assembled magnets will meet durability objective specified by the manufacturer. This guarantees the target life of the magnet with 90 percent reliability and 90 percent confidence level (R90C90). Temperature and rotation speed were selected as accelerated stress factors.

• Journal of Power Electronics
• /
• v.12 no.1
• /
• pp.49-57
• /
• 2012

This paper presents performance evaluation of an Integrated Starter-Alternator (ISA) prototype with an Interior Permanent Magnet (IPM) synchronous machine under sensor-less operation. To attain a high starting torque at zero speed and in subsequent extremely low speed range, a hybrid signal injection method is proposed. At higher speed, an improved stator flux observer is used for the stator flux estimation. This observer is able to produce accurately-estimated stator flux linkage for high performance Direct Torque and Flux Control (DTFC) implementation. The sensor-less DTFC IPM synchronous machine drive takes full advantage of the capacity of the power converter and fulfills the control specifications for the ISA. The trajectory control algorithm responds rapidly and in a well behaved manner over a wide range of operating conditions. The experimental results verify the feasibility and advantages of the system.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.1
• /
• pp.114-120
• /
• 2016

This paper describes generating efficiency characteristics of the double acting Stirling engine/generator for domestic small-scale CHP (Combined Heat and Power) system. In small distributed generation applications, Stirling engine has competition from fuel cell, microturbine and etc. In order to be economical in the applications, a long life with minimum maintenance is generally required. Free piston Stirling engine (FPSE) has no crank and rotating parts to generate lateral forces and require lubrication. Double acting Stirling engine/generator has one displacer and two power piston which are supported by flexure springs. Two power pistons oscillate with symmetric displacement and are connected with moving magnet type linear generators for power generation from PV work. In experiments, 1 kW class double acting free piston Stirling engine/generator is fabricated and tested. Heat is supplied to hot end of engine by the combustion of natural gas and converted to electric power by linear generators which are assembled with power pistons. The electric parameters such as voltage, current and phase are measured with for variable flow rate of fuel gas. Especially, generating efficiency of FPSE is measured with three different measurement methods. Generating efficiency of the double acting Stirling engine/alternator is about 24%.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.9
• /
• pp.914-921
• /
• 2014

In this paper, an algorithm is suggested to detect an offset angle of the absolute rotor position sensor after the initial assembly of a PMSG. Unlike previous studies in a stationary state, this one is not designed to detect an electrical angle but rather the absolute position of the rotor is detected while operating the generator. Also,a position sensor, current sensors and voltage sensor were used to ensure reliability. This technique completes the detection of the sensor offset in two steps. In the first step, a zero-crossing of the EMF is measured using a voltage sensor to detect the electrical angle offset when the alternator is actuated by the engine. In the second step, a high frequency current is injected along the d-axis on-line during the control of the generation, eventually to obtain the inductance using a DFT (Discrete Fourier Transform), and then to ultimately extract the final electrical angle offset through the comparison of the inductance magnitude. The suggested algorithm was validated with PSIM simulation and, furthermore, was tested with actual experiments on a dynamometer.

• Transactions of the Korean hydrogen and new energy society
• /
• v.26 no.6
• /
• pp.638-644
• /
• 2015

This paper describes the continuing effort to analysis and design on dynamic and electrical behavior of gamma-type free piston Stirling engine/generator with dual-opposed linear generator for domestic micro-CHP (Combined Heat and Power) system. The double acting Stirling engine/generator has one displacer and two power piston which are supported by flexure springs. Two power pistons oscillate with symmetric sinusoidal displacement and are connected with moving magnet type linear generators for power generation. To operate Stirling engine/generator, combustion heat of natural gas is supplied to hot-end and heat is rejected from cold-end by cooling water. The temperature difference across the displacer induces the oscillating motion, and it can be explained with mass-spring vibration system. The purpose of this paper is to describe the design process of linear generator for the double acting free-piston Stirling engine.