• 한국자동차공학회논문집
• /
• 제16권5호
• /
• pp.147-156
• /
• 2008

As the management of fuel efficiency becomes globally reinforced in attempts to find an environment-friendly vehicle that will operate against global warming, the interest in and the demand for the type of vehicle with a high-efficiency diesel engine using light oil. However, it also emits a greater amount of PM (particulate matter) and NOx than emissions from vehicles using other types of fuels. Therefore, the DME (Dimethyl Ether), an oxygen containing fuel draws attention as an alternative fuel for light oil that can be used for diesel engines since it generates very little smoke. But to develop and compare performance of an electric controlled common-rail DME engine, engine tests requires optimized injection conditions at required engine RPM and engine torque. These injection conditions cannot be set freely and the data configuration through the experimentally repeated application requires much time as well as a significant amount of errors and effort. The object of this study is to configure the basic injection map using the results of the DME engine experiments performed so far. For this, in this study, the functionalization of the required equations were performed along with the basic review of the factors that had influence on the data map. Through this, the information on the injection pressure, injection amount, injection duration, injection timing, etc. under certain operation condition could be obtained.

• 한국자동차공학회논문집
• /
• 제17권4호
• /
• pp.32-39
• /
• 2009

The HCCI engine is a next generation engine, with high efficiency and low emissions. The engine may be an alternative to SI and DI engines; however, HCCI's operating range is limited by an excessive rate of pressure rise during combustion and the resulting engine knock in high-load. The purpose of this study was to gain a understanding of the effect of only initial temperature and thermal stratification for reducing the pressure-rise rate in HCCI combustion. And we confirmed characteristics of combustion, knocking and emissions. The engine was fueled with Di-Methyl Ether. The computations were conducted using both a single-zone model and a multi-zone model by CHEMKIN and modified SENKIN.

• 오토저널
• /
• 제14권3호
• /
• pp.71-79
• /
• 1992

Recently, air pollution and energy security problems have necessitated the development of alternative fuel vehicles. As an alternative fuel vehicle FFV(Flexible Fuel Vehicle) which can be operated by and mixture between gasoline and M85(methanol 85% and gasoline 15% by vol. percent) has been drawing great attention. But poor cold startability of high methanol- content fuel which is characteristic of lower fuel volatility and higher latent heat of vaporization than gasoline is one of the major problems to be solved for the development of FFV. In this paper, important factors influencing cold startability of general S.I. engines are described. And, so-me cost-effective and practical methods were investigated in view of the optimization of fuel-ing parameters and ignition system for M85 fuel. The test results showed good startability up to (-22)-(-23).deg.C.

• 한국자동차공학회논문집
• /
• 제21권6호
• /
• pp.155-165
• /
• 2013

The effect of gaseous ammonia direct injection on the engine performance and exhaust emissions in gasoline-ammonia dual fueled spark-ignition engine was investigated in this study. Results show that based on the gasoline contribution engine power increases as the ammonia injection timing and duration is advanced and increased, respectively. However, as the initial amount of gasoline is increased the maximum power output contribution from ammonia is reduced. For gasoline-ammonia, the appropriate injection timing is found to range from 320 BTDC at low loads to 370 BTDC at high loads and the peak pressures are slightly lower than that for gasoline due to the slow flame speed of ammonia, resulting in the reduction of combustion efficiency. The brake specific energy consumption (BSEC) for gasoline-ammonia has little difference compared to the BSEC for gasoline only. Ammonia direct injection causes slight reduction of $CO_2$ and CO for all presented loads but significantly increases HC due to the low combustion efficiency of ammonia. Also, ammonia direct injection results in both increased ammonia and NOx in the exhaust due to formation of fuel NOx and ammonia slip.

• International Journal of Automotive Technology
• /
• 제8권4호
• /
• pp.421-428
• /
• 2007

This paper investigates the combustion and emission characteristics of a compression ignition engine fueled with neat and blended Shell's gas-to-liquid (GTL) fuel, which was derived from natural gas through the Fischer-Tropsch process. The experiments were conducted in a 6-cylinder DI diesel engine with pump timing settings of $6^{\circ},\;9^{\circ}\;and\;12^{\circ}$crank angle before TDC over ECE R49 and US 13-mode cycles separately and compared to a conventional diesel fuel. The results show that GTL exhibited almost the same power and torque output, improved fuel economy and effective thermal efficiency. It was found that GTL displayed lower peak in-cylinder combustion pressure and maximum heat release rate (HRR), the timings of the peak pressure and the maximum HRR were generally delayed, and the combustion durations were almost equivalent for diesel and GTL under the same speed-load condition. The results also indicate that, compared to diesel fuel, GTL blends showed a trend forward decreasing four regulated emissions simultaneously and a higher GTL fraction in blends contributing to further reductions in the emissions. In particular and on average, neat GTL significantly reduced HC, CO, NOx and PM by 16.4%, 17.8%, 18.3% and 32.4%, respectively, for all cases.

• 한국가스학회지
• /
• 제15권2호
• /
• pp.63-68
• /
• 2011

합성가스는 Biomass, 석탄, 폐기물 등의 가스화 공정을 통해 얻을 수 있는 대표적인 대체연료로 저발열량에도 불구하고 수소가 포함되어 있기 때문에 이를 엔진에 적용하여 에너지를 생산하고자 하는 노력이 계속되어 왔다. 하지만 연료 조성 측면에서 합성가스는 가스화 원료의 종류에 따라 합성가스 내의 수소 함유량이 달라지는데, 이러한 함량 변화는 수소의 좋은 연소특성으로 인해 엔진 성능에 큰 영향을 미칠 수 있기 때문에 이에 대한 연구가 필요한 실정이다. 따라서 이번 연구에서는 다양한 수소 분율을 갖는 합성가스를 동일 발열량 및 유량 조건에서 모사하고 이를 이용하여 연료 내 수소 비율(vol %)이 연소특성에 주는 영향을 파악하였다. 실험 결과로 각 수소 함량에 따른 최적 점화시기를 결정하였으며, 수소 비율의 변화가 연소특성, 엔진 출력, 효율, 배기 성능에 미치는 영향을 제시하였다.

• 한국가스학회지
• /
• 제27권3호
• /
• pp.91-97
• /
• 2023

오래된 디젤 엔진을 탑재하고 있는 노후화된 건설용 기계 및 차량들은 보통 수명이 길기 때문에 최신의 배기 규제와는 동떨어진 수준의 유해한 배출가스를 계속 배출하고 있다. 따라서 이러한 구형 디젤 엔진을 최신 배기 규제를 만족하는 엔진으로 대체할 수 있다면 대기질 개선에 도움이 될 것으로 기대되는데, 건설 현장에서 손쉽게 구할 수 있는 프로판 연료를 적용한 엔진이 적합한 대안이 될 수 있다. 따라서 본 연구에서는 6.8리터 CNG 엔진을 베이스로 프로판 전용 엔진을 개발하였으며, 가스 전용 인젝터, 배기가스재순환(EGR), 강화된 촉매 등의 기술이 적용되었다. 그 결과 동급의 디젤 엔진 출력 및 토크를 확보하는 한편 최신 배출가스 규제인 Stage-V 수준에서 질소산화물은 절반 수준에 해당하는 배출가스 성능을 달성하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.220.2-220.2
• /
• 2011

Biodiesel and biodiesel blend fuel are receiving increasing attention as alternative fuels for diesel engines without substantial modifications. Biodiesel fuels and blending have been widely studied and applied in diesel engine because of biodiesel's lower sulfur, lower aromatic hydrocarbon and higher oxygen content. Biodiesels have the potential to be oxidized in different condition. It has reported that oxidation deterioration of biodiesel is different in the condition of storage and oxidation causes chemical property change of methyl esters. Sunlight intensity, temperature, material of container and contact surface with oxygen are key dominant factors accelerating oxidation deterioration. In this study, we chose temperature among key oxidation conditions and metal container filled with biodiesel was heated at about $110^{\circ}C$ for 10 days in order to accelerate oxidation deterioration. To better understand the effect of biodiesel blends on emission, steady state tests were conducted on a heavy duty diesel engine. The engine was fueled with Ultra Low Sulphur Diesel(ULSD), a blend of 10% and 20%(BD10, BD20) on volumetric basis, equipped with a common rail direct injection system and turbocharger, lives up to the requirements of EURO 3. The experimental results show that the blend fuel of normal biodiesel with BD10 and BD20 increased NOx. The result of PM was similar to diesel fuel on BD10, but the result of PM on BD20 was increased about 63% more than its of diesel. The blend fuel of Oxidation biodiesel with BD10 and BD20 increased NOx as the results of normal biodiesel. But PM was all increased on BD10 and BD20. Especially THC was extremely increased when test fuel contains biodiesel about 140% more than its of diesel. Through this study, we knew that oxidation deterioration of biodiesel affects emission of diesel engine.

• 한국자동차공학회논문집
• /
• 제25권3호
• /
• pp.380-388
• /
• 2017

Wood pyrolysis oil(WPO) has been regarded as an alternative fuel for diesel engines. However, WPO is not feasible for use directly in diesel engines due to its poor fuel quality such as low energy density, high acidity, high viscosity and low cetane number. The most widely used approach to improve WPO fuel quality is to blend WPO with other hydrocarbon fuels that have a higher cetane number. However, WPO and fossil fuels are not usually blended because of their different polarity. Also, clogging and polymerization problems in the fuel supply system can occur when the engine is operated with WPO. Polymerization can be prevented by diluting WPO with other alcohol fuels. However, WPO-alcohol blended fuel does not produce self-ignition. Therefore, additional cetane enhancement to the blended fuel is required to enhance auto-ignitability. In this study, WPO was blended with n-butanol and two cetane enhancements(PEG 400 and 2-EHN) for application to a diesel generator. Experimental results showed that the WPO-butanol blended fuel achieved a very stable engine operation under maximum WPO content of 20 wt%.

• 대한기계학회논문집B
• /
• 제39권7호
• /
• pp.609-615
• /
• 2015

본 연구는 직접분사식 가솔린엔진에서 공기 과잉률 및 바이오에탄올-가솔린 혼합연료의 혼합비에 따른 연소특성과 배기배출물 특성을 실험적으로 규명한 것이다. 다양한 공기 과잉률 및 혼합비 조건에서 실험을 수행하였으며, 연소실 압력, 열발생률, 연료소비율 등을 통해 연소특성을 분석하였으며, 배기배출물 특성은 미연탄화수소(HC), 일산화탄소(CO), 질소산화물($NO_x$) 분석을 통해 확인하였다. 혼합연료의 실험결과는 100% 가솔린 및 바이오에탄올 실험결과와 비교하였다. 실험결과 최고연소압력과 열발생률, 제동연료소비율은 혼합비의 증가에 따라 증가하였으며, CO, HC, $NO_x$와 같은 배기배출물은 바이오 에탄올 혼합비율이 증가함에 따라 감소하였다. 혼합연료의 배기배출물 수준은 가솔린 보다 낮게 나타났다.