• 한국표면공학회지
• /
• 제29권3호
• /
• pp.195-202
• /
• 1996

The composition, the microstructure and the magnetic properties(HC and Hk) of Fe-Co-Ni alloy electrodeposits were investigated according to the electrolysis conditions using sulfate bath paddle agitated. The current efficiency of the alloys electrodeposition was considerably low in the range of 16∼50%. The Fe content(wt.%) of the alloy increased from 20% to 57% with current density, while Ni content of them decreased in the range of 70∼24% respectively, and Co content was nearly constant. As a result, Fe/Ni ratio of the alloy increased from 0.3 to 2.0 showing the anomalous codeposition. The structure of the alloy changed from fcc to the mixed one of fcc+bcc with the increase of Fe/Ni ratio. The preferred orientation of the alloy with fcc and bcc structure were (220) and (110) respectively. The alloy with Fe/Ni ratio(0.3∼l.2) had the lowest coercivity of 0.4∼0.8 Oe.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.194-195
• /
• 2005

(100-x)Zn xMg alloy films are prepared onto cold-rolled steel substrates; where x ranged from 0 to about 38 atomic %. The alloy films show microcrystalline and grain structures respectively, according to preparation conditions such as composition ratio of zinc and magnesium or gas pressures etc.. And X-ray diffraction analysis indicates not only the presence of Zn-Mg thin films with forced solid solution but also the one of $MgZn_2$ alloy films partly. In addition the influence of Mg/Zn composition ratio and morphology of the Zn-Mg alloy films on corrosion behavior is evaluated by electro-chemical anodic polarization tests in deaerated 3% NaCl solution. From this experimental results, all the prepared Zn-Mg alloy films showed obviously good corrosion resistance to compare with 99.99% Zn and 99.99% Mg Ingots for evaporation metal. It is thought that the Zn-Mg films with effective forced solid solution prepared by plasma enhanced PVD method, produces smaller and denser grain structure so that may improve the formation of homogeneous passive layer in corrosion environment.

• 한국표면공학회지
• /
• 제41권3호
• /
• pp.109-113
• /
• 2008

High strength 7xxx series Al-Zn-Mg alloy have been investigated for using light weight automotive parts especially for bump back beam. The composition of commercial 7xxx aluminum has the Zn/Mg ratio about 3 and Cu over 2 wt%, but this composition isn't adequate for appling to automotive bump back beam due to its high resistance to extrusion and bad weldability. In this study the Zn/Mg ratio was increased for better extrusion and Cu content was reduced for better welding. With this new composition we investigated the effect of composition on the resistivity against stress corrosion cracking. As the Zn/Mg ratio is increased fracture energy obtained by slow strain rate test was decreased, which means degradation of SCC resistance. While the fracture energy was increased with Cu contents although it is below 1%, which means improvement of SCC resistance. These effects of composition change on the SCC resistivity were identified by observing the fracture surface and crack propagation.

• 대한치과기공학회지
• /
• 제35권2호
• /
• pp.113-120
• /
• 2013

Purpose: This study was to observe surface property and bonding strength according to composition of Ni-Cr alloy for porcelain fused to metal crown. The two kinds of Ni-Cr alloy with different composition ratio of parent metal were observed general properties and chemical properties of each alloy surface and measured the shear bonding strength between ceramic and each alloys. The aim of study was to suggest the material for design of parent metal's composition ratio to development of alloy for porcelain fused to metal crown. Methods: The two kinds of alloy as test specimen was Ni(71wt.%)-Cr(12wt.%) and Ni(63wt.%)-Cr(23wt.%) alloy. The oxide on surface was observed by SEM and EDX. And the shear test was performed by MTS. Results: The surface property and oxide characteristic analysis of oxide layer, weight percentage of Element O within $Ni_{71}Cr_{12}$ alloy measured 12.74wt.%, but $Ni_{63}Cr_{23}$ alloy was measured 15.91wt.%. And the maximum shear bonding strength was measured 106.14MPa between $Ni_{71}Cr_{12}$ alloy and vintage halo (VV group). Conclusion: The surface property and oxide characteristic of $Ni_{71}Cr_{12}$ alloy was similar to $Ni_{63}Cr_{23}$ alloy. And VV group has the strongest shear bonding strength.

• 한국표면공학회지
• /
• 제35권4호
• /
• pp.232-240
• /
• 2002

The composition and the microstructure of the Zn-Cr alloys electroplated in chloride bath with EDTA were studied according to electrolysis conditions. The cathode current efficiency decreased with increasing both Cr/(Cr+Zn) ratio and current density. The Cr content of the alloy deposits increased with Cr/(Cr+Zn) ratio and current density The phase structure of Zn-Cr alloy deposits changed from η-Zn through η-Zn+${\gamma}$'-ZnCr to ${\gamma}$'-ZnCr with increasing Cr content of alloys. The surface morphology of Zn-Cr alloy deposits changed from fine needle shaped crystallites through the mixed structure of needle-shaped and granular one to the colony structure with fine granular crystallites according to the change of phase structure

• 대한치과기공학회지
• /
• 제35권4호
• /
• pp.359-364
• /
• 2013

Purpose: This study was to observe characteristic of metal oxidation and bonding strength according to composition of Ni-Cr alloy for porcelain fused to metal crown. The three kinds of Ni-Cr alloy with different composition ratio of parent metal were observed general properties and chemical properties of each alloy surface and measured the shear bonding strength between ceramic and each alloys. The aim of study was to suggest the material for design of parent metal's composition ratio to development of alloy for porcelain fused to metal crown. Methods: The three kinds of alloy as test specimen was Ni(59wt%)-Cr(24wt%), Ni(67wt.%)-Cr(16wt.%) alloy and Ni(71wt%)-Cr(12wt%)alloy. The oxide on surface was observed by EDX. And the shear test was performed by MTS. Results: The surface property and oxide characteristic analysis of oxide layer, weight percentage of Element O within $Ni_{59}Cr_{24}$ alloy measured 23.03wt%, $Ni_{67}Cr_{16}$ alloy measured 21.13wt% and $Ni_{71}Cr_{12}$ alloy was measured 48.55wt%. And the maximum shear bonding strength was measured 58.02Mpa between $Ni_{59}Cr_{24}$ alloy and vintage halo(H2 group). Conclusion: The surface property and oxide characteristic three kind of Ni-Cr alloy was similar. and shear bonding strength showed the highest bonding strength in H2 specimens.

• 대한치과기공학회지
• /
• 제34권4호
• /
• pp.361-368
• /
• 2012

Purpose: The aim of this study was to analysis the composition on the centrifugal casting and the oxide on the casting temperature. Methods: The nickel based alloy were used in this study. Wax pattern specimens (10*10*2) were invested with phosphate-bonded investment in metal rings, the liquid/powder ratio and overall burn-out schedules for these investments were followed in accordance with the manufacturer's instructions. After casting, the alloy specimens were evaluated as regards composition(EPMA). The casting temperatures were as follows: $1400^{\circ}C$ and $1700^{\circ}C$. The quantitative analysis of oxides were scanning electron microscope(SEM), energy dispersive spectroscopy(EDS) and line scanning. Results: Nearer the injection lines showed that there is a large amount of nickel. Quantitative of oxides of Ni-Cr alloy cast from $1400^{\circ}C$ is lager than Ni-Cr alloy cast from $1700^{\circ}C$. Conclusion: Casting when using a centrifugal casting machine centrifugal force affects the composition of the alloy. The higher the temperature, the amount of oxide that is generated many.

• 헤리티지:역사와 과학
• /
• 제57권1호
• /
• pp.146-159
• /
• 2024

본 연구에서는 강진 고성사 청동보살좌상을 대상으로 과학적 분석을 통해 불상의 제작기술 및 납 원료산지에 대한 연구를 실시하였다. 불상에서 수습한 극미량의 시료를 대상으로 미세조직 관찰결과 주조 공정을 통해 제작되었음을 알 수 있었다. 이어 SEM-EDS를 통한 합금조성비 분석결과 구리(Cu) 81.26wt% 주석(Sn) 16.42wt%, 납(Pb) 1.72wt%의 삼원계 합금으로 확인되었다. 열이온화질량분석기(TIMS)를 이용한 납동위원소비 분석결과를 한반도 납동위원소비 분포도에 대입한 결과 전라도와 충청도 지역, 경상남·북도 지역에 도시되었다. 불상이 봉안된 강진 고성사는 해당영역의 사이에 위치하고 있다. 이러한 과학적 분석결과를 종합해 볼 때 강진 고성사 청동보살좌상은 구리, 주석, 납을 합금하여 주조하였으며, 불상제작 시 사용된 납 원료는 고성사 인근 지역에서 수급하여 사용한 것으로 판단된다. 이때 주목할 점은 해당 불상이 높이 51cm의 중·대형 불상임에도 불구하고 합금조성비 분석결과 기존 선행연구에서 제시한 소형 청동 및 금동제 불상의 납 함량비와 유사한 경향성을 보이고 있다는 것이다. 이에 불상의 크기와 납 함량비 간의 연관성을 고찰하고자 고성사 청동보살좌상과 조성연대가 유사한 청동 및 금동제 불상의 형태학적 특징 및 합금조성비 등 전반적인 제작기술을 비교분석 하였다. 비교결과 청동 및 금동제 불상의 합금조성비를 결정하는 요인에는 불상의 크기 뿐만 아니라 양식적인 특징, 조성연대 등 다양한 요인이 존재할 수 있으며, 이에 따라 불상을 조성할 당시 합금조성비 또는 주조기술을 적절히 조절하였을 가능성을 확인하였다. 즉, 불상의 제작기술 연구를 위해서는 방사선 투과촬영조사 등을 활용한 내부구조 관찰, 미세조직관찰 및 합금조성비 분석 등의 과학적 분석결과 뿐만 아니라 양식적 특징 및 조성연대에 관한 고고·미술사학적 연구를 함께 진행함으로서 보다 종합적인 불상 제작기술체계에 대한 규명이 이루어져야 할 것으로 판단된다.

• 한국표면공학회지
• /
• 제45권3호
• /
• pp.136-141
• /
• 2012

'Jikjisimcheyocheal (Jikji afterwards)' is known as a first book printed by the metal type in the world. The metal type used for printing this book has not been found yet. To help for replicating the original metal type, it is required to investigate the composition analysis of the copied metal type. In this study, the composition analysis and thermodynamic care for replicating of ancient metal type was performed on the basis of an analytical reports concerned with the ancient metal type which made after Jikji printing. Metal types were made by remelting and casting of the mother alloy which came from a cast of a mixed metals in accordance with the composition revealed in the literatures. Change of composition during remelting of mother alloy and casting of metal was detected by the EDS analysis. The reasons for variation in composition were discussed by metallurgical and thermodynamic point of view, and a mixing ratio of metals to get the original composition of ancient metal type is suggested. Some attention should be paid on mixing, melting and casting of metals to get an objected composition for copy of ancient metal type.

• 한국주조공학회지
• /
• 제29권6호
• /
• pp.270-276
• /
• 2009

After casting button-type small ingots of ternary Fe-Mn-S alloys which had three different Mn/S ratios (1, 5 and 70) in a vacuum arc furnace, the effect of the ratio on the sulfide formation was investigated. In case of the Mn/S ratio of 1, if alloy composition was located in an iron-rich corner on a Fe-Mn-S ternary phase diagram, only duplex MnS-FeS sulfide films were observed in the grain boundary. If the alloy composition was located in the miscibility gap area of the phase diagram, primary globular dendritic sulfides and dendritic sulfide slags were generated within the grain and tubular monotectic sulfides were also detected in the grain boundary. When the Mn/S ratio was 5, if the alloy composition was in the iron-rich corner, only bead-like sulfides were generated. On the other hand, if the composition was in the miscibility gap area, globular dendritic sulfides and dendritic sulfide slags were generated in the form of primary sulfide inclusions and rod-like eutectic sulfides were observed in the grain boundary. Especially, if the contents of Mn and S increased more in the miscibility gap area of the phase diagram, primary globular sulfides containing iron intrusions were observed. In case of Mn/S ratio of 70, if the contents of Mn and S was decreased in the Fe corner of the phase diagram, only bead-like sulfides were observed in the grain boundary. Despite the composition was outside the miscibility gap area of the phase diagram, if the contents of Mn and S increased, clusters of fine sulfide particles as well as fine spherical primary monophase sulfides were observed in the grain boundary.