• 한국자기학회지
• /
• 제8권3호
• /
• pp.156-160
• /
• 1998

고주파 마그네트론 스퍼링법에 의하여 두께 약 2000$\AA$으로 제조한 (Mn0.5-ZSb0.5+Z)100-yPty(0$0^{\circ}C$의 진공중에서 열처리한 후, X-선회질장치, 토크자려계, kerr 효과 즉정장치를 이용하여 결정구조 및 자기광학적 특성을 조사하였다. 열처리 후, MnSbPt 합금막은 FDD의 Clb-형구조를 갖으나, MnSbAg 합금막은 HCP의 NiAs-형구조를 갖고 c-축이 막면에 수직하여 배향하는 이방성조직이 형성되나 열처리시간이 길어지면 등방성조직으로 바뀐다. 30$0^{\circ}C$에서 3시간 동안 dufcjflgksMnSbAg 합금막에서 우수한 수직자기이방성이 관측되었으며 Mn47.4Sb47.5Ag5.1 합금막으로부터 K1=6.6$\times$105 erg/cm3, K2=1.9$\times$105 erg/cm3의 수직자기이방성값을 얻었다. 입사파장 700~100nm 범위에서 MnSbpt 합금막의 Kerr 회전각은 입사파장이 감소할수록 증가하나 MnSgAg 합금막은 반대경향을 보인다. 입사파장 λ=700nm에서 Mn41.1Sb44.9Pt14.0 및 Mn47.4Sb47.5Pt5.1 합금막의 Kerr 회전각 $\theta$k는 각각 1.7$^{\circ}$와 0.2$^{\circ}$이고 λ=1000nm에서는 각각 0.6$^{\circ}$와 0.97$^{\circ}$이다.

• 한국표면공학회지
• /
• 제47권6호
• /
• pp.282-286
• /
• 2014

Wear characteristic of the nitrided SKD61 which is a typical mold material using for the extrusion of Al6061 alloy was investigated. The surface of SKD61 was nitrided by salt bath and plasma processes. The thickness of surface nitride layer was about $8.9{\mu}m{\sim}21.3{\mu}m$. Reciprocating friction wear test conducted using pin on disk type indicated the plasma treatment followed salt bath has a lower friction coefficient and a smaller adhesive wear with Al6061 alloy. That was identified by the $Fe_4N$ which has a better wear resistance than FeN mainly formed by plasma nitriding.

• 열처리공학회지
• /
• 제21권6호
• /
• pp.293-299
• /
• 2008

In order to provide with fundamental data of the wrought Mg alloy for press forging, the effect of annealing temperature on the microstructure, texture development and tensile properties is studied in a commercial AZ31B Mg alloy sheet. Basal texture i.e. $(0001){\pm}5^{\circ}$[21$\bar{3}$0] is developed in a commercial AZ31B Mg sheet, and the texture is not changed considerably by annealing over $400^{\circ}C{\times}30min$, while (10$\bar{3}$0) component with high intensity can be observed due to abnormal grain growth. When the sheet is tensile-deformed with RD, $45^{\circ}$ and TD directions at room temperature, fracture strains are given by 25.8, 21.4 and 11.9% in the order of RD, $45^{\circ}$ and TD directions, respectively. With increasing annealing temperature up to $450^{\circ}C{\times}30min$, little change in mean grain size can be revealed by annealing below $300^{\circ}C{\times}30min$ but an abnormal grain growth, where some grains become significantly coarser than the rest, occurs by annealing above $400^{\circ}C{\times}30min$. The maximum tensile strain of around 25% is obtained by annealing below $300^{\circ}C{\times}30min$, but it is abruptly decreased to 16% by annealing above $400^{\circ}C{\times}30min$ owing to intergranular fracture of abnormal grown grains.

• 한국자기학회지
• /
• 제4권3호
• /
• pp.244-248
• /
• 1994

NdTbFeCo 합금막 및 NdTbFeCo/TbFeCo 이층막에 대한 자기광학 Kerr 회전각(${\theta}_{k}$)의 파장의존성 및 자기적 특성을 조사하였다. FeCo의 조성을 일정하게 유지하고 NdTbFeCo 합금막에서 Tb의 일부를 Nd로 치환한 결과, Nd 조성이 증가할 수록 400 nm의 파장영역에서 ${\theta}_{k}$는 증대되었으나, 보자력과 각형비가 급격히 감소하였다. NdTbFeCo 막이 단파장에서 큰 ${\theta}_{k}$를 나타냄에도 불구하고 보자력이 작아 단파장용 광자기기록 매체로서 응용가능성이 희박할 것으로 생각되어, 보자력이 큰 TbFeCo 막과 교환결합 이층막을 제작하였다. 제작된 시료중 $Nd_{16.9}Tb_{15.2}Fe_{50.4}Co_{17.5}(150\;{\AA})/Tb_{21.1}Fe_{65.0}Co_{13.9}(300\;{\AA})$ 교환결합 이층막이 6.0 KOe의 보자력과 500 nm에서 $0.32^{\circ}$의 ${\theta}_{k}$를 나타내었다.

• 한국기계가공학회지
• /
• 제11권6호
• /
• pp.16-21
• /
• 2012

Magnesium alloy has been focussed as lightweight material owing to its high strength even though low density with aluminum alloy, titanium alloy and plastic material. Friction stir welding technique was performed by rotating and plunging a shouldered tool with a small diameter pin into the joint line between two butted plates and useful to join magnesium alloy. In this paper, the experiments of friction stir welding were done to investigate the joint characteristics of AZ31 magnesium alloy. For its evaluation, the orthogonal array method$(L_{27}(3^{13}))$ was applied with four factors of pin diameter, shoulder diameter, travel speed and rotation speed of tool and also three levels of each factor. Nine tools were worked through shoulder diameter of 9, 12, 15mm and pin root diameter of 3, 4, 5mm. In addition tensile tests were excuted for the assessment of mechanical properties for joint conditions. From the results, pin diameter, shoulder diameter, and rotating speed of tool influenced on the tensile strength meaningful, but welding speed did not influence on that by the variance analysis. Beside of that, optimum condition of tensile strength was estimated as following ; shoulder diameter:15mm, welding speed:200mm/min, rotating speed:200rpm.

• 한국안전학회지
• /
• 제22권2호
• /
• pp.15-21
• /
• 2007

Fine grained Al-5083 alloy produced by equal channel angular pressing (ECAP) at $120^{\circ}C$ was tested for investigating mechanical properties and crack growth propagation behavior. Also, FEM stress and strain analysis for the samples during ECAP were investigated, using a plastic deformation analysis software DEFORM 2-D. Coarse grained as-received samples exhibited UTS of 255.6MPa with a elongation to failure of 34.4%. By contrast, the ECAPed fine grained samples exhibited UTS of 362.0MPa with a elongation to failure of 12.9%. Fatigue crack growth resistance and threshold of fine grained samples were lower than that of as-received coarse grained samples. The higher fatigue crack growth rate in the fine grained ECAPed samples may partially arise from small roughness closure effect due to smoother fracture surfaces.

• 한국해양공학회지
• /
• 제22권6호
• /
• pp.52-57
• /
• 2008

The short-term high temperature creep rupture behavior of Ni-based Alloy718 steel was investigated at the elevated temperatures range of 550 to $700^{\circ}C$ under constant stress conditions. The creep rupture characteristics such as creep stress, rupture time, steady state creep rate, and initial strain were evaluated. Creep stress has a quantitative correlation between creep rupture tim and steady state creep rate. The stress exponents (n, m) of the experimental data at 550, 600, 650 and $700^{\circ}C$ were derived as 33.5, -24.9, 26.1, -21.2, 16.8, -12.8 and 10, -8.2, respectively. The stress exponent decreased with increasing creep temperature. The creep lift prediction was derived by the Larson-Miller parameter (LMP) method and the resultant equation was obtained as follows: T($logt_r$+20)=-0.00252 ${\sigma}^2$-1.377${\sigma}$+-22718.

• 대한조선학회지
• /
• 제9권2호
• /
• pp.21-32
• /
• 1972

The problems of thermal stress and residual stress in resistance spot welding are studied from two standpoint namely, effect of temperature distributions and effect of the radius of free boundary. The radius of the region where the temperature distributions are occured is taken as a function of time after welding and as a finite size, 6 times of heated zone. The region of the radial stress distribution is treated as a function of time under Saint-Venant's principle and 6 or 12 times of originally heated zone. Thermal stresses and strains are obtained by analytic solution under constant mechanical properties and by the finite difference method for varing properties under temperature variation. From the computed results following conclusions are derived (1) For the engineering purpose, the region of temperature distribution and stress distribution can be treated as a finite region, $R=r_o=6r_e$ (2) If the maximum temperature of the aluminum alloy plate is less than $500^{\circ}F$, thermal stresses and strains can be obtained with constant mechanical properties. (3) The residual stresses and strains will be remained in welds and its vicinity.

• 한국산학기술학회논문지
• /
• 제9권2호
• /
• pp.281-285
• /
• 2008

냉간단조금형(Cold Forging Die)의 다이블록(Dieblock)을 제작하는 방법 중의 하나로, 다이블록 제작용 재료를 면가공 하여 다이블록 상면(上面)을 마스터펀치(Master Punch)인 호브(Hob)로 압입(Indentation) 시켜 절삭가공((Cutting Work)이 아닌 다이호빙(Die Hobbing) 방법으로 임프레션(Impression)을 성형하여 제작하고 있다. 이 방법에 의하여 다이블록의 재료를 합금공구강(Alloy Tool Steel)인 SKD11을 사용하여 제작하고, 스테인리스판(Stainless Sheet Metal)을 제품 재료로 하여 냉간단조가공(Cold Forging Work)을 수행하였더니 6,000 스트로크(Stroke)에서 금형수명(Die Life)을 다 하고 파손되었다. 본 논문에서는 다이블록 재료를 고속도공구강(High Speed Tool Steel)인 SKH51로 교체 제작하고, 탄소강(Carbon Steel)인 S45C를 제품 재료로 하여 냉간단조가공을 수행하였더니 21,000 스트로크에서 금형수명을 다하고 파손되어 종래의 방법과 비교 검토하였을 때 350%의 금형수명 연장 효과를 얻게 되었다.

• 한국표면공학회지
• /
• 제41권5호
• /
• pp.226-231
• /
• 2008

Titanium and its alloy have been widely used in dental implant and orthopedic prostheses. Electrochemical characteristics of dental implant in the various simulated body fluids have been researched by using electrochemical methods. Ti-6Al-4V alloy implant was used for corrosion test in 0.9% NaCl, artificial saliva and simulated body fluids. The surface morphology was observed using scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDX). The electrochemical stability was investigated using potentiosat (EG&G Co, 263A). The corrosion surface was observed using scanning electron microscopy (SEM). From the results of potentiodynamic test in various solution, the current density of implant tested in SBF and AS solution was lower than that of implant tested in 0.9% NaCl solution. From the results of passive film stability test, the variation of current density at constant 250 mV showed the consistent with time in the case of implant tested in SBF and AS solution, whereas, the current density at constant 250mV in the case of implant tested in 0.9% NaCl solution showed higher compared to SBF and AS solution as time increased. From the results of cyclic potentiodynamic test, the pitting potential and |$E_{pit}\;-\;E_{corr}$| of implant tested in SBF and AS solution were higher than those of implant tested in 0.9% NaCl solution.