• Steel and Composite Structures
• /
• 제6권1호
• /
• pp.15-31
• /
• 2006

Beams with web openings are an attractive system for multi-storey buildings where it is always desirable to have long spans. The openings in the web of steel beams enable building services to be integrated within the constructional depth of a floor, thus reducing the total floor depth. At the same time, the increased beam depth can give high bending moment capacity, thus allowing long spans. However, almost all of the research studies on web openings have been concentrated on beam behaviour at ambient temperature. In this paper, a preliminary numerical analysis using ABAQUS is conducted to develop a general understanding of the effect of the presence of web opening on the behaviour of steel beams at elevated temperatures. It is concluded that the presence of web openings will have substantial influence on the failure temperatures of axially unrestrained beams and the opening size at the critical position in the beam is the most important factor. For axially restrained beams, the effect of web openings on the beam's large deflection behaviour and catenary force is smaller and it is the maximum opening size that will affect the beam's response at very high temperatures. However, it is possible that catenary action develops in beams with web openings at temperatures much lower than the failure temperatures of the same beam without axial restraint that are often used as the basis of current design.

• 접착 및 계면
• /
• 제13권3호
• /
• pp.137-144
• /
• 2012

탄소나노소재의 화학적 기능화는 대부분 복합체 제조 시 고분자 모재(matrix)와의 계면 특성 향상을 위한 방법으로 적용되어 왔다. 계면결합력의 증가에 따른 효과는 기계적 물성의 증가를 통해 간접적으로 확인할 수 있으며, 이는 계면에서 효과적인 응력전달을 통해 설명된다. 보다 직접적으로 기능화를 통한 계면결합력 증가의 효과를 설명하기 위하여 피에조 저항효과를 관찰할 수 있으며, 이를 통하여 변형에 대한 복합체 내부의 전도성 충진재의 거동을 짐작해 볼 수 있다. 이를 위해 다중벽 탄소나노튜브(MWCNT)와 환원 그래핀(rGO)을 황산/질산 용액을 이용하여 산화반응을 통해 기능기를 도입하였으며, 기능화 전 후의 복합체의 전기적 저항 및 피에조 저항효과를 측정하였다. 결과로부터 기능기 도입으로 인해 증가한 탄소나노소재의 구조적 결함이 전기적 저항의 증가를 야기하지만 동일한 변형에 대하여 저항 변화가 더 크게 나타나 변형에 따른 복합체 내부 전도성 입자의 유동성이 증가함을 확인하였고, 이를 통해 계면결합력이 증가함을 피에조 저항효과 관찰을 통해 확인할 수 있었다.

• Journal of Dental Anesthesia and Pain Medicine
• /
• 제21권2호
• /
• pp.139-153
• /
• 2021

Background: In anesthetic techniques, touching bones can cause needle bending. Theoretically, a needle should support such deflection without fracturing. However, it is possible that a needle may fracture depending on the quality and type of needle used. This study evaluated the physical, chemical, and micromorphological characteristics of long and short dental anesthetic needles, as well as the mechanical properties of flexural load and bending resistance when needles are subjected to different bending angles. Methods: Long and short needles (30G, Jets, Misawa, Selekto, Terumo, Unoject and 27G, Dencojet, Injex, Jets, Misawa, Procare, Setoject XL, Terumo) were evaluated. Scanning electron microscopy was used to evaluate the needle bevels and energy-dispersive X-ray spectroscopy was used for the chemical analysis of needle compositions. Flexural loading and bending strength assessments were performed using a universal testing machine by bending the needles (n = 5) to angles of 30°, 60°, or 90°, or until fracture occurred. Results: The Injex 27G, Jets 27G, and Septoject XL 27G needles were all less than 30 mm in length. There were small percentage variations in the chemical compositions of the needles. Superior smoothness was observed for the Unoject 30G needle, which exhibited the highest fracture resistance at 60°. The Jets 30G needle exhibited greater resistance to fractures at 90°. The Procare 27G needle exhibited the highest load resistance to bending, followed by the Septoject XL 27G needle, and both needles were tied for the lowest fracture resistance. No needle fractured when bent to 30° or at less than three bends to 60° or 90°. Conclusions: Greater needle resistance to bending increases the probability of early fracturing. Thinner and shorter needles are more resistant than longer and thicker needles. Performing a single bend does not result in any significant risk of fracture or obliterate the lumen, allowing for the continued passage of anesthetic liquid.

• 국제학술발표논문집
• /
• The 9th International Conference on Construction Engineering and Project Management
• /
• pp.563-570
• /
• 2022

Industrialized and modular construction is a growing construction technique that can transfer a large portion of the construction process to off-site fabrication yards. This method of construction often involves the fabrication, pre-assembly, and transportation of massive and long volumetric modules. The module weight keeps increasing as the modules become more complete (with infill) to minimize the work at the site and, as higher productivity can be achieved at the fabrication shop. Thus, a volumetric module delivery gets more challenging and risky. Despite its importance, past research paid relatively insufficient attention to the problem related to the lifting of heavy modules. This can be a complex and time-consuming problem with multiple lifting for transportation-and-installation operations both in fabrication yard and jobsite, and require complex crane operations (sometimes, more than one crane) due to crane load capacity and load balance/stability. This study investigates this problem by focusing on the structural perspective of lifting such long volumetric modules through simulation studies. Various scenarios of lifting a weighty module from the top using four lifting cables attached to crane hooks (either a single crane or double crane) are simulated in SAP software. The simulations account for various factors pertaining to structural indices, e.g., bending stress and deflection, to identify a proper method of module lifting from a structural point of view. The method can identify differences in structural indices allowing identification of structural efficiency and safety levels during lifting, which further allows the selection of the number of cranes and location of lifting points.