• Journal of Welding and Joining
• /
• v.34 no.6
• /
• pp.16-19
• /
• 2016

Needs for structural integrity procedure such as BS 7910, the nuclear industry document R6 Rev.4 and the European FITNET procedure are being increased in industry. Especially, BS 7910 allows metallic structures to be assessed on the basis of fracture mechanics analysis rather than strict adherence to design and fabricated codes. This study is to propose the flaw assessment to judge the toughness level of welding consumables at the development stage. The FCA welding consumables with YP 690MPa and CTOD over 0.25 mm have been developed and its allowable weld flaw size considering actually applied environment has been evaluated. Since the estimated allowable defect size is sufficiently detectable in nondestructive testing, the toughness of the developed material is judged to be appropriate and no problem in securing the structural integrity.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.2
• /
• pp.278-285
• /
• 1988

The Critical size of artificially induced micro-holes in 0.17%, 0.36% Carbon steel Specimens with Spheroidized Cementite and in 0.17% carbon steel specimens with martensite structure is compared with annealed pre-crack in order to discuss the physical meaning of the fatigue limit and evaluation of the tolerant micro flaw size at the stress level of the fatigue limit. Results obtained were summarized as follows; (1) In this study, non-propagating crack length of Smooth specimen and critical pre-crack length (lc) is coincide. (2) In the carbon steels with spheroidized cementite structure, critical pre-crack length (lc) and allowable micro-hole size (dc) is coincide each other at the fatigue limit level. (3) It has been published that there exists a particular size of micro-hole which has no effect on the fatigue limit. In this study, the micro-hole of critical size can be regarded as equivalent to a tolerant micro flaw which would not reduce the fatigue limit.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05c
• /
• pp.193-198
• /
• 1996

The effect of dynamic strain aging (DSA) on the leak-before-break (LBB) analysis was estimated through the evaluation of leakage-size-crack and flaw stability in SA106 Gr.C piping steel. Also. the results were represented as a form of "LBB allowable load window". In the DSA temperature region. the leakage-size-crack length was smaller than that at other temperatures and it increased with increasing tensile strain rate. In the results of flaw stability analysis. the lowest instability load appeared at the temperature corresponding to minimum J- R curve which was caused by DSA. The instability load near the plant operating temperature depended on the loading rate of J-R data. and decreased with increasing tensile strain rate. These are due to the strain hardening characteristic and strain rate sensitivity of DSA. In the "LBB allowable load window". LBB allowable region was the narrowest at the temperature and loading conditions where DSA occurs.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.8 no.1
• /
• pp.6-11
• /
• 1988

The comparison and analysis of flaw detectability, flaw sizing methods and allowable criteria in accordance with the applicable codes, ASME and RCC-M Code, in ultrasonic examination of pressure vessel in nuclear power plants were studied. Accordding to the codes, calibration blocks were made. The artificial flaws such as disc and band types in test specimens were machined. They were detected and evaluated with etch code requirements and measured values were compared with the actual flaws.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.6
• /
• pp.1013-1017
• /
• 2012

Advanced composite-sintered bushings are widely utilized in the areas of excavators and injection molding machines as a journal bearing. Since the bearings are mainly used under high loads, service life should be long and the stored oil of inner bushings has to be continually fed into the bearing. The composite-sintered bushings are consisted of the two different materials; outer steel materials and inner porous sintered materials respectively. High temperature diffusion bonding has been applied for holding the both materials of the bushing together. Therefore, it is very important that the bonding reliability has to be assured and evaluated in manufacturing process. Finite element method (FEM) is performed in order to evaluate the minimum allowable flaw sizes that are possibly generated in the composite-sintered bushings. Additionally, the composite-sintered bushings were undergone ultrasonic C-scan tests to find out the size of inherent flaws through artificially simulated UT signal analysis.