• 한국산업융합학회 논문집
• /
• 제9권1호
• /
• pp.67-72
• /
• 2006

This study is on the development of algorithm of surge test for quality control on electrical parts of throttle body in automobiles with internal combustion engine, not only to know its condition to be good or not, but also jugding its condition to be classified into six types. To know whether its condition to be good or not, comparing and analyzing between two waveforms generated from master and test coil of throttle body. If test net area is below 20% of master area, the condition of test coil is good. By analyzing test coil waveform to master coil waveform, the condition of test coil into winding badness, insulation badness, layer and corona discharge, short badness should known. Therefore quality control system on electrical parts of throttle body should be developed.

• Transactions on Electrical and Electronic Materials
• /
• 제16권6호
• /
• pp.317-322
• /
• 2015

The metal oxide varistor (MOV) is a major component of the surge protection devices (SPDs) currently in use. The device is judged to be faulty when fatigue caused by the continuous inflow of lightning accumulates and reaches the damage limit. In many cases, induced lightning resulting from lightning strikes flows in to the device several times per second in succession. Therefore, the frequency or the rate at which the SPD is actually exposed to stress, called a surge, is outside the range of human perception. For this reason, the protective device should be replaced if it actually approaches the end of its life even though it is not faulty at present, currently no basis exists for making the judgment of remaining lifetime. Up to now, the life of an MOV has been predicted solely based on the number of inflow surges, irrespective of the magnitude of the surge current or the amount of energy that has flowed through the device. In this study, nonlinear data that shows the damage to an MOV depending on the count of surge and the amount of input current were collected through a high-voltage test. Then, a failure prediction algorithm was proposed by preparing a look-up table using the results of the test. The proposed method was experimentally verified using an impulse surge generator

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.558-560
• /
• 2004

Studies on the controlled switching method have been done to prevent the power system surges which cause the insulation deterioration and electro magnetic compatibility (EMC) problems during closing and opening of a circuit breaker. The controlled switching method controls the closing and tripping time in coincidence with the voltage or current to suppress switching surge. It is used to switch condenser bank, no load transformer, and shunt reactor. In this study, basic concept of the controlled switching is introduced, and also the test is performed to find parameters of the controlled switching in a 24kV vacuum circuit. And then, the control device hardware using TMS320C31 DSP has been designed and manufactured. It has been found that the application of IT technology to a circuit breaker is very effective to depress the switching surge.

• 한국안전학회지
• /
• 제29권5호
• /
• pp.47-53
• /
• 2014

Despite the automatic fire alarm system, according to the national fire data system of national emergency management agency, the fires account for 40,932 incidents, 2,184 injuries and about 430 billion won in property losses in 2013. Since the conventional automatic fire alarm system has several weaknesses related to electrical signal such as noise, surge, lighting, etc. Most fires are mainly caused by electrical faults, mechanical problem, chemical, carelessness and natural. The electrical faults such as line to ground fault, line to line fault, electrical leakage and arc are one of the major problems in fire. This paper describes the development of a novel real-time fire monitoring system algorithm including fault detection function which puts the existing optic smoke and heat detectors for fire detection with current and voltage sensors in order to utility fault monitoring using high accuracy DAQ measurement system with LabVIEW program. The fire detection and electrical fault monitoring with a proposed a new detection algorithm are implemented under several test. The fire detection and monitoring system operates according to the proposed algorithm well.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2000년도 추계학술대회논문집
• /
• pp.63-71
• /
• 2000

In this study a drift prediction model based on fluid dynamics theory is introduced. The essential effects of environmental loads and target characteristics are taken into account from a fluid dynamics point of view. The governing equations of motion are derived from Newton's law of dynamics. In the mathematical formulation only three degrees of freedom(surge, sway, yaw) of the drifting object are assumed and the environmental loads considered are the forces and moments by wind and current. A computer algorithm for this model is implemented to obtain the numerical result in the time domain. The preliminary tests for model verification are conducted and the results are compared with the field experiment data as well as leeway formula suggested from the field test data.

• 한국항만학회지
• /
• 제14권3호
• /
• pp.353-360
• /
• 2000

In this study a drift prediction model based on fluid dynamics theory is introduced. The essential effects of environmental loads and target characteristics are taken into account from a fluid dynamics point of view. The governing equations of motion are derived from Netwon's law of dynamics. In the mathematical formulation only three degrees of freedom(surge, sway, yaw) of the drifting object are assumed and the environmental loads considered are the forces and moments by wind and current. A computer algorithm for this model is implemented to obtain the numerical result in the time domain. The preliminary tests for model verification are conducted and the results are compared with the field experiment data as well as leeway formula suggested from the field test data.

• Nuclear Engineering and Technology
• /
• 제28권4호
• /
• pp.405-414
• /
• 1996

In this paper, the unsteady 2-dimensional turbulent flow model for thermal stratification in a pressurizer surge line of PWR plant is proposed to numerically investigate the heat transfer and flow characteristics. The turbulence model is adapted to the low Reynolds number K-$\varepsilon$ model (Davidson model). The dimensionless governing equations are solved by using the SIMPLE (Semi-Implicit Method for Pressure Linked Equations) algorithm. The results are compared with simulated experimental results of TEMR Test. The time-dependent temperature profiles in the fluid and pipe nil are shown with the thermal stratification occurring in the horizontal section of the pipe. The corresponding thermal stresses are also presented. The numerical result for thermal stratification by the outsurge during heatup operation of PWR shows that the maximum dimensionless temperature difference is about 0.83 between hot and cold sections of pipe well and the maximum thermal stress is calculated about 322MPa at the dimensionless time 28.5 under given conditions.

• 한국해안·해양공학회논문집
• /
• 제26권5호
• /
• pp.292-299
• /
• 2014

기존의 태풍에 의한 해안 범람 수치모의 연구의 대부분은 폭풍해일만을 고려하였으므로 강우에 의한 추가적인 침수는 배제되어 왔다. 일반적으로 태풍은 강우를 동반한 자연재해이므로 폭풍해일에 의한 해안 도시범람을 수치모의 하는 데 있어 반드시 강우의 영향이 고려되어야 한다. 또한 강우는 도시 우수 관망을 통해 바다로 배출되므로 강우를 동반하는 폭풍해일 수치모의 시 우수관망 시스템이 고려되어야 타당한 결과를 얻을 수 있다. 본 연구에서는 기존의 폭풍해일 수치모형에 강우와 우수관망을 해석할 수 있는 알고리즘을 추가하여 수치모형을 개발하였다. 개발된 수치모형을 단순화된 지형에 적용하여 강우에 의한 범람과 우수의 배수, 해수의 역류현상, 우수의 배수에 따른 해수면 상승 등 기본적인 수치모형의 기능을 검사하였다. 그 결과 다양한 조건에서 수치모형이 정상적으로 작동되는 것을 확인하였다.

• 대한원격탐사학회지
• /
• 제32권5호
• /
• pp.539-550
• /
• 2016

육상의 수체를 탐지하는 것은 홍수, 태풍, 지진해일과 같은 재해 모니터링에 있어 핵심적인 사항이며, 습지, 빙하 등 지표 수자원의 시 공간적 변화를 파악하는데 중요한 역할을 한다. 본 연구에서는 Kompsat-5 SAR 영상으로부터 육상의 수체를 탐지하기 위하여 임계값에 기반한 접근방법의 적용성을 분석하고, 다양한 임계값 설정 기법의 탐지 성능을 평가하였다. 또한 SAR 영상의 스펙클 필터링이 임계값 설정에 미치는 영향을 분석하였으며, 영상에서 수체가 차지하는 비율에 따른 탐지 성능의 변화에 대한 정량적인 평가를 수행하였다. 추가적으로 탐지 성능을 향상시키기 위해 히스토그램의 bimodality 검정과 majority filtering 처리를 활용하는 새로운 알고리즘을 제안하였다. 세종시 지역의 사례의 경우 제안된 알고리즘을 통해 최종적으로 약 96%의 탐지율과 0.3%의 오탐지율로 수체를 탐지할 수 있음을 보였다.

• 한국재난정보학회 논문집
• /
• 제17권4호
• /
• pp.684-693
• /
• 2021

연구목적: 아두이노를 이용하여 실시간 대지저항 데이터를 취득할 수 있는 스마트 대지저항 측정장치를 개발하여 낙뢰 등 이상전압으로부터 안전한 설비환경을 구축하는것에 목적이 있다. 연구방법: 본 논문은 아두이노와 전력선 통신(PLC) 체계를 갖춘 대지저항 취득 및 분석 시스템을 개발하여 설계모델과 적용사례를 연구하였다. 경남지역의 풍력발전 단지 내 일부 부지를 테스트 베드로 선정하여 신기술을 적용한 실시간 대지저항 데이터를 취득하였다. 전극배열은 웨너(Wenner) 4전극배열과 슐렘버거(Schlumberger) 전극배열을 혼용한 스마트 전극배열을 채택하였다. 연구결과: 본 기술의 특징은 첫 번째로 스마트 다 전극의 깊이를 각기 다르게 편성해 층간에 특이성을 가지는 지층 구조에도 취득 데이터의 오차범위를 축소하였다. 두 번째로 스마트 접지전극에서 취득한 대지저항 데이터의 정보를 사물인터넷으로 실시간 송·수신이 가능하도록 IT융합 기술을 적용하였다. 마지막으로 규칙적인 관리 체계를 구축하고 Server에 축적된 빅 데이터를 분석하여 다양한 요소들의 변화추이를 확인할 수 있으며, IT융합 환경에 최적의 접지 알고리즘과 접지시스템 설계 모델링이 가능하다. 결론: 본 기술은 4차 산업 시대에 근간이 되는 도시 기반시설에 낙뢰로 인한 서지(Surge)의 피해를 줄이고 최적화된 접지시스템 모델을 설계하여 사용자의 안전과 생명을 보호 할 것이다. 또한 순수 국산 기술력의 지적재산권을 확보하여 포스트 코로나 시대에 팬데믹으로 정체되어있는 우리산업의 일자리 창출과 활기를 불어넣는 효과도 기대된다.