• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.331-332
• /
• 2007

Surface micromachined SiC devices have readily been fabricated from the polycrystalline (poly) 3C-SiC thin film which has an advantage of being deposited onto $SiO_2$ or $Si_3N_4$ as a sacrificial layer. Therefore, in this work, magnetron reactive ion etching process which can stably etch poly 3C-SiC thin films grown on $SiO_2$/Si substrate at a lower energy (70 W) with $CHF_3$ based gas mixtures has been studied. We have investigated the etching properties of the poly 3C-SiC thin film using PR/Al mask, according to $O_2$ flow rate, pressure, RF power, and electrode gap. The etched RMS (root mean square), etch rate, and etch profile of the poly 3C-SiC thin films were analyzed by SEM, AFM, and $\alpha$-step.

• Elastomers and Composites
• /
• v.54 no.1
• /
• pp.1-6
• /
• 2019

In this study, we measured the leakage current at $30{\sim}80^{\circ}C$ and $90{\sim}170^{\circ}C$ under a voltage of 200~980 V applied to samples (ordinary temperature) and polyamide film specimens degraded at $170^{\circ}C$ for 20 minute respectively. After the specimen was degraded at $130^{\circ}C$ and $50^{\circ}C$, a voltage of 200 to 800 V was applied for 10 to 60 minutes. The measurement of the leakage current resulted in the following conclusions. In the case of using Al and Cu as the main electrode, it was confirmed that the leakage current also increased in high temperatures as the voltage increased. Regardless of the type of main electrode, when the temperature was constant at $130^{\circ}C$ and $50^{\circ}C$, the leakage current increased as the voltage increased, and gradually decreased with time. As a result of the FTIR measurement, the main absorption of the infrared absorption spectrum was C=O at about $1650cm^{-1}$ and N-H diagonal vibration occurred at around $1550cm^{-1}$. There was no change in the material, so no effect of temperature was observed. By the results of SEM measurements, as the temperature of degradation increases, cracks in the specimen disappear. This may be because the amide bond (-CO-NH-) is absorbed by the material.

• The korean journal of orthodontics
• /
• v.44 no.5
• /
• pp.246-253
• /
• 2014

Objective: To evaluate the bioactivity, and the biomechanical and bone-regenerative properties of Ti6Al4V miniscrews subjected to anodization, cyclic precalcification, and heat treatment (APH treatment) and their potential clinical use. Methods: The surfaces of Ti6Al4V alloys were modified by APH treatment. Bioactivity was assessed after immersion in simulated body fluid for 3 days. The hydrophilicity and the roughness of APH-treated surfaces were compared with those of untreated (UT) and anodized and heat-treated (AH) samples. For in vivo tests, 32 miniscrews (16 UT and 16 APH) were inserted into 16 Wistar rats, one UT and one APH-treated miniscrew in either tibia. The miniscrews were extracted after 3 and 6 weeks and their osseointegration (n = 8 for each time point and group) was investigated by surface and histological analyses and removal torque measurements. Results: APH treatment formed a dense surface array of nanotubular TiO2 layer covered with a compact apatite-like film. APH-treated samples showed better bioactivity and biocompatibility compared with UT and AH samples. In vivo, APH-treated miniscrews showed higher removal torque and bone-to-implant contact than did UT miniscrews, after both 3 and 6 weeks (p < 0.05). Also, early deposition of densely mineralized bone around APH-treated miniscrews was observed, implying good bonding to the treated surface. Conclusions: APH treatment enhanced the bioactivity, and the biomechanical and bone regenerative properties of the Ti6Al4V alloy miniscrews. The enhanced initial stability afforded should be valuable in orthodontic applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.163-163
• /
• 1999

MOSFET, MESFET 그리고 MODFET는 Logic ULSIs, high speed ICs, RF MMICs 등에서 중요한 역할을 하고 있으며, 그것의 gate electrode, contact, interconnect 등의 물질로는 refractory metal을 이용한 CoSi2, MoSi2, TaSi2, PtSi2, TiSi2 등의 효과를 얻어내고 있다. 그중 TiSi2는 비저항이 가장 낮고, 열적 안정도가 좋으며 SAG process가 가능하므로 simpler alignment process, higher transconductance, lower source resistance 등의 장점을 동시에 만족시키고 있다. 최근 소자차원이 scale down 됨에 따라 TiSi2의 silicidation 과정에서 C49 TiSi2 phase(high resistivity, thermally unstable phase, larger grain size, base centered orthorhombic structure)의 출현과 그것을 제거하기 위한 노력이 큰 issue로 떠오르고 있다. 여러 연구 결과에 따르면 PAI(Pre-amorphization zimplantation), HTS(High Temperature Sputtering) process, Mo(Molybedenum) implasntation 등이 C49를 bypass시키고 C54 TiSi2 phase(lowest resistivity, thermally stable phase, smaller grain size, face centered orthorhombic structure)로의 transformation temperature를 줄일 수 있는 가장 효과적인 방법으로 제안되고 있지만, 아직 그 문제가 완전히 해결되지 않은 상태이며 C54 nucleation에 대한 physical mechanism을 밝히진 못하고 있다. 본 연구에서는 증착 시 기판온도의 변화(400~75$0^{\circ}C$)에 따라 silicon 위에 DC/RF magnetron sputtering 방식으로 Ti/Si film을 각각 제작하였다. 제작된 시료는 N2 분위기에서 30~120초 동안 500~85$0^{\circ}C$의 온도변화에 따라 RTA법으로 각각 one step annealing 하였다. 또한 Al을 cosputtering함으로써 Al impurity의 존재에 따른 영향을 동시에 고려해 보았다. 제작된 시료의 분석을 위해 phase transformation을 XRD로, microstructure를 TEM으로, surface topography는 SEM으로, surface microroughness는 AFM으로 측정하였으며 sheet resistance는 4-point probe로 측정하였다. 분석된 결과를 보면, 고온에서 제작된 박막에서의 C54 phase transformation temperature가 감소하는 것이 관측되었으며, Al impuritydmlwhswork 낮은온도에서의 C54 TiSi2 형성을 돕는다는 것을 알 수 있었다. 본 연구에서는 결론적으로, 고온에서 증착된 박막으로부터 열적으로 안정된 phase의 낮은 resistivity를 갖는 C54 TiSi2 형성을 보다 낮은 온도에서 one-step RTA를 통해 얻을 수 있다는 결과와 Al impurity가 존재함으로써 얻어지는 thermal budget의 효과, 그리고 그로부터 기대할 수 있는 여러 장점들을 보고하고자 한다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.70-73
• /
• 2001

MFIS(Metal-ferroelectric-insulator- semiconductor) structures using silicon oxynitride(SiON) buffer layers were fabricatied and demonstrated nonvolatile memory operations. Oxynitride(SiON) films have been formed on p-Si(100) by RTP(rapid thermal process) in O$_2$+N$_2$ ambient at 1100$^{\circ}C$. The gate leakage current density of Al/SiON/Si(100) capacitor was about the order of 10$\^$-8/ A/cm$^2$ at the range of ${\pm}$ 2.5 MV/cm. The C-V characteristics of Al/LiNbO$_3$/SiON/Si(100) capacitor showed a hysteresis loop due to the ferroelectric nature of the LiNbO$_3$ thin films. Typical dielectric constant value of LiNbO$_3$ film of MFIS device was about 24. The memory window width was about 1.2V at the electric field of ${\pm}$300 kV/cm ranges.

• Journal of the Microelectronics and Packaging Society
• /
• v.1 no.2
• /
• pp.125-134
• /
• 1994

저항범위가 다른 두종류의 Ru계 후막저항계(1Kohm/sq. 100kohm/sq.)를 선택하여 도전상의 상전이 기구를 반응조건을 변화시켜 연구하였다. 저저항체의 경우 도전상으로는 RuO2였으며 700-100$0^{\circ}C$에서 1시간 반응한 경우 반응온도에 따른 구성상의 변화는 없었다 반응온도 90$0^{\circ}C$에서 반응시간이 경과함에 따라 도전상은 RuO2가 Glass의 구성성분인 Pb와 반응하여 Rb2(Ru1.69 Pb0.31)O6.5로 변하고 시간이 36시간 경과한 후에는 도전상이 Pb4Al2Si2O10인 결정으로 둘러 쌓이는 반응인 peritectic reaction이 일어났다. 고전항체의 경 우 도전상으로는 Pb2(Ru1.69 Pb0.31)O6.5로 변하고 시간이 36시간 경과한 후에는 더전상이 Pb4Al2Si2O10인 결정으로 둘러쌓이는 반응인 peritectic reaction 이 일어났다. 고저항체의 경 우 도전상으로는 Pb2(Ru1.69 Pb0.31)O6.5인 pyrochrole 상이였다. 100$0^{\circ}C$에서 1시간 반응시킬 경 우 도전상이 RuO2로 변하였다. 반응온도를 90$0^{\circ}C$로 하고 반응시간을 변화시키면 도전상인 Pb2(Ru1.69 Pb0.31)O6.5가 (Ru1.69Pb0.31)O4x로 변하면서 공존하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.84-84
• /
• 2010

In this study, we report on the novel lithographic patterning method to fabricate organic-semiconductor devices based on photo and e-beam lithography with well-known silicon technology. The method is applied to fabricate pentacene-based organic field effect transistors. Owing to their solubility, sub-micron sized patterning of P3HT and PEDOT has been well established via micromolding in capillaries (MIMIC) and inkjet printing techniques. Since the thermally deposited pentacene cannot be dissolved in solvents, other approach was done to fabricate pentacene FETs with a very short channel length (~30nm), or in-plane orientation of pentacene molecules by using nanometer-scale periodic groove patterns as an alignment layer for high-performance pentacene devices. Here, we introduce the atomic layer deposition of $Al_2O_3$ film on pentacene as a passivation layer. $Al_2O_3$ passivation layer on OTFTs has some advantages in preventing the penetration of water and oxygen and obtaining the long-term stability of electrical properties. AZ5214 and ma N-2402 were used as a photo and e-beam resist, respectively. A few micrometer sized lithography patterns were transferred by wet and dry etching processes. Finally, we fabricated sub-micron sized pentacene FETs and measured their electrical characteristics.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.1
• /
• pp.16-22
• /
• 2023

In a solar cell, degradation refers to the decrease in performance parameters caused by defects originated due to various causes. During the fabrication process of solar cells, degradation is generally related to the processes such as passivation or firing. There exist sources of many types of degradation; however, the exact cause of Light and elevated Temperature Induced Degradation (LeTID) is yet to be determined. It is reported that the degradation and the regeneration occur due to the recombination of hydrogen and an arbitrary substance. In this paper, we report the deposition of Al₂O₃ and SiN_X on silicon wafers used in the Passivated Emitter and Rear Contact (PERC) solar structure and its degradation pattern. A higher degradation rate was observed in the sample with single layer of Al₂O₃ only, which indicates that the degradation is affected by the presence or the absence of a passivation thin film. In order to alleviate the degradation, optimization of different steps should be carried out in consideration of degradation in the solar cell fabrication process.

• Korean Journal of Materials Research
• /
• v.13 no.6
• /
• pp.347-351
• /
• 2003

II-Ⅵ ZnO compound semiconductor thin films were grown on $\alpha$-Al$_2$O$_3$(0001) single crystal substrate by radical beam assisted molecular beam epitaxy and the optical properties were investigated. Zn(6N) was evaporated using Knudsen cell and O radical was assisted at the partial pressure of 1$\times$10$^{4}$ Torr and radical beam source of 250-450 W RF power. In $\theta$-2$\theta$ x-ray diffraction analysis, ZnO thin film with 500 nm thickness showed only ZnO(0002)and ZnO(0004) peaks is believed to be well grown along c-axis orientation. Photoluminescence (PL) measurement using He-Cd ($\lambda$=325 nm) laser is obtained in the temperature range of 9 K-300 K. At 9 K and 300 K, only near band edge (NBE) is observed and the FWHM's of PL peak of the ZnO deposited at 450 RF power are 45 meV and 145 meV respectively. From no observation of any weak deep level peak even at room temperature PL, the ZnO grains are regarded to contain very low defect density and impurity to cause the deep-level defects. The peak position of free exciton showed slightly red-shift as temperature was increased, and from this result the binding energy of free exciton can be experimentally determined as much as $58\pm$0.5 meV, which is very closed to that of ZnO bulk. By van der Pauw 4-point probe measurement, the grown ZnO is proved to be n-type with the electron concentration($n_{e}$ ) $1.69$\times$10^{18}$$cm^3$, mobility($\mu$) $-12.3\textrm{cm}^2$/Vㆍs, and resistivity($\rho$) 0.30 $\Omega$$\cdot$cm.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.97.1-97.1
• /
• 2010

유연금속기판위에 DC 마그네트론 스퍼터링을 이용하여 Ag/ZnO 이중구조의 후면반사막을 증착하고 Ag 표면조도 변화에 따른 후면반사막의 반사특성 변화와 플렉서블 비정질 실리콘 박막 태양전지의 셀 특성에 미치는 영향을 조사하였다. Substrate구조를 갖는 플렉서블 실리콘 박막 태양전지에서는 실리콘 박막 광흡수층의 상대적으로 낮은 광 흡수율로 인하여 입사광에 대한 태양전지 내에서의 광 산란 및 포획이 태양전지 효율을 증대시키는데 매우 중요한 역할을 하는 것으로 알려져 있다. 플렉서블 실리콘 박막 태양전지에서의 후면반사막은 광 흡수층에서 흡수되지 않는 입사광을 다시 반사시켜 광 흡수를 증대시키며 이때 후면반사막 표면에서 반사 빛을 효율적으로 산란시켜 이동경로를 증대시킴으로써 광 흡수율을 더욱 향상시킬 수 있다. 본 연구에서는 유연금속 기판위에 Ag와 ZnO:Al($Al_2O_3$ 2.5wt%) 타겟을 사용한 DC 마그네트론 스퍼터링법으로 Ag/AZO 이중구조의 후면반사막을 제조하고, Ag 박막의 표면형상 변화와 이에 따른 후면반사막의 반사도 변화를 비교, 분석하였다. 증착 조건 변화에 따른 표면 형상 및 반사 특성은 Atomic Force Mircroscope(AFM), Scanning electron miroscopy(SEM), UV-visible-nIR spectrometry를 통하여 분석하였다. 서로 다른 표면 거칠기를 갖는 후면반사막 위에 n-i-p구조의 a-Si:H 실리콘 박막 태양전지를 제조한 후 태양전지 동작 특성에 미치는 영향을 조사하였다. n,p층은 13.56MHz PECVD, i층은 60MHz VHF CVD를 사용하여 각각 제조 하였으며, Photo I-V, External Quantum Efficiency(EQE) 분석을 통하여 태양전지 특성을 조사 하였다. SEM 분석결과 공정 온도가 증가 할수록 Ag 박막의 표면 결정립 크기도 증가하였으며, AFM분석을 통한 Root-mean-square(Rms)값은 상온에서 $500^{\circ}C$로 증착온도가 증가함에 따라 6.62nm에서 46.64nm까지 증가하였다. Ag 박막의 표면 거칠기 증가에 따라 후면반 사막의 확산 반사도도 함께 증가하였다. 공정온도 $500^{\circ}C$에서 증착된 후면반사막을 사용하여 a-Si:H 태양전지를 제조하였을 때 상온에서 제조한 후면반사막에 비하여 단락전류밀도 (Jsc)값은 9.94mA/$cm^2$에서 13.36mA/$cm^2$로 증가하였으며, 7.6%의 가장 높은 태양전지 효율을 나타내었다.