• 한국세라믹학회지
• /
• 제26권5호
• /
• pp.593-600
• /
• 1989

Fine spinel powder was prepared from the Mg-Al double alkoxide synthesized using magnesium powder, aluminum foil and sec-butyl alcohol. This powder was compared with powder prepared by mixing two commercial alkoxides. The spinelization was started at 50$0^{\circ}C$ and was almost completed at 100$0^{\circ}C$ with a good crystallinity in the double alkoxide system. In mixed alkoxide system, homogeneous spinel powder was not obtained and MgO existed as a second phase because of solubility and hydrolysis rate differences of two alkoxides. The relative density of specimen prepared by double alkoxide was 99% and specimen prepared by mixed alkoxide was 95%. The modulus of rupture of specimens prepared by double alkoxide and mixed alkoxide was 49.9kg/$\textrm{mm}^2$ and 41.6kg/$\textrm{mm}^2$, respectively.

• 동력기계공학회지
• /
• 제5권4호
• /
• pp.74-81
• /
• 2001

The infiltration behavior of molten Al-alloy, microstructures, hardness, and the interfacial reactions of $SiC_p/Al$ composites fabricated by the pressureless infiltration technique were investigated. It was made clear that both the weight fraction of SiC reinforcement and additive Mg content considerably influenced on the infiltration behavior of the molten Al-alloy matrix. Complete infiltration of molten Al-alloy achieved under the conditions that weight fraction of SiC content is more than 30wt%, and additive Mg content is more than 9wt%. Interfacial region of Al-alloy matrix and SiC reinforcement phase, $Mg_2Si$ was formed by the reaction between Mg and SiC. Another reaction product AlN was also formed by the reaction between Al-alloy matrix and gas atmosphere nitrogen.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2016년도 추계학술대회 논문집
• /
• pp.109-109
• /
• 2016

철을 보호하는 코팅막에 있어서 현재는 우수한 희생방식성을 가지는 아연(Zn)이 많은 분야에서 활용되고 있지만 성능 향상을 위해서는 코팅막의 두께 증가가 필연적이다. 동일한 두께 혹은 그 이하에서 더 나은 내식성을 가지는 코팅막을 개발하는 목적으로 알루미늄(Al)과 마그네슘(Mg)을 이용한 코팅막의 개발을 진행하고 있으며 이 발표에서는 Al과 Mg의 코팅막을 다층으로 제작하여 이전 실험의 Al-Mg 코팅 강판과 비교 하였을 때 어떠한 특성이 나타나는지를 확인하였다. Al-Mg 코팅층은 99.999%의 Al, 99.99%의 Mg target을 사용하여 스퍼터링을 이용하여 냉연강판 위에 코팅하였다. 증발물질과 기판과의 거리는 7cm 이며, 기판은 세척을 실시한 후 클리닝 챔버에 장착하고 ${\sim}10^{-5}Torr$ 까지 진공배기를 실시하였다. 클리닝 챔버가 기본 압력까지 배기되면 아르곤 가스를 주입하고 기판홀더에 -800 V의 직류 전압을 인가하여 약 30분간 글로우 방전 청정을 실시하였다. 기판의 청정이 끝나면 아르곤 가스를 차단하고 코팅 챔버로 시편을 이송 후 코팅층 성분의 구성형태에 따라 Al과 Mg을 코팅하였다. Al-Mg 코팅층은 $5{\mu}m$의 두께를 기준으로 계면의 코팅층이 각각 Al과 Mg이며 다층으로 구성된 코팅층을 제작하였다. 그리고 후속 공정으로 질소 분위기 $400^{\circ}C$에서 10분간 열처리를 하였다. Al-Mg 코팅층을 주사전자현미경(SEM)으로 관찰한 결과, 표면에서는 Al 또는 Mg의 결정성 구조를 보였으며 단면에서는 다층의 경계를 조금이지만 확인할 수 있었으며 글로우방전분광기(GDLS)를 통해 열처리 후에는 층의 구분이 모호해 지는 것을 확인 할 수 있었다. 그리고 XRD를 통하여 열처리 후 Al-Mg 합금상의 생성도 확인하였다. 또한 Al-Mg가 다층으로 코팅된 강판을 염수분무시험을 통해서 내부식 특성을 확인하였다. Al-Mg 코팅 강판의 염수분무시험 결과, 모든 제작된 코팅층에서 열처리 전 보다 열처리 후 3배 이상의 내식성의 향상효과를 확인할 수 있었다. 이러한 결과로부터 열처리에 의한 합금상 생성 그리고 Al-Mg 박막의 미세구조 변화가 강판의 내식성에 영향을 미치고 있다는 것을 확인할 수 있었지만 다층 제작이 미치는 영향에 대해서는 좀 더 연구가 필요한 것으로 판단된다.

• International Journal of Precision Engineering and Manufacturing
• /
• 제6권3호
• /
• pp.56-59
• /
• 2005

Aluminum alloy casting is gaining increased acceptance in automotive and electronic industries and especially, squeeze casting is the most efficient method of mass manufacturing of such parts. In this study, the microstructures and mechanical properties of Al-7.0Si-0.4Mg(AC4C) alloy fabricated by squeeze casting process for development of fuel system parts (fuel rail) are investigated. The microstructure of squeeze cast specimen was composed of eutectic structure aluminum solid solution and $Mg_2Si$ precipitates. The tensile strength of as-solid solution treatment Al-7.0Si-0.4Mg alloy was 298.5MPa. It was found that Al-7.0Si-0.4Mg alloy had good corrosion resistance in electrochemical polarization test.

• 동력기계공학회지
• /
• 제18권6호
• /
• pp.29-33
• /
• 2014

The electrochemical characteristics of Al-Si casting alloys (Al-10%Si, Al-9%Si, Al-7%Si) in 3.5% NaCl solution at room temperature was studied using potentiodynamic techniques. The electrochemical values of corrosion potential($E_c$), corrosion current density($I_c$) and corrosion rate(mpy) were examined. The Al-Si alloys had several compounds such as $Mg_2Si$, ${\pi}$-$Al_8Si_6Mg_2Fe$ and $Al_2CuMg$ which could affect corrosion resistance significantly. The potentiodynamic polarization curve exhibited typical active behavior in anodic polarization curve. The major corrosion mechansim for the Al-Si alloys were pitting and grain boundary corrosion. As increasing Si and Cu contents, their corrosion resistance was decreased.

• 한국재료학회지
• /
• 제26권11호
• /
• pp.628-634
• /
• 2016

The cold rolling workability and mechanical properties of two new alloys, designed and cast Al-5.5Mg-2.9Si and Al-7Mg-0.9Zn alloys, were investigated in detail. The two alloy sheets of 4 mm thickness, 30 mm width and 100 mm length were reduced to a thickness of 1 mm by multi-pass rolling at ambient temperature. The rolling workability was better for the Al-7Mg-0.9Zn alloy than for the Al-5.5Mg-2.9Si alloy; in case of the former alloy, edge cracks began to occur at 50% rolling reduction, and their number and length increased with rolling reduction; however, in the latter alloy, the sheets did not have any cracks even at higher rolling reduction. The mechanical properties of tensile strength and elongation were also better in the Al-7Mg-0.9Zn alloy than in Al-5.5Mg-2.9Si alloy. Work hardening ability after cold rolling was also higher in the Al-7Mg-0.9Zn alloy than in the Al-5.5Mg-2.9Si alloy. At the same time, the texture development was very similar for both alloys; typical rolling texture developed in both alloys. These differences in the two alloys can primarily be explained by the existence of precipitates of $Mg_2Si$. It is concluded that the Al-7Mg-0.9Zn alloy is better than the Al-5.5Mg-2.9Si alloy in terms of mechanical properties.

• 한국결정성장학회지
• /
• 제11권3호
• /
• pp.127-131
• /
• 2001

산화물계의 액상소결시 액상량을 변수로 하여 입자형성이 입자성장 거동에 미치는 영향을 고찰하였다. 산화물계 모델로 구형입자의 경우는 MgO$CaMgSiO_{4}$계를 선택하였으며, 각진입자의 경우는 $Al_{2}O_{3}$/ $CaAl_{2}Si_{2}O_{8}$계를 선택하였다. 구형입자인 MgO의 경우 액상량 증가에 따라 입자크기가 감소하였으나,각진입자인 $Al_{2}O_{3}$ 입자의 경우는 계면지배과정에 의해 성장하는 반면, 거친 고상/액상계면을 지닐 것으로 예상되는 구형 MgO입자의 경우는 확산지배과정에 의해 성장하였다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.877-881
• /
• 2006

We obtained sputtering yields for the MgO, $MgAl_2O_4$ and $MgAl_2O_4/MgO$ films using the FIB system. $MgAl_2O_4/MgO$ protective layers have been found to have less $24^{\sim}^30%$ sputtering yield values from 0.24 atoms/ion up to 0.36 atoms/ion than MgO layers with the values from 0.36 atoms/ion up to 0.45 atoms/ion for irradiated $Ga^+$ ion beam whose energies ranged from 10 keV to 14 keV. And $MgAl_2O_4$ layers have been found to have lowest sputtering yield values from 0.88 up to 0.11. It is also found that $MgAl_2O_4/MgO$ and MgO have secondary electron emission $coefficient({\gamma})$ values from 0.09 up to 0.12 for $Ne^+$ ion whose energies ranged from 50 eV to 200 eV.

• Archives of Metallurgy and Materials
• /
• 제66권4호
• /
• pp.959-962
• /
• 2021

In this study, precipitation of Ca in Al-Mg alloys containing a trace of Ca during homogenization was investigated using a transmission electron microscope (TEM) and calculated phase diagrams. TEM result indicated that the Ca-based particles found in the examined sample are Ca₇Mg_7.5Si₁₄. From the calculation of Scheil-Gulliver cooling, it was found that the Ca was formed as Al₄Ca and C36 laves phases with Mg₂Si and Al₁₃Fe₄ from other impurities phase during solidification. No Ca-Mg-Si ternary phase existed at the homogenization temperature in the calculated phase diagram. From the phase diagram of Al-Al₄Ca-Mg₂Si three-phase isothermal at 490℃, it was shown that Ca₇Mg₆Si₁₄ phase co-exists with Al, Mg₂Si and Al₄Ca in the largest region and with only Al and Mg₂Si in Al₄Ca-poor regions. It was thought that the Ca₇Mg₆Si₁₄ ternary phase was formed by the interaction between Mg₂Si and Al₄Ca considering that the segregation can occur throughout the entire microstructures.

• Archives of Metallurgy and Materials
• /
• 제66권3호
• /
• pp.699-702
• /
• 2021

Effect of Cu addition on oxide growth of Al-7 mass%Mg alloy at high temperature was investigated. As-cast microstructures of Al-7 mass%Mg and Al-7 mass%Mg-1 mass%Cu alloys showed α-Al dendrites and area of secondary particles. The 1 mass%Cu addition into Al-7 mass%Mg alloy formed Mg₃₂(Al, Cu)₄₉ ternary phase with β-Al₃Mg₂. The total fraction of two Mg-containing phases in Cu-added alloy was higher than the β-Al₃Mg₂ fraction in Cu-free alloy. From measured weight gains depending on time at 500℃ under an air atmosphere, it was shown that all samples exhibited significant weight gains depending on time. Al-7mass%Mg-1mass%Cu alloy showed the relatively increased oxidation rate when compared with Cu-free alloy. All the oxidized cross-sections throughout the entire oxidation time showed coarse and dark areas regarded as oxides grown from the surface to inside, but bigger oxidized areas were formed in the Al-7mass%Mg-1mass%Cu alloy containing higher fraction of Mg-based phases in the as-cast microstructure. As a result of compositional analysis on the oxide clusters, it was found that the oxide clusters contained Mg-based oxides formed through internal oxidation during a long time exposure to oxidizing environments.