• Korean Journal of Materials Research
• /
• v.8 no.6
• /
• pp.526-531
• /
• 1998

A hydride vapor phase epitaxy (HVPE) method was performed to grow the $10~240\mu{m}$ thick GaN films on (111) spinel $MgAl_2O_4$ substrate. The GaN films on $MgAl_2O_4$ substrate revealed a photoluminescence (PL) characteristics of the impurity doped GaN by the out-diffusion and auto-doping of Mg from $MgAl_2O_4$ substrate during GaN growth. The PL spectrum measured at 10K consists of free and bound excitons related recombination transitions and impurity-related donor-acceptor pair recombination and its phonon replicas. However, the deep-level related yellow band emission was not observed. The peak energy of neutral donor bound excitonic emission and the frequency of Raman $E_2$ mode were exponentially decreased with increasing the GaN thicknesses. and the frequency of E, Raman mode was shifted with the relation of $\Delta$$\omega$=3.93$\sigma$($cm^{-1}$/GPa), where l1 (GPa) is the residual strain in the GaN epilayers.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.2
• /
• pp.105-114
• /
• 2001

$Al_2$$O_3$ coatings were deposited on M2 high speed steels by the plasma enhanced chemical vapor deposition (PECVD) process, using a gas mixture of AlC1$_3$, $H_2$, $CO_2$ and Ar $Al_2$$O_3$ coatings had interference color and showed amorphous phase. $A1_2$X$A1_3$/($Ti_{0.5}$ /$Al_{0.5}$ )N double layer coatings were produced in the sequence of substrate $NH_3$ plasma pretreatment, ($Ti_{0.5}$$Al_{0.5}$)N depoition process, $Al_2$$O_3$ deposition process. $Al_2$ $O_3$/( $Ti_{0.5}$A $l_{0.5}$)N double layer coatings showed NaCl structure in ( $Ti_{0.5}$A $l_{0.5}$)N layer and amorphous phase in A1$_2$ $O_3$ layer. It was shown that $Al_2$ $O_3$ columns continuously grew onto ( $Ti_{0.5}$A $l_{0.5}$)N columns. ( $Ti_{0.5}$A $l_{0.5}$)N single coating and $Al_2$ $O_3$/( $Ti_{0.5}$A $l_{0.5}$)N double layer coating were oxidized at $700^{\circ}C$, 80$0^{\circ}C$, 90$0^{\circ}C$ for 1hr, 3hr in atmosphere. At 80$0^{\circ}C$, single layer coatings were oxidized, which were examined substrate oxide particle. But $Al_2$ $O_3$/ ( $Ti_{0.5}$A $l_{0.5}$)N double layer coatings maintained the asdeposited state. Therefore, $Al_2$ $O_3$/ ( $Ti_{0.5}$A $l_{0.5}$)N double layer coatings have moreexcellent oxidation resistance than ( $Ti_{0.5}$A $l_{0.5}$)N single layer coatings.X> 0.5/)N single layer coatings.s.

• Journal of Welding and Joining
• /
• v.19 no.4
• /
• pp.429-436
• /
• 2001

The effect of welding condition on the microstructures of the weld metal in A7N01 welded by $CO_2$ laser was investigated. The number of ripples was increased with decreasing power and increasing welding speed. In the bead without ripple lines, the subgrain microstructures distribution from the fusion line toward the center of the bead were in the order of cellular, dendritic and equiaxed dendrite. However, in the bead with ripple lines, cellular and dendritic were formed between the fusion boundary and the ripple line. Inaddition, those structures were also observed between the ripple line. Equiaxed dendrites were formed only at the center line region. Cellular and dendritics formed near the ripple line were larger than those formed near the fusion boundary. The cooling rates estimated by the dendrite arm spacing were in the range of 200 to 1150oC/s. Cooling rate was increased with decreasing the power and increasing the welding speed. Mg and Zn segregated at the boundaries of cellulars and dendritics, Mg was segregated more than Zn. The segregation of Mg and Zn decreased with increasing cooling rate. Hardness of the weld metal was lower than that of the base metal in all welding conditions and increased as the cooling rate increased.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.12
• /
• pp.4028-4034
• /
• 2012

Tris(2-phenylphenoxo)aluminum ($(2-PhC_6H_4O)_3Al$) exists as a dimeric form in toluene. When toluene-insoluble anhydrous cobalt acetate is treated with tris(2-phenylphenoxo)aluminum in toluene, the toluene-soluble adduct $(2-PhC_6H_4O)_3Al{\cdot}Co(OAc)_2$ is formed. The 2-phenylphenoxo ligand in the adduct can be replaced with another aryloxo ligand to give (aryloxo)$(2-PhC_6H_4O)_2Al{\cdot}Co(OAc)_2$ (aryloxo = 2-methylphenoxo, 2-isopropylphenoxo, 4-methylphenoxo, 4-isopropylphenoxo, or 4-tert-butylphenoxo). These complexes are active for butadiene polymerization without gel formation when activated with an equivalent amount of $(2-PhC_6H_4O)AlEt_2$ for 2 h. The highest activity, 175 kg/mol-Co (turnover number, 3200) was achieved with $(2-PhC_6H_4O)_3Al{\cdot}Co(OAc)_2$ at $65^{\circ}C$ for 2 h. The microstructure of the polymer chains is mostly trans-1,4-configuration (70-75%) with the remaining being 1,2-vinyl. The cis-1,4-configuration observed by IR is minimal (1-5%). By replacing the 2-phenylpheoxo with a 4-alkylphenoxo ligand, the amount of 1,4-configuration slightly increases, resulting in increase in the endothermic melting signal at $-30{\sim}50^{\circ}C$ in the DSC curve. The molecular weights of the polymers are high ($M_n$: 300000~800000) with a fairly narrow molecular weight distribution ($M_w/M_n$, 2.0-2.7).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2005.08a
• /
• pp.191-191
• /
• 2005

• Applied Chemistry for Engineering
• /
• v.5 no.2
• /
• pp.285-294
• /
• 1994

Some supported gold catalysts were prepared by impregnation and coprecipitation methods. Effect of gold addition and active sloe formation were studied by investigating particle sizes of gold, amounts of oxygen adsorbed, adsorption properties of CO and NO, and reduction and oxidation properties, etc.. The gold particles of the catalyst by impregnation were irregular and very large as 30~100 nm, but those by coprecipitation were uniform and ultra-fine as about 4 nm. On $Au/Al_2O_3$ catalyst, the addition of gold to inactive $Al_2O_3$ caused the decomposition of $N_2O$, and CO was not irreversibly adsorbed while $O_2$ was atomically and irreversibly adsorbed. The adsorption sites of oxygen were attributed to the active sites which were restricted to the circumference of hemispherical gold particle-support interface rather than all atoms on the surface of gold particle. Also, CO was reversibly and irreversibly adsorbed on $Al_2O_3$ at low temperature, and the addition of gold weakened both reversible and irreversible adsorptions. The affinity for CO on $Au/Co_3O_4$ catalyst decreased conspicuously compared to $Co_3O_4$. The effect of gold addition did not appear in reduction step but did remarkably in reoxidation step; the added gold promoted the reoxidation of the reduced cobalt atoms.

• Journal of Environmental Science International
• /
• v.8 no.4
• /
• pp.539-545
• /
• 1999

Dye wastewater was treated by using an electrochemical oxidation process. Various combinations of electrodes such as carbon, Al and Fe were investigated. In this study, electrode material, electrolyte concentration, electrode distance, current density, and pH value were found to have significant effect on both pollutant removal efficiency and current efficiency in electrochemical oxidation process. After electrolysis for 40min with carbon/Al, it was observed that COD, $T-N, NH_{4}^{+}-N$ and color of treated wastwater were reduced from 580mg/$\ell$ to 145mg/$\ell$, 67.2mg/$\ell$ to 26.8mg/$\ell$, 46.8mg/$\ell$ to 1.4mg/$\ell$, and 4200 Pt-Co units to 336 Pt-Co units, respectively. The optimal conditions of the electrooxidation process to treat the wastewater for this study were found to be such : current density ; 16.67mA/$cm^2$, electrode distance ; 2.5cm, pH value ; 5.0 and carbon/Al electrode.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2002.10a
• /
• pp.191.2-191
• /
• 2002

• Journal of Magnetics
• /
• v.4 no.3
• /
• pp.84-87
• /
• 1999

It is shown that progressive crystallization of non-magnetostrictive Co-based metallic glass (VITROVAC 6030) leads to an increase of coercivity by more than three orders of magnitude. The mechani는 responsible for this phenomenon are interpreted showing that the main source for the giant increase of the coercivity is the pinning effect on the domain walls originating from the created crystallites of the size much smaller than the domain width (correlation length for ferromagnetic exchange interactions). It is also shown that gradually devitrified non-magnetostrictive metallic glass is an excellent model material for verification of N el's theory describing the Rayleigh rule.

• Clean Technology
• /
• v.16 no.4
• /
• pp.284-291
• /
• 2010

Nitrous oxide ($N_2O$) is a greenhouse material which is hard to remove. Even with a catalytic process it requires a reaction temperature, at least, higher than 670 K. This study has been performed to see the effects of Ce addition to the mixed oxide catalyst which shows the highest activity in decomposing $N_2O$ completely at temperature as low as 473 K when CO is used as a reducing agent. Mixed metal oxide(MMO) catalyst was made through co-precipitation process with small amount of Ce added to the base components of Co, Al and Rh or Pd. Consequently, the surface area of the catalyst decreased with the contents of Ce, and the catalytic activity of direct decomposition of $N_2O$ also decreased. However, in the presence of CO, the activity was found high enough to compensate the portion of activity decrease by Ce addition, so that it can be ascertained that the catalytic activity and stability can be maintained in the CO involved $N_2O$ reduction system when Ce is added for the physical stability of the catalyst.