• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.179-189
• /
• 2008

The performance of Lean NOx Trap (LNT) based on the catalysts of Pt/K/Ba/$\gamma-Al_2O_3$ with proprietary washcoat formulation is studied using a bench flow reactor system. To investigate the effect of temperature and gas hourly space velocity (GHSV) on the nitrogen oxides (NOx) trapping capacity as well as NOx breakthrough time and final ratio of $NO_2$ to NO of LNT, series of adsorption isotherms are carried out with simulated exhaust gases of the lean burn engines. Since typical operation of LNT requires periodic regeneration with a short rich excursion, where the stored or trapped NOx is released and subsequently reduced to $N_2$, the effect of the duration of lean and rich phase and type of reductants on the NOx conversion is investigated. NOx storage capacity and breakthrough time obtained from adsorption isotherms shows a volcano-type dependence on the temperature with a maximum NOx storage capacity occurring $350^{\circ}C$ and with a maximum breakthrough time occurring $400^{\circ}C$ at all GHSVs investigated in this study. Also, maximum ratio of $NO_2$ to NO is obtained at $400^{\circ}C$ with a GHSV of $75,000\;hr^{-1}$ Lean/rich cycle of 100 s lean and 5 s rich used with a concentration of 1.33% of $H_2$ and 4% of CO in the rich phase is found to be optimum at operating temperature of $350^{\circ}C$ and a GHSV of $50,000\;hr^{-1}$.

• Journal of the Korean Ceramic Society
• /
• v.41 no.5
• /
• pp.395-400
• /
• 2004

The effects of compositions of binders on the rheological properties of mixtures and the preparation conditions on the formation of defects and the debinding characteristics of compacts for the injection molding of ceramic powders (65 wt% aluminaㆍ35 wt% feldspar) were studied. Ceramic powders were coated with 2 wt% of stearic acid and then mixed with 15, 20, and 25 wt% of Paraffin Wax (PW) and High Density Polyethylene (HDPE) as binders at $160^{\circ}C$ for 2 h. Rheological properties were investigated by using capillary rheometer. Apparent viscosities of mixtures were 80∼300 Paㆍs at 1,000$s^{-1}$ of a shear rate, it was good for the injection molding and depending on the compositions of binders. Short shot was formed at 15H5P5 (the ratio of HDPE : PW=5 : 5 in 15 wt% of binders) compacts without injection pressures and any noticeable defects were not formed at 45 kgf/$cm^{2}$ in 20H5P5 compacts. PW and HDPE were removed by the solvent extraction and thermal debinding method. Thermal debinding of HDPE at $450^{\circ}C$ for 5 h, which followed the extraction of PW was using n-heptane solvent at $70^{\circ}C$ for 5 h. Continuous pores in compacts, which facilitate the removal of HDPE by the thermal debinding, were found to form in the compacts when PW was removed by the solvent extraction. The optimum composition of binder at which binder was removed by thermal debinding without defects while maintaining the compact strength was 20H5P5. Bulk density, porosity and 3-point bending strength of 20H5P5 compact sintered at 1,30$0^{\circ}C$ for 5 h were 2.8, < 3%, and 2,400 kgf/$cm^{2}$, respectively, and can be used as a structural materials.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1B
• /
• pp.51-60
• /
• 2006

Water quality improvement in mattress/filter system using porous material like slag from industrial activity and zeolite that has been studied for environment improvement and pollution abatement is very useful in polluted stagnant stream channel. Slag is consisted of CaO, $SiO_2$, $Al_2O_3$ and $Fe_2O_3$. Slag with large specific surface area of porosity has been used such as sludge settling and adsorptive materials. Because slag is porous, it can be used for purification filter. As slag is used as filled materials of mattress/filter system and the system has good advantages for the waste water treatment, water recycling, and the improvement of water quality at the same time and so on. Because zeolite has much advantage of cation exchange, adsorption, catalyst and dehydration characteristics, It is used for environment improvement of livestock farms, treatment of artificial sewage and waste water, improvement of drinking water quality, radioactive waste disposal and radioactive material pollution control. In this study, according to verifying effects of water quality improvement of fill materials by porosity that 38.6%, 45.8% and 49.8% respectively in the stagnant stream channel, water quality monitoring of inflow and outflow was conducted on pH, DO, BOD, COD, SS, T-N and T-P. Mattress/filter system was able to accelerate water quality improvement by biofilter as waste water flows through gap of mattress/filter fill materials and by contact catalysis, absorption, catabolism by biofilm. Mattress/filter system used slag and zeolite forms biofilm easily and accelerates adsorption of organic matter. As a result, mattress/filter system increases water self-purification and accelerates water quality improvement available for stream water clean-up.

• Journal of Biomedical Engineering Research
• /
• v.29 no.2
• /
• pp.132-138
• /
• 2008

We investigated the biomechanical properties of a newly designed self-expansion type anterior cruciate ligament (ACL) anchor. The ACL anchor consists of the ring section giving the elastic force, the wedge for maintaining in contact with the femur tunnel wall and the link suspending hamstring graft or artificial ligament. The main design parameters that determine the performance of this device were the expansion angle (${\theta}$) and the thickness ($t_R$). The Ti6Al4V anchors were heated after inserting in a jig for 1 hour at $800^{\circ}C$ in a protective argon gas atmosphere and allowed to cool to room temperature in the furnace. In order to investigate the influence of the expansion angle and the thickness of the ring on the biomechanical properties of the anchor, the maximum pull-out load, stiffness and slippage of the ACL anchor were measured using the pull-out tester, and statistical analyses were also executed. The present results showed that the design parameters gave a significant effect on the performance of the self- expansion type of anchor. The pull-out load of the ACL anchors significantly increased as the thickness of the ring section was increased, having a similar trend for both expansion angles. The ACL anchor showed about 2.5 times higher values of the pull-out load than that of the minimum load (500N)required for the "accelerated rehabilitation". The optimum ${\theta}$ and $t_R$ values of this ACL anchor were suggested to have sufficient resistance against the pull-out force, high stiffness and relatively low slippage after ACL reconstruction.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.2
• /
• pp.639-644
• /
• 2011

A simple and highly sensitive chemiluminescence method to determine norfloxacin (NFLX) has been proposed by measuring the chemiluminescence (CL) intensities using a flow injection (FI) system. The CL intensity of the luminol-$H_2O_2$ system is strongly enhanced by the addition of Cu (II) in alkaline condition. The CL intensity is substantially increased after the injection of NFLX into the luminol-$H_2O_2$-Cu (II) system. The enhancement effect is attributed to a catalytic effect of Cu (II) due to the interaction with NFLX which forms a complex with the catalyst. Under the optimal conditions, the sensitizing effect of the CL intensity is proportional to the concentration of NFLX in the range of $1.5{\times}10^{-9}-5.9{\times}10^{-7}molL^{-1}$ (r = 0.9994) with a detection limit ($3{\sigma}$) of $2.98{\times}10^{-10}molL^{-1}$. The proposed method had good reproducibility with the relative standard deviation (RSD, n = 5) of 1.6% for $1{\times}10^{-7}molL^{-1}$ of NFLX. The possible reaction mechanism of the CL reaction is also discussed. This method has been successfully applied for the determination of trace amount of NFLX in pharmaceutical preparations and serum samples.

• Journal of Korea Foundry Society
• /
• v.36 no.6
• /
• pp.202-207
• /
• 2016

The effects of Fe and Si additions on the microstructures and mechanical properties of aluminum bronze have been investigated. In a bar-type specimen cast in a die mold, the addition of Fe promoted the dendritic solidification of the ${\alpha}$ phase. The hardness values increased slightly in the Fe-added specimen with heat treatment, while these values was increased significantly in the specimens with Si or with combined additions of Fe and Si. When a centrifugal casting bush with combined addition of Fe and Si was heat treated, the FeSi compound within the matrix was finely dispersed, and was observed to be the origin of cup-cone type conical dimple failure in the tensile fracture surface. The mechanical properties of the heat treated centrifugal casting bushes, whose nominal alloy compositions were (Cu-7.0Al-0.8Fe-3.0Si)wt%, exhibited tensile strength of $703-781N/mm^2$, elongation of 6.6-11.7% and hardness of Hv 222.6-249.2. These high values of strength and elongation were attributed to the strengthening of the matrix due to the combined addition of Fe and Si, and to precipitation of fine the FeSi compound.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.4
• /
• pp.312-317
• /
• 2005

The objectives of this paper are to study the absorption characteristics of $NH_3$ bubbles in the binary nanofluids and to quantify the effects of surfactants and nano-particles on the bubble absorption performance. 2-Ethyl-1-Hexanol, n-Octanol, and 2-Octanol are used as the surfactants and nano-sized $Al_{2}O_3$ and Cu particles are added to make the binary nanofluids into $NH_3/H_{2}O$ solution. The concentration of $NH_3$ solution ($x_s$), the concentration of surfactants ($x_{SA}$), and the mass fraction of nano-particles ($w_{np}$) are considered as key parameters. The experimented ranges of $x_s,\;x_{SA},\;and\;w_{np}$ are $0{\sim}17.92\%,\;0{\sim}1,500\;ppm\;and\;0{\sim}0.2\%$, respectively. The absorption rates are calculated by measuring initial and final weights of test section and exposed time. In addition, the bubble absorption processes are visualized using the shadow graphic method. The results show that the absorption performance is significantly enhanced up to 4 times by adding the surfactants and up to 3 times in the binary nanofluids.

• The Bulletin of The Korean Astronomical Society
• /
• v.43 no.1
• /
• pp.53.1-53.1
• /
• 2018

During a major solar eruption, the erupting plasma is possibly out of the equilibrium ionization state because of its rapid heating or cooling. The non-equilibrium ionization process is important in a rapidly evolving system where the thermodynamical time scale is shorter than the ionization or recombination time scales. We investigate the effects of non-equilibrium ionization on EUV and X-ray observations by the Atmospheric Imaging Assembly (AIA) on board Solar Dynamic Observatory and X-ray Telescope (XRT) on board Hinode. For the investigation, first, we find the emissivities for all the lines of ions of elements using CHIANTI 8.07, and then we find the temperature responses multiplying the emissivities by the effective area for each AIA and XRT passband. Second, we obtain the ion fractions using a time-dependent ionization model (Shen et al. 2015), which uses an eigenvalue method, for all the lines of ion, as a function of temperature, and a characteristic time scale, $n_et$, where $n_e$ and t are density and time, respectively. Lastly, the ion fractions are multiplied to the temperature response for each passband, which results in a 2D grid for each combination of temperature and the characteristic time scale. This is the set of passband responses for plasma that is rapidly ionized in a current sheet or a shock. We investigate an observed event which has a relatively large uncertainty in an analysis using a differential emission measure method assuming equilibrium ionization state. We verify whether the observed coronal plasmas are in non-equilibrium or equilibrium ionization state using the passband responses.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.71-74
• /
• 1996

Ta$_2$O$_{5}$ film ale recognized as promising capacitor dielectric for future DRAM\`s. The electrical properties of Ta$_2$O$_{5}$films greatly depend on the heating condition. In the practical fabrication process, several annealing process, such as the annealing of Al in H$_2$(about 40$0^{\circ}C$) and reflow of BPSG (borophosphosilicate glass) film in $N_2$(about 80$0^{\circ}C$), exist after deposition of Ta$_2$O$_{5}$ film. In this paper, we describe the temperature effect on the electrical properties of W/Ta$_2$O$_{5}$/Si structure. The thin film of Ta$_2$O$_{5}$ and tungsten have been deposited on p-si(100) wafer using the sputtering system. The heating temperature was varied from 500 to 90$0^{\circ}C$ in $N_2$for 30min and The degree of temperature is 100\`C. In a log(J/E$^2$) Vs 1/E plot of typical I-V data, we find a linear relationship for the temperature of 500, $600^{\circ}C$ and as deposition. This could indicate Fowler-Nordheim tunneling as the dominant mode of current transports. However, we can not find a linear relationship for the temperature above $700^{\circ}C$. This could not indicate Fowler-Nordheim tunneling as the dominant mode of current transport. The high frequency (1MHz) capacitance-voltage (C-V) of W/Ta$_2$O$_{5}$/Si Capacitor were investigated on the basis of shift in the threshold voltage and dielectric constant. The magnitude of the threshold voltage and dielectric constant depends on the heating temperature, and increases with heating temperature.temperature.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.1
• /
• pp.1-6
• /
• 2008

Thermoelectric properties of calcium cobalt layer structure oxide system, $Ca_3Co_2O_6$ and $Ca_3Co_4O_9$ were investigated at the temperature range of 300 to 1000K for the application of thermoelectric generation. In the composition, the Ca site was partially substituted with Bi, Sr, La, K and the Co site was partially substituted with Mn, Fe, Ni, Cu, Zn. The thermoelectric properties of Bi substituted $Ca_3Co_4O_9$. $Ca_{2.7}Bi_{0.3}Co_4O_9$ for electrical conductivity, Seebeck coefficient and power factor were $85.4({\Omega}$cm)^{-l}, $176.2{\mu}V/K$ and $265.2{\mu}W/K^m$, respectively. The unit thermoelectric couple was fabricated with the p-type of $Ca_{2.7}Bi_{0.3}Co_4O_9$ and n-type ($Zn_{0.98}Al_{0.02}$)O thermoelectrics whose figure-of-merit(Z) were $0.87{\times}10^{-4}/K$ and $0.41{\times}10^4/K$, respectively. The generated thermoelectric power was about 30mV at the temperature difference of 120K in the unit thermoelectric couple.