• 한국정밀공학회지
• /
• 제5권4호
• /
• pp.48-58
• /
• 1988

This study was undertaken to observe the formation behavior of ferro- magnetic phase in Mn-Al-Cu Alloys. The alloy selected for this investigation was 70% Mn-29% Al-1% Cu. This pre-allyed pig was prepared to the cylinderical castings using an Induction furnace after homogenizing at $1100^{\circ}C$ for 2hr, the specimens were cooled by cooling methods. Subwequent isothermal heat treatments were followed at $550^{\circ}C$ for various periods of time at predetermined(1-1000min). The formation behavior of ferromagnetic phase was investigated by measurements of magnetic properties of the specimens at each stage of heat treatment, and optical microscopic esamination and X-Ray diffraction analyses were also employed. By this basic experimental results, the conclusions are as follows 1) In order to obtain much amount of ferromagnetic phase, the optimum average cooling rate was about 7.35-$16.4^{\circ}C$/sec($1100^{\circ}C$-$600^{\circ}C$). 2) We verified the decomposition of {\tau} phase to {\beta} -Mn and {\gamma} , as the specimens were homogenized at $1100^{\circ}C$ for 12hr, then heat-treased at $550^{\circ}C$ for 1-1000min. 3) A condition of optimum heat treatments in Mn-Al-Cu permanent mag-netic alloys showed that after homogenizing at $1100^{\circ}C$ for 2hr, the speciments were cooled in air or furnace(A) and subsequent heat treatments at $550^{\circ}C$ for 1-30min. The maximum magnetic properties were measured as follows: Air cooling; Br=1200(Gause), bHc=100(oe), (BH)max=0.07(MGOe) Furnace cooling(A);Br=950(Gauss), bhe=80(Oe), (BH)max=0.05(MGOe)

• 대한환경공학회지
• /
• 제33권2호
• /
• pp.93-102
• /
• 2011

본 연구에서는 부산신항만 준설퇴적물에 포함된 중금속의 총농도, 이동성, 생체이용률, 독성을 알아보기 위하여 총함량분석과 연속추출실험을 실시하였다. 준설퇴적물의 중금속 총농도는 다음과 같이 비교적 낮았다: Al (2.36~2.96 wt.%), As (1.6~3.3 mg/kg), Ba (30.0~33.8 mg/kg), Cd (0.12~0.18 mg/kg), Cr (27.5~35.0 mg/kg), Cu (11.3~15.0 mg/kg), Fe (2.91~3.51 wt.%), Mn (324~408 mg/kg), Ni (18.8~23.8 mg/kg), Pb (23.8~31.3 mg/kg), Zn (70.0~86.3 mg/kg). 또한 대부분의 중금속이 residual fraction으로 존재하였는데, 이는 오염원이 자연발생적일 가능성이 높음을 의미한다: Al (87.5~95.9%), As (74.1~93.8%), Ba (71.8~77.6%), Cr (69.5~94.3%), Cu (50.0~78.7%), Fe (70.8~87.6%), Ni (64.5~75.3%), Pb (53.4~64.3%), Zn (62.5~81.7%). 반면에 Cd과 Mn은 주로 non-residual fraction으로 존재했다. 준설퇴적물의 유해중금속 농도가 낮고 residual fraction 비율이 높기 때문에, 이를 벽돌, 도로포장재료 등으로 재활용하는 것이 가능하다고 사료된다.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 1999년도 High Temperature Superconductivity Vol.IX
• /
• pp.185-188
• /
• 1999

Biepitaxial Y$_1Ba_2Cu_3O_{7-x}$ (YBCO) and La$_{0.2}Sr_{0.8}MnO_3$ (LSMO) thin films have been prepared on SrTiO$_3$ buffer layer and MgO seed layer grown on Al$_2O_3$(11${\bar{2}}$0)substrates by dc-sputtering with hollow cylindrical targets, respectively. We charaterized Josephson properties and significantly large magnetoresistance in YBCO and LSMO films with 45$^{\circ}$ grain boundary junction, respectively. The observed working voltage (I$_cR_n$) at 77 K in grain boundary junction was below 10${\mu}$V, which is typical I$_cR_n$ value of single biepitaxial Josephson junction. The field magnetoresistance ratio (MR) of LSMO grain boundary juncoon at 77K was enhanced to 13%, which it was significant MR value with high magnetic field sensitivity at a low field of 250 Oe. These results indicate that inserting the insulating layer instead of the grain boundary layer with metallic phase can be possible to apply a new SIS Josephson junction and a novel magnetic device using spin-polarized tunneling junction.

• 한국수소및신에너지학회논문집
• /
• 제6권1호
• /
• pp.35-41
• /
• 1995

The MmNi-based alloy electrode was studied for use as a negative electrode in Ni-MH battery. Alloys with $MmNi_5-_xM_x$(M=Co,Al,Mn) composition were synthesized, and their electrode charateristics of activation rate, temperature dependence, electrode capacity and cycle life were investigated. With increasing Al content and decreasing Mn content in the alloys, the discharge capacity increased while the cycle life decreased. As x in $MmNi_5-_xM_x$ increased from 1.5 to 2.0, decreasing the Ni content, the discharge capacity, the low temperature property and the rate capability decreased. However its cycle life was improved. Increasing Co content resulted in a prolonged cycle life and decrease of high rate discharge capacity. It can be concluded that the most promising alloy in view of discharge capacity and cycle life is $MmNi_{3.5}Co_{0.7}Al_{0.5}Mn_{0.3}$.

• 한국세라믹학회지
• /
• 제26권3호
• /
• pp.347-360
• /
• 1989

Spinel, mullite, forsterite and cordierite composition powders were synthesized from Mg(NO3)2.6H2O, Al(NO3)3.9H2O and SiCl4-ethanol solution by spray pyrolysis method and the sinterability of these powders were investigated. The bulk density of spinel and mullite specimens sintered at 1,$700^{\circ}C$ for 1hr was 3.56g/㎤(99.5% relative density) and 3.16g/㎤(99.7% relative density), respectively. (Green compacts were made from powders prepared at 1,00$0^{\circ}C$). The bulk density of forsterite and cordierite specimens sintered at 1,480 and 1,40$0^{\circ}C$ for 2hrs were 3.217 and 2.155g/㎤, respectively. (Green compacts were made from powders prepared at 1,00$0^{\circ}C$). The constituent compositions of spinel and mullite specimens sintered at 1,$700^{\circ}C$ for 1hr were 27.5wt% MgO and 70.5wt% Al2O3, respectively. Vickers microhardness and fracture toughness of spinel sintered at the above condition were 13.7GPa and 2.6MN.m3/2, respectively, and room temperature bending strength, 425MPa, was nearly maintained even at the elevated temperature. In the case ofmullite specimens, those values were 13.5GPa, 2.2MN/m3/2 and 430MPa, respectively.

• 한국군사과학기술학회지
• /
• 제7권1호
• /
• pp.47-58
• /
• 2004

Loss factors of A356, Mn-Cu alloy and aluminum matrix composites reinforced with $SiC_p$ and Ni-coated graphite particles at various contents have been investigated using clamped-free cantilever beam method. The loss factors of half-power bandwidth of the specimens were measured over a wide range of frequencies from 50 to 3300Hz. Among the specimens, Al-10%$SiC_p$-10%$C_p$ showed the highest loss factor at the mode I, while Mn-Cu alloy showed the highest loss factors at the modes II and III. Consequently, at the mode I the Al-10%$SiC_p$--10%$C_p$ showed the loss factor of 0.00093, which is 2.64 and 1.58 times higher than those of A356 and Mn-Cu alloy, respectively.

• 한국해양학회지:바다
• /
• 제20권4호
• /
• pp.159-168
• /
• 2015

한국 남서해 연안의 도암만에서 44개 표층퇴적물을 채취하여 총유기탄소(TOC), 총질소(TN) 및 중금속(Al, Fe, Mn, Cr, Cu, Ni, Pb, Zn)을 분석하였으며, 11개 시료에 대해서는 화학적 존재형태별 분석을 병행하였다. TOC(0.32~3.10%), TN(0.03~0.26%)은 주변 해역의 평균 수준이었고, C/N 비(7.9~11.9)에 근거할 때 육상기원 유기물의 영향이 반영된 일부 지역이 구분되었다. 중금속 함량은 대부분의 정점에서 해양퇴적물 주의기준(TEL) 이하였고, 화학적 존재형태별 함량은 광물격자부분에서 Cr, Cu, Ni 등이, 비광물격자부분에서 Mn, Pb가 총량의 절반을 상회하였다. 연구지역의 중금속 배경농도를 누적빈도곡선과 선형회귀분석에 의해 추정한 결과 Cu=11.8, Ni=23.1, Pb=26.8, Zn=76.6, Cr=56.7, Mn=585 mg/kg으로 계산되었으며, 이를 바탕으로 한 농축지수($I_{geo}$)에 근거해 국지적인 Mn 농축의 징후를 확인하였다. 그러나 농축지수와 존재형태비를 고려할 때 Zn, Pb도 환경변화에 따른 용출 가능성이 추정되었다.

• 대한전자공학회논문지
• /
• 제22권6호
• /
• pp.7-12
• /
• 1985

Oxygen-active 금속, 천이금속 및 oxygen-noble 금속, 즉, Al, Ti, Mn, Ni 그리고 Cuㄹ박막의 광투과율을 조사하였다. Slide-glass 위에 $6{\times}10^{-5}$ ~ $2{\times}10^{-4}$ mbr 압력범위와 0.5 ~ $2{\AA}$/sec 의 증착속도 범위에서 두께를 $85{\AA}$내외로 하여 증착하였다. 증착속도와 진공도는 금속박막의 광학적 성질에 큰 영향을 미치며 이는 주로 산소개입에 의한 것임을 알 수 있었다. 특히 광투과율이 매우 낮다고 알려진 산소와의 친화력이 강한 금속, 즉, Al, Ti, Cr 그리고 Ni의 광투과율을 저 진공도나 느린 증착속도에 의한 증착공정으로 상당히 향상시킬 수 있었다.

• 한국지구과학회지
• /
• 제32권7호
• /
• pp.707-718
• /
• 2011

보성-화순지역 하상퇴적물에 대한 지질집단별 자연배경치와 지구화학적 특성에 대해 연구하였다. 이를 위해 1차 수계를 따라 하상퇴적물시료 186개를 채취하였고, 실험실에서 자연건조 시킨 후, XRF, ICP-AES, NAA분석을 실시하였다. 하상퇴적물의 지질집단별 자연배경치와 지구화학적 특성을 알기 위해, 시료를 화강암질편마암(GGn)지역과 반상변정질편마암(PGn)지역으로 분리하였다. 화강암질편마암지역의 주성분원소 함량은 $SiO_2$ 45.5-73.09 wt.%, $Al_2O_3$ 12-20.76 wt.%, $Fe_2O_3$(T) 3.72-8.85 wt.%, $K_2O$ 2.38-4.2 wt.%, MgO 0.75-2.77 wt.%, $Na_2O$ 0.78-1.88 wt.%, CaO 0.27-2.1 wt.%, $TiO_2$ 0.56-1.72 wt.%, $P_2O_5$ 0.06-0.73 wt.% and MnO 0.03-0.95 wt.%이고 반상변정질편마암지역의 주성분원소 함량은 $SiO_2$ 43.74-70.71 wt.%, $Al_2O_3$ 11.54-25.05 wt.%, $Fe_2O_3$(T) 3.44-13.46 wt.%, $K_2O$ 2.08-3.86 wt.%, MgO 0.65-2.99 wt.%, $Na_2O$ 0.63-1.7 wt.%, CaO 0.35-2.07 wt.%, $TiO_2$ 0.68-4.17wt.%, $P_2O_5$ 0.1-0.31 wt.% and MnO 0.07-0.33 wt.%이다. 화강암질편마암지역 하상퇴적물의 위해원소 함량은 크롬 41.7-242 ppm, 코발트 7.6-25.1 ppm, 니켈 12-61 ppm, 구리 10-47 ppm, 아연 48.5-412 ppm, 납 17-215 ppm이고 반상변정질편마암지역은 크롬 29.6-454 ppm, 코발트 5.9-53.7 ppm, 니켈 8.7-287 ppm, 구리 6.4-134 ppm, 아연 43.6-370 ppm, 납 15-37 ppm이다. 화강암질편마암지역에서 크롬은 MgO와 코발트는 $Al_2O_3$, $Fe_2O_3$(T), MgO와 니켈은 $Fe_2O_3$(T), CaO, MgO와 높은 상관성을 가지나, 구리, 아연, 납은 비교적 낮은 상관성을 보였다. 반상변정질편마암지역에서 일반적으로 크롬, 코발트, 니켈, 구리는 주성분원소와 대부분 높은 상관성을 보였으나, 아연과 납은 낮은 상관성을 보였다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제24권2호
• /
• pp.19-22
• /
• 2022

We studied the effect of substrate-induced strain state on the superconducting transition in GdBa₂Cu₃O_7-x(GdBCO)/La_0.7Sr_0.3MnO₃ (LSMO) bilayers deposited on a LaAlO₃ (LAO) substrate. The stain state of LSMO is controlled by increasing the thickness from 20 nm to 80 nm. Analyses on the extended X-ray absorption fine structure (EXAFS) measurements reveal difference in the direction of MnO₆ octahedral distortion depending on the LSMO thickness, which leads to a difference in anisotropy of magnetization of LSMO layer. The superconducting transitions of our system are strongly correlated with the magnetic anisotropy accompanied by the MnO₆ octahedron distortion in a specific direction. This result suggests the possibility of improving the superconducting transition in the GdBCO/LSMO bilayer system by controlling the degree of competition between superconductivity and ferromagnetism via adjusting strain state in the LSMO layer.