The trend to thinner crystalline silicon solar wafers in production of solar cells investigates re-evolution of back surface field (BSF) formation. We have studied mechanisms of back contact formation in Al evaporation and screen printed Al paste for Si solar cells by TEM analysis. We observed that Si diffuse into Al during heat up. The Si diffusion process made vacancies in Si wafer. The Al began to seep into the Si wafer (Al spike). During heat down, the Al spike were shrink which causes the doped region (BSF).
Surface recombination loss should be reduced for high efficiency of solar cells. To reduce this loss, the BSF (back surface field) is used. The BSF on the back of the p-type wafer forms a p+layer, which prevents the activity of electrons of the p-area for the rear recombination. As a result, the leakage current is reduced and the rear-contact has a good Ohmic contact. Therefore, the open-circuit-voltage (Voc) and fill factor (FF) of solar cells are increased. This paper investigates the formation of the rear contact process by comparing aluminum-paste (Al-paste) with pure aluminum-metal(99.9%). Under the vacuum evaporation process, pure aluminum-metal(99.9%) provides high conductivity and low contact resistance of $4.2\;m{\Omega}cm$, but It is difficult to apply the standard industrial process to it because high vacuum is needed, and it's more expensive than the commercial equipment. On the other hand, using the Al-paste process by screen printing is simple for the formation of metal contact, and it is possible to produce the standard industrial process. However, Al-paste used in screen printing is lower than the conductivity of pure aluminum-metal(99.9) because of its mass glass frit. In this study, contact resistances were measured by a 4-point probe. The contact resistance of pure aluminum-metal was $4.2\;m{\Omega}cm$ and that of Al-paste was $35.69\;m{\Omega}cm$. Then the rear contact was analyzed by scanning electron microscope (SEM).
최근 태양전지의 후면에서 통상적으로 사용되는 Al을 이용한 후면의 BSF형성과 그에 관한 연구보다 계면의 recombination을 줄이기 위하여 passivation 특성이 좋은 층을 후면에 형성하고 국부적으로 BSF를 형성하는 back contact을 형성하여 특성을 향상시키는 연구가 많이 이루어지고 있다. 본 연구는 이러한 local back contact을 boron-BSF를 이용하여 형성하고 passivation layer는 oxide를 이용한 구조를 SILVACO 2-dimension simulation을 이용하여 그 특성을 분석하였다. Boron-local back contact 구조에서 boron-BSF의 doping concentration, depth, lateral width, boron-BSF spacing 가변을 통해 태양전지의 특성변화에 대해서 spectrum response를 통한 QE 분석 및 I-V를 분석하여 최적화하였다.
최근 결정질 실리콘 태양전지 분야에서는 태양전지의 Voc와 Isc의 증가를 통한 효율 향상을 목적으로 후면 passivation 박막에 대한 연구가 활발하게 진행되고 있다. Local-Back Contact Cell은 최적화된 후면 passivation 박막을 이용한 태양전지 제조방법이다. 본 연구에서는 고효율의 LBC 태양전지 개발을 위해 Rapid Thermal Oxide(RTO)를 이용한 후면 passivation 박막에 screen printing을 이용한 point contact 구조의 LBC 태양전지를 제작하고 그 특성을 분석하였다. 본 연구에 사용된 RTO 박막은 O2와 N2, 2L/min의 조건에서 $850^{\circ}C$에서 3분 동안 열처리하여 성장시켰다. 이렇게 성장된 박막은 3nm의 두께로 형성되어 passivation 효과를 나타내었으며, carrier lifetime 측정 결과 37.8us의 값을 나타냈다. 전면 ARC형성을 위해 RTO 박막 위에 PECVD를 이용하여 SiNx passivation 처리를 하였고, 그 결과 carrier lifetime은 49.1us까지 향상하였다. 후면의 전극 형성을 위해 screen printing 방법으로 Al point contact을 형성하여 local 한 BSF를 형성 시켰으며, 이후 후면 전극 연결을 위한 방법으로 300nm의 두께로 full Al evaporation 공정을 진행 하였다. 결과적으로 RTO 후면 passivation 박막에 Al point contact 형성을 통해 제작된 태양전지는, Suns-Voc 579mV, FF 82.3%, 16.7%의 효율을 달성하였다.
There are some methods for increasing efficiency of crystalline silicon solar cells. Among them, It is important to reduce the recombination loss of surface for high efficiency. In order to reduce recombination loss is a way to use the BSF(Back Surface Field). The BSF on the back of the p-type wafer forms a p+layer. so, it is prevented to act electrons of the p-area for the rear recombination. As a result, the leakage current is reduced and the rear-contact has a good Ohmic contact. therefore, open-circuit-voltage and Fill factor(FF) of solar cells are increased. This paper investigates the formation of rear contact process comparing Aluminum-paste(Al-paste) with Aluminum-Metal(99.9%). It is shown that the Aluminum-Metal provides high conductivity and low contact resistance of $21.35m{\Omega}cm$ using the Vacuum evaporation process but, it is difficult to apply the standard industrial process because high Vacuum is needed and it costs a tremendous amount more than Al-paste. On the other hand, using the Al-paste process by screen printing is simple for formation of metal contact and it is possible to produce the standard industrial process. however, it is lower than Aluminum-Metal(99.9) of conductivity because of including mass glass frit. In this study, contact resistances were measured by 4-point prove. each of contact resistances is $21.35m{\Omega}cm$ of Aluminum-Metal and $0.69m{\Omega}cm$ of Al-paste. and then rear contact have been analyzed by Scanning Electron Microscopy(SEM).
결정질 태양전지 제작에서, passavtion은 표면의 반사도를 줄여주는 반사 방지막의 역할과 표면의 dangling bond를 감소시켜, 표면 재결합 속도를 줄이고 minority carrier lifetime을 증가하는 데 큰 영향을 미친다. 그렇기 때문에 저가형 고효율 태양전지 제작에서 우수한 특성을 가지는 passivation막은 매우 중요한 이슈이다. 본 연구에서는 LBC(local back contact) 구조를 가지는 단결정 태양전지 후면에, 기존의 Full Al-BSF의 passivation 막을 SiNx와 ONO passivation 막으로 각각 대체하여, LBC 구조에서 더 적합한 passivation 막을 찾고자 하였다. SiNx와 ONO passivation 막은 단결정 LBC 구조 태양전지 후면에 각각 형성되었고 $800^{\circ}C$, 20 sec 조건으로 소성되었다. 실험결과는 minority carrier lifetime과 surface recombination velocity로 관찰하였다. 그 결과, SiNx passivation 막의 표면 재결합 속도는 29.7cm/s이고, ONO passivation 막의 표면 재결합 속도는 24.5cm/s로, Full Al-BSF 표면 재결합 속도 750cm/s에 비해 더 적합한 passivation 막으로 확인할 수 있었다. 결과적으로 SiNx,ONO passivation 막이 Full Al-BSF보다 전극에 수집되는 캐리어의 양이 많아짐에 따라 효율향상을 가져올 수 있을 것이다.
In rearpoint contact solar cell and the PERC (passivated emitter rear contact) type cell, surfaces were passivated by SiO2 or Al2O3 to increase solar cell efficiency. Therefore, we have investigated the effect of surface passivation for crystalline silicon solarcell using mass-production atomic layer deposited (ALD) Al2O3. The patttern which consists of cylinders with 100um diameter and 5um height was formed by PR patterning on Si (100) substrate and then Al2O3 of about 10nm and 20nm thickness was deposited by ALD. The pattern in 10 nm Al2O3 film was removed by dipping in aceton solution for about 10 min but the pattern in 20 nm Al2O3 film was not. The influences of process temperature and heat treatment were investigated using microwave photoconductance decay (PCD) and Quasi-Steady-State photoconductance (QSSPC). The solar cell process used in this work combines the advantage of using the applicability of a selective deposition associated with a ALD passivation and the use of low-cost screen print for the contacts formation.
최근 태양전지에 대한 연구가 본격적으로 진행 중인 가운데 Local back contact 태양전지에 대한 연구가 새로운 이슈로 떠오르고 있다. LBC 구조의 태양전지는 후면 passivation에 대한 최적화 공정이 가장 중요하다. 후면 passivation으로 사용되는 물질로는 $SiO_2$, SiNx, $Al_2O_3$ 등의 산화막이 대표적이다. 본 연구에서는 LBC 구조 태양전지의 후면 passivation 박막으로 사용되는 $SiO_2$ 산화막의 공정가변에 따른 박막의 특성을 비교 분석하였다. $SiO_2$ 성장은 RTP를 사용하였다. 성장 온도 $850^{\circ}C$의 온도에서 진행하였으며, 4L/min의 $O_2$분위기에서 진행하였다. 공정 시간 5분 일 때 12.5nm, 15분 일 때 21.7nm의 두께의 박막을 성장 시킬 수 있었다. Carrier lifetime 확인 결과 박막의 두께가 얇을수록 lifetime이 향상함을 확인 할 수 있었고, C-V 측정을 통한 charge 비교를 통해 두께가 얇은 박막 일수록 더 적은 positive charge를 갖고있는 것을 확인 할 수 있었으며 이를 통해 passivation 효과가 우수함을 확인 할 수 있었다.
일반적으로 screen printing 전극은 양산용 태양전지에 많이 응용되고 있다. 이것은 공정이 진공상태 내에서 이루어지지 않으므로 비교적 간단하게 증착 가능하고, co-firing으로 인한 공정단계의 함축과, 기판의 화학적인 오염이 적으며, 시료를 용도에 따라 다양하게 선택적으로 사용할 수 있고, 많은 수량의 태양전지에 전극을 저비용으로 빠르게 형성할 수 있기에 throughput 이 높은 장점이 있다. 하지만 lithography에 의한 전극보다 저항이 높고, uniformity가 낮은 단점이 있다. 본 연구에서는 Ag 전면전극과 Al 후면전극을 형성하고 conventional furnace에서 co-firing하여 열처리조건에 따라서 전극이 최적화된 가장 낮은 저항을 갖도록 하여 단점을 개선하여 보았다.
결정질 실리콘 태양전지의 알루미늄 후면전극이 패시베이션층의 공극을 통하여 확산됨으로써 국부 후면전계(local back surface field)가 형성되는 후면 점접촉 구조를 제조하였으며, 이에 대한 공정조건 및 특성을 연구하였다. 후면 패시베이션층은 실리콘 기판과 금속전극사이에 삽입됨으로써 표면 재결합속도를 낮추고, 후면 반사도를 높여 광흡수 경로를 증가시킬 수 있다. 고가의 사진식각기술 대신에 저가의 단순한 공정인 레이저 식각기술을 사용하여 후면 패시베이션층에 균일하고 잘 정렬된 공극 패턴을 형성할 수 있었다. 레이저 식각 조건 및 소성조건에 따른 Al 확산 국부 후면전계의 단면 형상을 주사전자현미경(SEM)을 사용하여 관찰하였으며 이에 대한 전기적, 광학적 특성 변화를 조사하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.