• Korean Journal of Materials Research
• /
• v.18 no.1
• /
• pp.51-56
• /
• 2008

The crystal structures and morphologies of precipitates in $L1_0$-ordered TiAl intermetallics containing nitrogen were investigated by transmission electron microscopy (TEM). Under aging at an approximate temperature of 1073 K after quenching from 1423 K, TiAl hardens appreciably due to the nitride precipitation. TEM observations revealed that needle-like precipitates, which lie only in one direction parallel to the [001] axis of the $L1_0$-TiAl matrix, appear in the matrix preferentially at the dislocations. Selected area electron diffraction (SAED) pattern analyses showed that the needle-shaped precipitate is perovskite-type $Ti_3AlN$ (P-phase). The orientation relationship between the P-phase and the $L1_0$-TiAl matrix was found to be $(001)_P//(001)_{TiAl}\;and\;[010]_P//[010]_{TiAl}$. By aging at higher temperatures or for longer periods at 1073 K, plate-like precipitates of $Ti_2AlN$ (H-phase) with a hexagonal structure formed on the {111} planes of the $L1_0$-TiAl matrix. The orientation relationship between the $Ti_2AlN$ and the $L1_0$-TiAl matrix is $(0001)_H//(111)_{TiAl}\;and\;_H//_{TiAl}$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.106-106
• /
• 2009

Al-doped ZnO (AZO) thin films were grown on glass substrates by co-sputtering at room temperature. We made ZnO and Al target and ZnO:Al film is deposited with sputter which has two RF gun source. The Al content was controlled by varying Al RF power and effect of Al contents on the properties of ZnO:Al film was investigated. Crystallinity and orientation of the ZnO:Al films were investigated by X-ray diffraction (XRD), surface morphology of the ZnO:Al films was observed by atomic force microscope. Electrical properties of the ZnO:Al films were measured at room temperature by van der Pauw method and hall measurement. Optrical properties of ZnO:Al films were measured by UV-vis-NIR spectrometer.

• Corrosion Science and Technology
• /
• v.3 no.3
• /
• pp.98-101
• /
• 2004

The corrosion behavior of Al-Fe coatings was studied in the wet-seal atmosphere of molten carbonate fuel cells (MCFC). Fe-8Al, Fe-16Al, Fe-25Al, Fe-36Al, and Fe-70Al (in at.%) specimens were tested in Li/K carbonate at $650^{\circ}C$ by a single cell test and an immersion test. In general, the corrosion resistance of the Al-Fe coatings was enhanced due to the formation of a protective $LiAlO_2$ layer. However, when the Al-Fe coatings didn't have sufficient content of aluminum enough for maintaining the protective layer, the corrosion resistance of the Al-Fe coatings was severely degraded by the growth of non-protective scales like $LiAlO_2$. The test results revealed that the aluminum contents in the coatings should be higher than 25 at.% in order to form and maintain the protective $LiAlO_2$ layers.

• Journal of the Optical Society of Korea
• /
• v.20 no.1
• /
• pp.125-129
• /
• 2016

In this study, we have investigated a high-temperature AlN nucleation layer and AlGaN epilayers on c-plane sapphire substrate by low-pressure metal-organic chemical vapor deposition (LP-MOCVD). High resolution X-ray diffraction (HRXRD), atomic force microscopy (AFM), scanning electron microscope (SEM) and Raman scattering measurements have been exploited to study the crystal quality, surface morphology, and residual strain of the HT-AlN nucleation layer. These analyses reveal that the insertion of an LT-AlN nucleation layer can improve the crystal quality, smooth the surface morphology of the HT-AlN nucleation layer and further reduce the threading dislocation density of AlGaN epifilms. The mechanism of inserting an LT-AlN nucleation layer to enhance the optical properties of HT-AlN nucleation layer and AlGaN epifilm are discussed from the viewpoint of driving force of reaction in this paper.

• Journal of the Korean Vacuum Society
• /
• v.6 no.1
• /
• pp.50-60
• /
• 1997

Undoped, cobalt-doped and erbium-doped $ZnAl_2S_4, ;ZnAl_2Se_4, ;CdAl_2S_4, ;and;CdAl_2Se_4$ single crystals were grown by the chemical transport reaction method. The crystal structures, the lattice constants, the optical energy gaps, and the photoluminescence properties of these single crystals were investigated. Also, the optical transition mechanisms by the impurities of cobalt and erbium were identified from these results.

• Journal of the Korean Ceramic Society
• /
• v.26 no.4
• /
• pp.453-458
• /
• 1989

Aluminum nitride powder prepared from the hydroxides, AlOOH and Al(OH)3 which were obtained by hydrolysis of Al-isopropoxide, was densified at 1750 and 180$0^{\circ}C$ for 60 min by hot-pressing under the pressure of 25kg/$\textrm{cm}^2$. Theoretical density could be obtained at 175$0^{\circ}C$. Their flexural strengths were 450MPa and 395MPa for the specimens obtained from Al(OH)3 and AlOOH, respectively. There was no remarkable change in flexural strength up to 100$0^{\circ}C$. Fracture toughness values were 3.50MN/m3/2 for Al(OH)3 and 3.11MN/m3/2 for AlOOH. It is assumed that these differences in mechanical properties are due to the abnormal grain growth for the AlN ceramics obtained from AlOOH.

• Journal of the Korean Ceramic Society
• /
• v.20 no.1
• /
• pp.49-54
• /
• 1983

The main object of this study is to investigate the effect of Al powder as an additive on the sintering of calcined alumina comparing with that of calcined alumina alone. The degree of Al oxidation is calculated by measuring the weight increase during the firing Water absorption bulk density and compressive strength of the $Al_2O_3+Al$ system at each temperature are compared with those of $Al_2O_4$ alone. The $Al_2O_3+Al$ system shows better physical propeties than Al2O3 alone and it seems by the SEM observation that the fine oxidized Al particles(fine $Al_2O_3$ particles submicron unit) fill the interstices of the original $Al_2O_3$ par-ticles and thus result in the well-close-packed arrangement of the particles.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.3
• /
• pp.157-164
• /
• 1998

Effects of alloying elements on the pitting behavior of Ti-Al intermetalic compounds in the electrolytic soution containing Cl- were investigated through electrochemical tets and corrosion morphologies. Corrosion potential increased in the case of Cr addition to Ti-48%Al, whereas it decreased in the case of Si and B addition. The simultaneous addition of Cr and Si increased passive current density and decrosion corrosion potential. The passive current density of N addtion was higher than that of B addition in H2SO4 solution. With the addition of alloying elements, The pitting resistance decreased in order of TiAl>TiAlSi>TiAlN>TiAlB>TiAlCr and whin siumultaneous addition, it decreased in order of TiAlCrSi>TiAlCrBN>TiAlCrrN. The surface merohology after pitting test showed that the TiAl coataining Si had for fewer pits than that containing Cr and N simultaneously.

• Journal of Korean Society of Water and Wastewater
• /
• v.26 no.2
• /
• pp.229-236
• /
• 2012

The analysis of Al (III) hydrolysis species with PACls prepared by different basicity showed that mononmeric Al species were reduced while precipitate Al species were increased with an increase in basicity for PACls. In the case of the PACl with 13.6% basicity, monomeric Al species were 81%, polymeric Al (III) species 19%, precipitate Al (III) species was 0%, as showing the dominant monomeric Al species. The PACl with 13.6% basicity showed above 80% of turbidity removal efficiency without any restabilization. In addition, the PACl with 13.6% basicity showed higher organic removal expressed by $UV_{254}$ which was caused by lower coagulation pH. The PACl containing the higher amount of monomeric Al species was the most beneficial for T-P and $PO_{4}-P$ removal.

• Journal of the Korean Ceramic Society
• /
• v.27 no.8
• /
• pp.991-1003
• /
• 1990

A precipitation method, one of the most effective liquid phase reaction methods, was adopted in order to prepare high-tech Al2O3/ZrO2 composite ceramics. Al2(SO4)3.18H2O, ZrOCl2.8H2O and YCl3.6H2O were used as starting materials and NH4OH as a precipitation agent, various types of metal hydroxides were obtained by single precipitation(series A) and co-precipitation(series B) method at the pH condition between 7 and 11. Fine Al2O3-ZrO2 powders were prepared at optimum calcination condition and the effects of ZrO2 on microstructures and mechanical properties of Al2O3 were investigated. The composition of Al2O3/ZrO2 composites wax fixed as Al2O3-15 v/o ZrO2(＋3m/o Y2O3). ZrO2 limited the grain growth of Al2O3 and increased grain size homogeneity of Al2O3 more effectively than MgO.Flexural strength values in Al2O3 and Al2O3/ZrO2 composites were 340-430 MPa and 540-820 MPa, respectively, and the effect of strength improvement showed 20-50% by adding ZrO2 to Al2O3. Fracture toughness of Al2O3/ZrO2 composites was improved by stress-induced phase transformation of tetragonal ZrO2 and toughening effect by microcrack was not observed. Also, ZrO2 particles located at Al2O3 grain junction contributed to toughening, while spherical ZrO2 particles located within Al2O3 grain did not contribute to toughening. Weibull moduli of Al2O3 ceramics and Al2O3/ZrO2 composites of series A and series B were 4.34, 5.17 and 9.06, respectively. Above 0.5 of failure probability, strength values in Al2O3 ceramics and Al2O3/ZrO3 composites of series A and series B were above 400 MPa, 700 MPa and 650 MPa, respectively.