• 한국재료학회지
• /
• 제15권2호
• /
• pp.97-105
• /
• 2005

[ $11\AA$ ] tobermorite$(5CaO{\cdot}6SiO_2{\cdot}5H_2O)$ is synthesized from the mixtures of calcium hydroride and quartz using alumina in a molar ratio $Ca(OH)_2/SiO_2$ of 0.8 at $180^{\circ}C$ for 8 and 24 hrs under saturated steam pressure. The influence of alumina on the formation of $11\AA$ tobermorite was investigated by X-ray diffraction, differential thermal analysis and infrared spectroscopy. $11\AA$ tobermorite containing increasingly larger amounts of aluminum showed a shift of the basal spacing from 11.3 to $11.6\AA$. In general, there was a direct linear relation between the basal spacing and added content of alumina. The differential thermal analysis curves showed that $11\AA$ tobermorite with increasing alumina contents exhibited the exothermic peak at high temperature, namely $11\AA$ tobermorite containing aluminum gave a sharp exothermic peak at temperature around $850\~860^{\circ}C$ in the case of $S_3\~S_5$. The absorption band at $1607\~1620cm^{-1}$ is attributed to the bending vibration of water, and the position of the main O-H stretching and Si-O lattice vibration of $11\AA$ tobermorite at 3500 and $965cm^{-1}$ respectively is not altered. Consequently the existence of alumina accelerates the crystallization of $11\AA$ tobermorite, and that the aluminum ion appears to substitute for the silicon ion in $11\AA$ tobermorite structure. Al-containing tobermorite is distinguished from Al-free tobermorite.

• 공업화학
• /
• 제18권5호
• /
• pp.454-458
• /
• 2007

본 연구는 알루미나를 이용하여 수용액 중에 존재하는 $Ca^{2+}$, $Mg^{2+}$, $Sr^{2+}$, $SO{_4}^{2-}$, $NO{_3}^-$, $Cl^-$ 이온의 제거 특성을 분석하기 위하여 실시하였다. 알루미나는 $Al(NO_3)_3{\cdot}9H_2O$와 $NH_4OH$를 사용하여 합성한 수화물을 $450{\sim}750^{\circ}C$로 5 h 동안 열처리하고 FT-IR과 Brunauer-Emmett-Teller (BET)법으로 물성을 분석하였다. 실험결과에 의하면 알루미나의 비표면적은 열처리 온도가 증가하면 감소하는 특성을 나타내었다. 알루미나에 의한 흡착능은 $SO{_4}^{2-}$와 $NO{_3}^-$가 각각 23 mg/g와 12.4 mg/g의 값을 보였다. 반면에 $Cl^-$는 4 mg/g으로 비교적 낮은 값을 보였다. 일반적으로 음이온 제거 효율은 알루미나의 제조를 위한 열처리 온도가 증가할수록 감소하였으며, $450^{\circ}C$로 처리한 알루미나의 경우에 가장 좋은 처리 효율을 나타내었다. 양이온인 $Ca^{2+}$, $Mg^{2+}$, $Sr^{2+}$의 제거 효율은 알루미나의 열처리 온도에 비례하여 증가하는 경향을 보였다.

• 한국결정성장학회지
• /
• 제9권3호
• /
• pp.327-333
• /
• 1999

Ion implantation, photo-lithography, Ar ion milling, hot press를 이용한 micro-fabrication 방법으로 고순도 단결정 알루미나 표면에 Ca를 제한된 양으로 첨가하고, 내부에 여러 가지 형태의 기공을 갖는 bi-crystal을 만들었다. 이 bi-crystal 고순도 알루미나에 미치는 Ca의 영향을 평가하기 위하여 내부 기공의 형태 변화와 결정의 성장을 열처리에 따라 광학현미경으로 관찰하였다. 열처리에 따라 inner crack-like pore의 내부표면에 dot와 육각형의 형태를 갖는 결정 입자가 생성되는 것을 관찰할 수 있었다. $1,500^{\circ}C$로 열처리한 경우에 CaO . $6Al_2O_3$로 생각되는 bar 형태의 결정이 표면에 석출되는 것이 관찰되었으며, 이 결정이 $1,600^{\circ}C$에서 열처리하면 사라지는 것으로 보아 이 온도 부근에서 알루미나에 대한 Ca의 solubility limit 또는 diffusion rate가 변화하는 것으로 생각된다.

• The International Journal of Costume Culture
• /
• 제8권2호
• /
• pp.124-131
• /
• 2005

This study focused on the change of skin temperature by the emissivity and emission power of far-infrared for conformant far infrared effect to naked eyes. The study method is to manufacture the bra pad by each concentration on far-infrared materials of illite powder $(K,H_3O)AI_2(Si,Al)_4O_{10}(H_2O,OH)_2)$, liquid alumina ($Al_2O_3$), the extracted liquid from 29 kind of medical plants, then, measured change of skin temperature. Result are as follows. Far-infrared were emitted each $90.2\%,\;90.1\%,\;89.7\%$ from the illite powder, liquid alumina, extracted liquid from medical plants. When the testee weared the bra pad, the temperature of coated bra pad was $0.5^{\circ}C$ higher than the non finished bra pad. Washing fastness on far-infrared finishing was better dope addition method than coating method.

• 소성∙가공
• /
• 제7권5호
• /
• pp.481-488
• /
• 1998

The active metal brazing was applied to bond Alumina and Ni-Cr steel by Ag-Cu-Zr-Sn alloy and the interfacial microstructure and reaction mechanism were investigated. Polycrystalline monoclinic $ZrO_2$ with a very fine grain of 100-150 nm formed at the alumina grain boundary contacted with Zr segregation layer at the interface. The $ZrO_2$ layer containing the inclusions and cracks were developed at the boundary of inclusion/$ZrO_2$ due to the difference in specific volume. The development of $ZrO_2$ at the interface was successfully explained by the preferential penetration of $ZrO_2$ at the interface was successfully explained by the preferential penetration of Zr atoms a higher concentration of oxygen and a high diffusion rate of Al ions into molten brazing alloy.

• 한국세라믹학회지
• /
• 제34권4호
• /
• pp.380-386
• /
• 1997

The tribological properties of ceramics are very important in the application to engineering ceramic parts such as seal rings, pump parts, thread guides, and so on. In this study, the effects of graphite addition on the mechanical and tribological properties of alumina/graphite composites were investigated. The composites were prepared by the adding of graphite powder to the mixture of Al2O3, talc and calcium carbonate. Bending strength, water absorption, friction coefficient, the amount of worn out material at a certain time, and maximum surface roughness(Rmax) of the prepared composites were measured. Crystalline phases and microstructure were examined with XRD and SEM. The melt of Al2O3-CaO-MgO-SiO2 system was shown over 10 vol% graphite composition. As the amount of the graphite is increased, needle like crystals of mullite were formed and grown. We obtained the good properties of friction coefficients and wear resistance at the powder composition containing 15 vol% of graphite.

• 한국세라믹학회지
• /
• 제25권3호
• /
• pp.284-292
• /
• 1988

Alumina-zirconia composite powders for the purpose of improving fracture toughness and thermal shock resistance of alumina were prepared by the emulsion-kerosene drying method. The average particle size of composite powders was less then 1 $\mu\textrm{m}$ and their shapes were spherical. It was shown that the average particle size of composite powders decreased with the concentration of metal-salt in solution and the amount of span 80 added when preparing emulsions. The structure of all zirconia in composite powders heat-treated at 1200$^{\circ}C$ was a tetragonal form at room temperature. This result implied that fine zirconia particles were homogeneously dispersed in the alumina matrix.

• 한국세라믹학회지
• /
• 제52권3호
• /
• pp.192-196
• /
• 2015

Low soda alumina powder was fabricated using silica (${\alpha}$-quartz) as an agent for removing soda components in the alumina. Quartz powder 2 mm in size was added to aluminum hydroxide obtained through the Bayer process, and then the mixture was heated at various temperatures. Finally, the heat-treated powders were sieved for classification. In this study, the effects of the quartz amount and heating temperature on the mechanism of removing soda were examined. A minimum soda content of 0.005 wt% was observed at the conditions of 15 wt% quartz (based on $Al(OH)_3$ amount) heat-treated at $1600^{\circ}C$ for 8 h. The soda components, such as $Na_2O$, NaOH, and $Na_2CO_3$, in alumina were ionized and activated at high temperature, and this facilitated the reaction with quartz silica and alumina producing nepheline. The advantages of using quartz include low iron content and low cost in comparison with the conventional de-soda process using chamotte, another silicate mineral.

• 한국전기전자재료학회논문지
• /
• 제31권7호
• /
• pp.496-501
• /
• 2018

In this study, we prepared 40, 45, 50, 55, 60, 65, and 70 wt% content composites filled in epoxy matrix for two micro silica and three micro alumina types for use as a GIS heavy electric machine. As a filler type of epoxy composite, micro silica composites showed excellent AC breakdown strength properties compared to micro alumina composites in the case of electrical properties of micro silica and alumina. The electrical breakdown properties of micro silica composites increased with increasing filler content, whereas those of micro alumina decreased with increasing filler content. In the case of mechanical properties, the micro silica composite showed improved tensile strength and flexural strength compared with the micro alumina composite. In addition, mechanical properties such as tensile strength and flexural strength of micro silica and alumina composites decreased with increasing filler content. This is probably because O-H groups are present on the surface of silica in the case of micro silica but are not present on the surface of alumina in the case of micro alumina.

• 한국세라믹학회지
• /
• 제31권5호
• /
• pp.513-519
• /
• 1994

In-situ 반응에 의하여 형성된 La-$\beta$-aluminate (LaAl11O18)로 강화된 알루미나 복합체에 정방정 ZrO2를 첨가하여 알루미나 복합체를 제조하였다. 사용된 분말 혼합체의 조성은 (100-x)[88 Al2O3+(La2O3+11 Al2O3)]+x vol% ZrO2였으며, x는 0부터 40까지 변화시켰다. 열간가압형성에 의하여 얻어진 치밀한 소결체는 1200MPa의 곡강도값을 나타내었다. 이러한 높은 곡강도값은 첨가한 ZrO2 입자와 기존의 La-$\beta$-aluminate platelets의 기지 입자에 대한 입성장 억제 효과와 ZrO2의 응력유기 상변태 효과로부터 기인하였다. 상기 복합체의 파괴 인성도 역시 8.58.5 MPa.m1/2까지 증가하였는데, 이러한 파괴인성의 증가는 ZrO2의 상변태 강화와 미세균열 강화, 그리고 La-$\beta$-aluminate와 ZrO2 입자의 균열 deflection과 bridging의 효과로 설명되어질 수 있다.